For the CCM mode, increase slightly the output buffer size because
the cc23x0 directly fills this buffer with 16-byte blocks.
This prevents from doing unnecessary memcpy that would have an
impact on the driver's performance.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Extend several flash samples and tests so that they can also be used
with "jedec,mspi-nor" devices.
Add configurations needed for the nrf54h20dk/nrf54h20/cpuapp target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
native_posix is being removed as it has reached its end of life in 4.2,
after being deprecated since 4.0.
So these overlays will not serve any purpose anymore.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
native_posix is being removed as it has reached its end of life in 4.2,
after being deprecated since 4.0.
Remove the twister support for native_posix[//64] and therefore all
references to them from the testcases and samples yamls, so twister
does not error out.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This updates the documentation of all the EnjoyDigital boards to use
the new `zephyr:board::` directive.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
The harness was set to ztest, but the sample requires the console
harness to match on the "sample complete" line, its not actually
using ztest.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Allow user to add shell commands in testcase/sample yaml file
alongside the harness_config like in the console harness.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
This commit adds support for these multicore samples:
- samples/drivers/mbox
- samples/drivers/mbox_data
- samples/subsys/ipc/ipc_service/static_vrings
- samples/subsys/ipc/openamp
Signed-off-by: Tomas Galbicka <tomas.galbicka@nxp.com>
Add configuration and board overlay in the I2S audio codec sample to
demonstrate usage of the newly introduced audio output feature.
Signed-off-by: Titouan Christophe <moiandme@gmail.com>
The shell harness expects the UART can be routed to stdin/out on POSIX
arch based targets, but this is not the case for the bsim targets (at
least not yet, and not using the native_posix UART configuration option)
This causes these tests to fail timing out in CI => let's filter these
platforms by now.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add i2c_bus_short fixture to the rtio_loopback sample to ensure it
is only run on boards with the bus shorted. The i2c_bus_short
fixture is also used in the i2c_target_api test suite.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Enable spi_flash sample for MAX32655FTHR and MAX32655EVKIT
which have an external Winbond W25Q128jv external flash.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Signed-off-by: Rob Cornall <Rob.Cornall@analog.com>
Signed-off-by: Yasin Ustuner <Yasin.Ustuner@analog.com>
Enable DAC entry in device tree and pinctrl (PB13/PB14).
Update doc/yaml files to include ADC info.
Update the sample for sam4s_xplained.
Signed-off-by: Ibe Van de Veire <ibe.vandeveire@basalte.be>
nucleo_C071rb overlay file contains all ADC node configurations
to be able to run the sample.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Move overlays and conf from boards to socs in following samples :
- samples/drivers/adc/adc_dt
- samples/drivers/counter/alarm
- samples/drivers/dac
- samples/subsys/settings
Signed-off-by: Marek Matej <marek.matej@espressif.com>
add more samples
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Add support for xg24_rb4187c to the ADC sample app. Configure two
channels, one measuring the AVDD supply against the 1.21V bandgap
reference, and one measuring pin PB1 (wired to button 0) against
the AVDD (VDDX) reference.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
The sample app draws rectangles in the corner of the display.
On devices with the SCREEN_INFO_X_ALIGNMENT_WIDTH capability,
each draw needs to transmit a complete line. Make the sample
work on such displays (e.g. the `ls0xx` driver) by making the
rectangles take up the full width of the display.
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Remove ADC2 support (identified as adc1 entry)
for additional ESP32-C3 based board targets.
Other boards have those instances already deleted.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
The user of the ft8xx driver can register a callback function called
on a touch detection interrupt event. This function is extended to
include a user-defined pointer. The user-defined pointer helps to share
a callback with multiple driver instances.
Signed-off-by: Hubert Miś <hubert.mis@gmail.com>
Improve the FT8xx display driver to support multiple driver instances.
The ft8xx_reference_api.h still follows the FT8xx programming guides,
limiting the usage of the driver to one instance.
Signed-off-by: Hubert Miś <hubert.mis@gmail.com>
Add overlays for nrf54h20dk_nrf54h20_cpuppr. Moved common configuration
for nrf54h20dk to nrf54h20dk_nrf54h20_common.dtsi. Add configuration
for vpr_launcher on nrf54h20dk_nrf54h20_cpuapp.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Rename video_fourcc() to VIDEO_FOURCC(), differing from the Linux
implementation, but more compliant with the coding style.
Also introduce a VIDEO_FOURCC_FROM_STR() to generate a FOURCC format
code out of a 4-characters string.
Signed-off-by: Josuah Demangeon <me@josuah.net>
This commit adds support for these multicore samples:
- samples/drivers/mbox
- samples/drivers/mbox_data
- samples/subsys/ipc/ipc_service/static_vrings
- samples/subsys/ipc/openamp
Signed-off-by: Tomas Galbicka <tomas.galbicka@nxp.com>
This examples shows how to use the AD4114 ADC on a
stm32f3_disco board.
As the AD4114 is a 24bits ADC resolution we need to be able
to pass 32bits buffer to get the samples.
CONFIG_SEQUENCE_RESOLUTION is set to 12 instead of 24, and the
gain zephyr,vref-mv is adapted to avoid overflows using the
exisiting adc_raw_to_millivolts function.
Signed-off-by: Pierrick Curt <pierrickcurt@gmail.com>
