Change license owner to Prevas due to initially wrong owner due to company
mix-up during co-development.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
This demonstrates the ADC driver added in the previous commit. The
sample reads A0 as well as two built-in channels - one that reports
the internal 1.2 reference volatage and one that reports half the
analog supply voltage.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Remove parts of overlays for nRF targets that were just copied from
the adc_dt sample but are not used by the adc_sequence sample and only
generate confusion here.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a board-specif dts overlay file for the adc_dt sample on the
STM32F4-DISCO board to enable for ADC channel support.
Signed-off-by: Ajith Anandhan <ajithanandhan0406@gmail.com>
Add board-specific overlay file for the adc_dt sample
on the STM32F0-DISCO board to enable ADC channel support.
Signed-off-by: Sudarsan N <sudarsansamy2002@gmail.com>
AIN9 source needs special handling (all from AIN8-AIN14). Conversion
result needs to be scaled up by 3.6 additionally to gain and reference
voltage. In order to achieve correct value in the sample vref-mv is
used as reference voltage instead of predefined internal reference
source.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Sample is reading vref-mv property to get reference voltage and then if
reference source is set to ADC_REF_INTERNAL this value is overwritten.
If vref-mv property is provided then it should not be overwritten.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Changed reference to ADC_REF_EXTERNAL0 as it is the only value supported
by current driver implementation and 3v3 external reference is connected
on the board.
Signed-off-by: Dhanesh S R <sr.dhanesh@protonmail.com>
- Remove duplicated conf/.overlay configuration for
mimmxrt1170_evk A and B revisions that have the same content.
- No change if .conf/.overlay have different content.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Use the `arduino,uno-adc` mapping to change the settings
to make it easier to understand.
Add available A4 and A5 pins.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Remove the support of the Nucleo WBA52CG board since it is NRND
(Not Recommended for New Design) and it is not supported anymore
in the STM32CubeWBA from version 1.1.0 (July 2023).
Signed-off-by: Nidhal BEN OTHMEN <nidhal.benothmen@st.com>
Pinoroni Pico Plus2 is an RP2350B based board that has
more rich I/O, RAM, and Flash than the original Raspberry Pi Pico2.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
nucleo_C071rb overlay file contains all ADC node configurations
to be able to run the sample.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Move overlays and conf from boards to socs in following samples :
- samples/drivers/adc/adc_dt
- samples/drivers/counter/alarm
- samples/drivers/dac
- samples/subsys/settings
Signed-off-by: Marek Matej <marek.matej@espressif.com>
add more samples
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Add support for xg24_rb4187c to the ADC sample app. Configure two
channels, one measuring the AVDD supply against the 1.21V bandgap
reference, and one measuring pin PB1 (wired to button 0) against
the AVDD (VDDX) reference.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Remove ADC2 support (identified as adc1 entry)
for additional ESP32-C3 based board targets.
Other boards have those instances already deleted.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add overlays for nrf54h20dk_nrf54h20_cpuppr. Moved common configuration
for nrf54h20dk to nrf54h20dk_nrf54h20_common.dtsi. Add configuration
for vpr_launcher on nrf54h20dk_nrf54h20_cpuapp.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This examples shows how to use the AD4114 ADC on a
stm32f3_disco board.
As the AD4114 is a 24bits ADC resolution we need to be able
to pass 32bits buffer to get the samples.
CONFIG_SEQUENCE_RESOLUTION is set to 12 instead of 24, and the
gain zephyr,vref-mv is adapted to avoid overflows using the
exisiting adc_raw_to_millivolts function.
Signed-off-by: Pierrick Curt <pierrickcurt@gmail.com>
The Raspberry Pi Pico 2's device is compatible with the existing Pico 1.
The build system requires a `<board>.overlay` file, but these use the
pre-processing to #include the sibling rpi_pico.overlay files rather
than duplicating the contents as an attempt to keep things DRY.
Tested locally.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
Convert qspi and hyperflash to variants instead of revisions by popular
demand.
And convert evkb into a revision instead of a different board.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
A valid device tree configuration is provided for the ADCs of the 8 input
channels and the sample adc_dt works out of the box. Obviously this is
not the only possible configuration but it provides a good template for
further customization without the need to lookup the ADC GPIOs and
connections in the schematics.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
