The SERCOM4 is hardwired to PB30/31, PC18/19 internally for the LoRa
radio. Move the pinctrl entries to SoC dts level. The same applies for
samr35.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In general, peripherals should be disabled by default and enabled at
board level when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add the ability for the flash simulator to store its contents in a
memory region.
This allows filesystems on the flash simulator to survive a reboot.
And allows subsystems (e.g. coredump) to store their info on ram while
using the (existing) flash partition backend.
Add a example (for nucleo_f411re) that shows how to configure the flash
simulator for hardware (cfg discussion #54166).
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a generic NTC, `ntc-thermistor-generic`. In this case,
the compensation table is provided via devicetree. Note that DT property
is prefixed with `zephyr,`, because while hardware related, it is linked
to a particular software implementation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactor driver to align a bit more with its Linux counterpart, ie,
ntc_thermistor. This driver did quite a few _unconventional_ things,
like using "zephyr," compatibles, a dedicated node for pre-computed
compensation table (referenced by the actual pseudo-device node), etc.
The comparison helper function should likely be simplified as well (to
avoid the need for custom wrapper for bsearch), but this can be done
later.
In this refactor, each thermistor gets a compatible, e.g. "epcos,xxxx".
Compatibles are known by the driver, so are compensation tables. This
simplifies devicetree files. There's no need to bother about
compensation tables in **every** board file if Zephyr supports a certain
NTC model.
In general we should respect Linux bindings, which in the end influence
how drivers are implemented. In this case, this principle resulted in
simplified, easier to use code.
For future developers, this is how support for a new NTC can be added:
1. Add to the end of the driver:
```c
#undef DT_DRV_COMPAT
#define DT_DRV_COMPAT vnd_model
static __unused const struct ntc_compensation comp_vnd_model[] = {
{ x, y },
...,
};
#define DT_INST_FOREACH_STATUS_OKAY_VARGS(NTC_THERMISTOR_DEV_INIT,
DT_DRV_COMPAT, comp_vnd_model)
```
3. In driver's Kconfig make sure it depends on
DT_HAS_$DT_DRV_COMPAT$_ENABLED
Note: $X$ means _value_ of X.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
It looks like the Zephyr thermistor driver bindings were half-copied
from Linux ntc-thermistor. Zephyr principle is to maintain compatibility
with Linux, when possible, so there's no reason to deviate here. Convert
the connection type from a custom enum to a boolean, as Linux does.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add Silicon Labs xG24-PK6010A (BRD4187C radio plug-in board)
support to the efr32_radio board.
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
This commit moves the `mpfs-icicle.dtsi` file to a common `microchip`
directory and updates include paths in the `mpfs_icicle` board
devicetree.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Initial sensor driver for NPM1300 PMIC charger.
Includes basic configuration of charger voltage and current.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
All Nucleo boards provide the ST Morpho connector/header, which exposes
all pins of the MCU. It is tipically used in ST shields, so provide a
nexus node to allow creating generic shields.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add Port 14/15 to device tree. These ports can only be configured as input.
Error out in gpio driver if user sets them as output.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
XMC4500 and XMC47/800 MCUs have a different memory layout. The
definitions have been moved to the derivative .dtsi of each MCU.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
This patch introduces support for NXP S32 CANEXCEL (CANXL) peripheral.
CAN protocol supporting:
- CAN classic
- CAN FD
Remote transmission request is not supported as this feature is not
available on NXP S32 CANXL HAL.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Added RTC driver that supports Motorola MC146818B
Enabled RTC set/get time and alarm, alarm callback
and update callback.
Counter and RTC uses same hardware in case of
Motorola MC146818, so they can't be used at a time.
Updated stand-alone mc146818 counter dts instances
to support rtc and counter with same compatible
string of "motorola,mc146818" on ia32, atom,
apollo_lake, elhart_lake and raptor_lake platforms.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
This patch adds support for the TI INA3221 current monitor.
This is the datasheet used for reference:
https://www.ti.com/lit/gpn/ina3221
Since this device has three channels, there is a custom attribute to
select which channel is to be used when getting a sample.
Measurements are done on all enabled channels.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Make it possible to use CPOL/CPHA SPI clock modes with the SDHC driver.
Some cards require the clock to switch to low when not active.
Signed-off-by: Łukasz Hejnak (LeHack) <lehack-ghub@lehack.pl>
The current configuration is too long and will block soc from
entering sleep mode. This change was made to get better power
number on EVB.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add a binding for STM32 ADC to specify the resolutions and all associated
register information (through a STM32_ADC_RES macro).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This is a new parameter to divide the LPTIM input clock
by a prescaler, changing the max reachable timeout of the LP timer.
It will divide the LPTIM input clock by 1 (reset value) up to 128.
The lptim configuration register is written with a 3bit value.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
CAVS platforms are not fully integrated with zephyr. Some of the
registers are still programed from SOF side. This feature can be enabled
for those platforms later when integration is fully done.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Implements a UART driver using PIO. Both PIOs are supported.
Only polling API is supported. Only 8N1 mode is supported.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
- To link image loadable by MCUboot, zephyr,code-partition
must be set in the DTS.
- Move partition definitions from SoC DTS to the board DTS.
- Remove scratch partition since MCUboot does not recommend to use it.
- Increase bootloader partitions to 48K to fit recent MCUboot.
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
The newly added "power-amplifier-output" property for STM32WL SubGHz
radio nodes is mandatory.
Add the property to all affected modules and boards with the
appropriate value for the factory-default hardware configuration.
Add the "rfo-XX-max-power" properties to all affected modules and
boards with the appropriate value for the hardware configuration.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Add STM32WL-specific sx126x_set_tx_params function based on the
STM32CubeWL modifications to LoRaMac-node.
Add the "power-amplifier-output" DT property to
"st,stm32wl-subghz-radio" for selecting between the RFO_LP and RFO_HP
output configurations provided by the above mentioned function.
Add the "rfo-lp-max-power" and "rfo-hp-max-power" DT properties for
defining the maximum design power of the respective outputs' matching
networks.
closes#48511
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Adds a retention system which builds on top of retained_mem
drivers to allow partitioning of areas and data integrity with
magic header prefixes and checksum of stored data.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Adds address cells of size 1 and size cells of size 1 to GPREGRET
instances for Nordic devices.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This commit adds support for the `drivers.adc` test by adding an overlay
for the `efr32bg22_brd4184a` board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
EFR32MG24 uses the Secure Element's mailbox for entropy gathering
purposes. Reflect that in the device tree structure.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
