Ram, ram_text and ram_ro regions will be accessed by all CPUs, so that
setting them to INNER_SHAREABLE is more reasonable.
'rbar' occupies 6 bits, correct it to 6.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
The logs were not visible when an assert fired on the controller and
`CONFIG_BT_HCI_VS_FATAL_ERROR` was not set.
Putting the logs in panic mode before entering the infinite loop fixes
that.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Add a cast to struct bt_audio_codec_qos for the macro so
that the returned value can used for e.g. sizeof or
similar.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
remove mcux test scenario, which is overlapped with default
limit test to boards listed in the boards list
fixing: #62067
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
The Calibration value of the VRef on stm32U5 is acquired on 14Bit by ADC1
and should be adjusted on 12bit becasue the resolution is 12bit
in this stm32_vref driver.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Interrupt is enabled before reset is released to make sure that the
first IRQ edge is captured, and rx thread can process it.
Remove delay in spi_open as it was redundant due to the "sem_initialised"
semaphore.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
Update build documentation for openamp sample, to reflect that sysbuild
is required when building this sample. Sysbuild is needed to build both
core images in one step.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This utility header was accessing directly the interrupt
controller HW models, but those are not an interface one
can expect to not change, or to be avaliable in different
targets.
Instead we change it to use the APIs we have a contract
about, that is, the ones all POSIX arch boards are
expected to provide.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
The posix_soc_if.h header includes all functions
one can expect any native board will provide.
These two functions (to set and clear an interrupt
from SW) were missing, but they are also required.
Add them.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Rename BT_AUDIO_CODEC_QOS_[UN]FRAMED to
BT_AUDIO_CODEC_QOS_FRAMING_[UN]FRAMED and give a name
to the enum, which is then used by the
struct bt_audio_codec_qos.
The rename was needed as we had a codec_qos initializer of the
same name, so the values were renamed to avoid duplicated
macro names.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Replace incorrect and limited runtime parity/data bits conditional
configuration with build-time logic using BUILD_ASSERT. This allows for
more flexible UART configurations, while preventing invalid DTS
configurations at build-time.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Move overlapping UART parameter configuration to new
uart_stm32_parameters_set function. This function is called by
uart_stm32_configure upon application/subsystem configuration, and
uart_stm32_registers_configure upon (re-)initialization of driver
instances.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Move clock enable and register configuration to their own functions in
preparation for later uart_stm32_reinit function that will use these in
addition to uart_stm32_init.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Add static uart_config struct to init macro with corresponding pointer
as uart_stm32_config struct member. This struct will store boot and
runtime UART configuration for reinitialization upon exiting low-power
modes, where register contents might be lost.
Remove hw_flow_control, parity, and baud_rate from uart_stm32_config and
uart_stm32_data structs, respectively, as the need for these is now
obviated by the presence of the uart_config struct, which contains
equivalent members.
Add default baudrate, parity, stop, and data bits constants, used to
initialize the uart_config struct, in case the corresponding UART DT
properties are not set.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Move reset configuration from uart_stm32_data to
const uart_stm32_config struct, as this is set once at boot and isn't
modified during runtime.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Move select include directives from source to header file, as these pull
data types required by the struct definitions contained within it.
This promotes a more modular file structure.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
The assert on L3_MEM_BASE_ADDR is incorrect, we need must convert
to uncached before use.
Fixes: ffd2121c65 ("soc: xtensa: intel_adsp: cavs: fix
power_down_cavs() signature")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Add missing definitions for ALH DAIs. Keep the same FIXME
reminder in the comments we have for ACE1.5 that explains
the background of these definitions.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Before, only following way of getting test-item build was supported:
`west build -b <BOARD> -T <PATH_TO_SOURCE/TEST_NAME>`
This commit allows to also call it by:
`west build -b <BOARD> <PATH_TO_SOURCE> -T <TEST_NAME>`
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
i.MX RT SoC have some pins related to the watchdog.
For example, iomuxc_gpio_ad_b0_15_wdog1_rst_b_deb allows WDOG1_RST_B_DEB
signal to be used as reset source for i.MX RT10xx boards.
Signed-off-by: Benjamin Lemouzy <blemouzy@centralp.fr>
The var "uart_xlnx_ps_driver_api" is defined twice in the source,
so remove one definition of it.
Signed-off-by: Florian La Roche <Florian.LaRoche@gmail.com>
k_cycle_get_32() expands to RTC->COUNTER in nrf_rtc_counter_get(),
sys_clock_hw_cycles_per_sec() expands also properly.
Signed-off-by: Witold Lukasik <witold.lukasik@nordicsemi.no>
Update SNVS pin names in RT11xx DTSI files to align with new pin data
generated for the RT1176 and RT1166 processors. This pin data is stored
within the NXP HAL, so the SHA of the HAL is also updated by this
commit.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove commands which are already defined as subcommands for command
ivshmem. Moreover those commands recursively include themselves as
subcommands.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
To properly setup L1 exit timing this patch will use buffer interrupt
for HOST DMA and wait for Host HDA to actually start
First interrupt will clear all others.
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
This header is private and included only in architecture code, no need for
it to be in the top of the public include directory.
Note: This might move to a more private location later. For now just
cleaning up the obvious issues.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If network interface name support is enabled, print the name
when showing network interface data.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Make sure we use the network interface name (if configured)
instead of device name when binding to certain network
interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
If CONFIG_NET_INTERFACE_NAME is enabled (default is y), then
system will automatically set a user friendly name to the network
interface like eth0, wlan0 etc.
Application can change the interface name if needed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
