The RGB565 and BGR565 formats are interchanged in the sample. This leads
to wrong assumptions about "byte swap" in Zephyr and make display
drivers, shields and video sample follow it for a long time. Fix it.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Formats should be coherently set between camera and display. Forcing
RGB565 to BGR565 will break some platforms.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
1. Update nxp irtc driver to fix issue in init and alarm function.
2. Update RTC device tree binding to support "share-counter".
3. Update RT700 dtsi to support rtc0 for cpu0 and rtc1 for cpu1.
4. Update readme.
5. Update unit test project conf for RT700.
Signed-off-by: Holt Sun <holt.sun@nxp.com>
This replaces the legacy SDFW compatible board configuration with the
IronSide SE compatible one, thus removing support for running samples
and tests on nRF54H20 devices with the old firmware.
All applications are expected to work on `nrf54h20dk/nrf54h20/cpuapp`
out of the box. For other board targets, all applications are expected
to boot, but may require additional peripheral configuration in UICR.
Build system support for the new UICR format is to be added separately.
Co-authored-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Switch which board is the remote in the test case for
mbox communication between nrf54h20dk/nrf54h20/cpuapp and
nrf54h20dk/nrf54h20/cpurad, making cpurad the remote instead.
This is done to prepare the sample for executing with IronSide SE,
where using cpurad as the main board doesn't make as much sense,
since cpuapp has to start cpurad.
Signed-off-by: Jonathan Nilsen <jonathan.nilsen@nordicsemi.no>
Board overlays were moved from downstream to upstream.
By mistake, License was left unchanged.
Change License type to match with the upstream.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
When a board contains two identical flash memories configured in
parallel dual-flash mode, the actual sector size is twice the sector
size of a single flash memory. So, assuming 4-KiB sectors for each flash
memory, any erase operation must be 8-KiB aligned.
This commit updates the start offset and sector size in the spi_flash
sample to be properly aligned when a dual-flash configuration is used.
At the moment, this is only supported for STM32-based boards and QSPI
flash memories.
Signed-off-by: Thomas Altenbach <altenbach.thomas@gmail.com>
Expand this sample to also work with GNSS_RTK through a serial client.
Make this compatible to work with VMU_RT1170 which requires using the
F9P, instead of the M8 UBX module.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Remove duplicated test configuration after
nrf54l20pdk/nrf54l20/cpuxxx was renamed to
nrf54lm20dk/nrf54lm20a/cpuxxx.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Add overlays required to run the sample on
- nrf54h20dk/nrf54h20/cpuapp,
- nrf54l15dk/nrf54l15/cpuapp,
- nrf54lm20dk/nrf54lm20a/cpuapp.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Remove duplicated test configuration after
nrf54l20pdk/nrf54l20/cpuxxx was renamed to
nrf54lm20dk/nrf54lm20a/cpuxxx.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Remove duplicated test configuration after
nrf54l20pdk/nrf54l20/cpuxxx was renamed to
nrf54lm20dk/nrf54lm20a/cpuxxx.
Extend platform_allow with other nrf54* targets (overlays for these
targets already exist in the boards directory).
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Remove duplicated test configuration after
nrf54l20pdk/nrf54l20/cpuxxx was renamed to
nrf54lm20dk/nrf54lm20a/cpuxxx.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
Add overlays used for testing differential mode support in STM32 ADC
driver:
- Nucleo F303K8
- Nucleo H753ZI
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
This commit adds test overlays for the siwx917_dk2605a board.
It also adds an overlay for the i2s sample.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
For all LED drivers, the underlying subsystem is automatically selected
in Kconfig if their compatible node is found in DT.
The only exception is the PWM LED driver which depends on PWM instead
of selecting it. The PWM Kconfig option must be explicitely selected in
order to have LED_PWM enabled.
This patch updates the Kconfig of the PWM LED driver to have the same
behavior as other LED drivers: PWM is now automatically selected if a
"pwm-leds" compatible node is found in DT.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Restructured counter and timer.
CTimer/Timer is now parent to pwm and counter.
Created PWM driver and tied to pwm and pwm-led
Signed-off-by: Richard Wheatley <richard.wheatley@ambiq.com>
Add support for using the SMARTDMA engine on the FRDM-MCXN236 board with
the video capture sample.
Replace console pins, because default console pins(P1_8, P1_9) are
duplicated with camera header pins.
Signed-off-by: Neil Chen <cheng.chen_1@nxp.com>
adp_xc7k/ae350/clic uses a different interrupt controller than
adp_xc7k/ae350, add overlay files as in adp_xc7k/ae350.
Signed-off-by: Jimmy Zheng <jimmyzhe@andestech.com>
Update common flash test and jesd216 samples to work on the
APARD32690-SL board which has MX25U6432FM2I02 on-board.
Signed-off-by: Pete Johanson <pete.johanson@analog.com>
rename gpio stepper to h bridge stepper
minor correction in stepper_stop, stepper_stop shall cancel all active
movements and should not be concerned about keeping the coils energized
or not, since that is a concern of a motion controller and not a stepper
driver.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
When adding new fsbl variant this sample Kconfig overlay was missed
leading to non functional sample on this variant.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
moves adafruit_feather_esp32s3_tft_reverse_procpu.conf file
to the correct folder after PR was merged.
Signed-off-by: Philipp Steiner <philipp.steiner1987@gmail.com>
Avoids shadowing the outer 'ret' variable by reusing it instead of
redeclaring it inside a conditional block.
This improves code clarity.
Signed-off-by: Gaetan Perrot <gaetan.perrot@spacecubics.com>
Immediate log mode may use a lot of stack and hence may cause some stack
overflow on some boards.
Enable deferred log mode to have the least impact on the application.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Add condition to do the test pattern fixture test only if the test
pattern control was successfully set.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
Demonstrate the crop/compose API by introducing 4 new
CONFIG options in order to define the crop area.
Moreover, if the selection API is available and if
the targetted size is different from the current crop
size, then try to apply a compose in order to reach
the targetted format size.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Replace i2s_write invocation with i2s_buf_write invocation for test sine
wave playback.
When CONFIG_USE_DMIC=n, this sample attempts to play back a test sine
wave encoded in sine.h. As the i2s_write treats the given buffer as a
memory slab, it overwrites parts of it, resulting in data corruption and
improper playback. i2s_buf_write accepts a buffer existing outside the
playback queue (heap).
Manually tested on mimxrt595_evk/mimxrt595s/cm33 where it was first
observed.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Utilize a code spell-checking tool to scan for and correct spelling errors
in `Kconfig` files within the `arch`, `boards`, `kernel`, `modules`,
`samples`, and `share` directory.
Additionally, incorporates a fix recommended by the reviewer.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Ensure the I2S echo sample only configures the audio_codec driver
when the `audio_codec` node is defined and enabled in the devicetree.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Remove the build instruction from README about using the native_sim
without using the video-sw-generator snippet, as it cannot build.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Add macros giving hints to users using #error, about what might be
missing to build and run the samples, such as a missing "chosen"
devicetree node.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Extends support and adds new overlays.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
