This commit configures the testcase to run on the
stm32u5x5 target boards. USART2 is selected
Pins Tx and Rx (PD5 PD6 on CN9) must be connected on the HW board
to pass the test.
The USART transfer uses the GP DMA transfer with request
27 and 26 on 2 DMA channels (0-15).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit configures the testcase to run on the
stm32u585 target boards. USART3 is selected
Pins Tx and Rx (PD8 PD9 on CN14) must be connected on the HW board
to pass the test.
The USART transfer uses the GP DMA transfer with request
28 and 29 on 2 DMA channels (0-15).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Configure through an overlay file, the nucleo_wb55rg board
for running the tests/drivers/uart/uart_async_api.
DMAMUX is used for transfer on channels 0 & 1 with
LPUART peripheral request 17 & 16.
No hw flowcontrol for this test.
Connect pin A0 & A1 of CN8 to PASS the test.
Note that I2C3 pin assignment might conflict (PC0 & PC1).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Initialize devices at compile time. Also fix some ready check problems
(e.g. in async test readiness failure just resulted in a printk, but
test continued...).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a bunch of missing "zephyr/" prefixes to #include statements in
various test and test framework files.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Following zephyr's style guideline, all if statements, including single
line statements shall have braces.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move to use DEVICE_DT_GET instead of device_get_binding as we
work on phasing out use of DTS 'label' property.
Also, fixed issue that change exposes with SEGGER RTT testing
in that in some platforms the device getting selected for the
RTT test was not the RTT device.
Signed-off-by: Kumar Gala <galak@kernel.org>
This PR adds support for the RT1060_EVKB as a variant of the RT1060 EVK.
Blinky app tested locally on RT1060_EVKB.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
This sets the dts of dma for using the uart 6 asynch api.
The stm32f746 has a dma V1 with request 5 for Tx/Rx usart6
The Tx&Rx pins (PG14, PG9) of the usart6 are connected
on the nucleo_f746zg board to pass the test
The CONFIG_DCACHE=n must also be set to disable Dcache.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This sets the dts of dma for using the uart 6 asynch api.
The stm32f767 has a dma V1 with request 5 for Tx/Rx usart6
The Tx&Rx pins (PG14, PG9) of the usart6 are connected
on the nucleo_f767zi board to pass the test
The CONFIG_DCACHE=n must also be set to disable Dcache.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In order to bring consistency in-tree, migrate all tests to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
add nxp,loopback mode to boards with LPUART. This will enable testing
the UART async api without a physical loopback connection.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
define uart peripheral that can be connected as a loopback using
external jumper for all boards this test can be run against.
Additionally, all RT boards require DMA memory to be noncacheable. Move
SRAM to DTCM for all RT10xx series boards, and to noncacheable OCRAM for
RT11xx series.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Intention of the test is to abort rx few bytes after start of
transmission (before it is completed). Previously, thread was busy
waiting after start of TX and aborted RX from that context. However,
it may happen that CPU is busy handling UART transfer and
k_busy_wait prolongs beyond full transfer which results in test
failure.
Move rx_abort to k_timer timeout which is run in interrupt
context.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a test case that ensures that uart_rx_enable() can be successfully
called after RX is disabled with uart_rx_disable() and also when it is
disabled automatically after the provided RX buffer is filled up.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
However, there are cases when milliseconds granularity is not
enough and can significantly reduce a throughput, e.g. 1ms is
100 bytes at 1Mb.
Updated 4 drivers which implement asynchronous API. Updated
places where API was used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
It enables the usart6 to run the testcase with a DMA
tests/drivers/uart/uart_async_api. DMA2 (of type V1)
is configured on channel 5 (request) streams 7 & 2.
USART Tx and Rx PG14 - PG9 pins (14 & 16 of CN10)
are connected to PASS the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This sets the dts of DMA for using pn the uart 2 i.
The stm32h723 has a DMAMUX and request are 44 and 43 for usart2
The Tx&Rx pins PD5 and PD6 of the usart2 are connected
on the nucleo_h723zg board to pass the test
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add configuration for testing the usart3 through the dma1
on the nucleo_l152re target.This test requires the Tx pin
to be connected to the RX pin on the board.
Pin definition is added for this usart instance.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit configures usart3 to use dma in uart_async_api test
on nucleo_l552ze_q platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit configures usart3 to use dma in uart_async_api test
on stm32l562e_dk platform. Short pin2(PC10) & pin 3 (PC11) of usart3
in CN4 connector on stm32l562e_dk platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Adds nucleo_g071rb board to the uart_async_api test.
Therefore additionally add usart1 in board definitions.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This sets the dts of dma for using the uart asynch api.
The stm32l475 has a dmamux with request 2 for Tx/Rx usart4
The Tx&Rx pins (PA0, PA1) of the usart4 are connected
on the disco_l475_iot1 board to pass the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds the asynchronous UART API testing support on the
nucleo_l4r5zi board.
The usart3 module is used as the secondary loop-back UART, which is
required to run this test.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
After finish transmitting some bytes might be in the
peripheral receive register, since the transmition
is still happening after reception disabled.
This patch ensures that the peripheral has no
bytes in its internal state.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Extend the test_single_read test case to catch RX_RDY events that are
not expected to appear.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The cached device pointer must be placed in memory that allows user
mode invocation of the test functions to access it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The device pointer is now provided to the callback, there is no need to
call uart_callback_set() with the device being set a user data.
Fixes#26923
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert DT_UART_{0,1}_NAME to DT_NODELABEL() references as the cases are
board specific and this allows us to remove DT_UART_{0,1}_NAME defines
in dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the asynchronous UART API testing support on the SAM
D21 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
We rename the nRF91 Dev Kit board target (nrf9160_pca10090)
to nrf9160dk_nrf9160. We update all associated references
in the supportive documentation and all nRF9160-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
