The nRF54L05 and nRF54L10 are identical to the nRF54L15 except for their
memory sizes. Add support for emulating those ICs on the nRF54L15DK.
This commit only adds support for the main application core. Support for
the FLPR core may be added later.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
It will increase test coverage for adc driver, no test uses
ADC_GAIN_2_3 setting yet.
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
Tests are checking error codes returned from adc_read() and
adc_channel_setup() used with invalid configurations.
Signed-off-by: Bartlomiej Buczek <bartlomiej.buczek@nordicsemi.no>
Use EXTRA_CONF_FILE in sample yaml files,
that replaced deprecated OVERLAY_CONFIG
since the Zephyr v3.4 release.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Change the unit of the sense resistor in the devicetree binding from
micro-ohms to milli-ohms. This is done for three reasons.
Firstly, the maximum value resistor that can currently be represented
is 4.2 kOhms, due to the limitation of devicetree properties to 32 bits.
Secondly, storing the resistance at such a high resolution makes
overflows much more likely when the desired output unit is micro-amps,
not milli-amps.
Finally, micro-ohms, are an unnecessarily precise unit for the purpose
of these calculations, and a resolution that is not realistic to
achieve. The high resistor resolution results in large divisors that
reduce the resolution of outputs. Unlike resistors characterised down to
the micro-ohm, devices wanting to measure micro-amps are actually
realistic.
Signed-off-by: Jordan Yates <jordan@embeint.com>
-add nucleo_u083rc and stm32u083c_dk overlays files
for testbench purpose.
- add platform_exclude property to skip test on boards
with little ram size.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
tests: drivers: adc: adc_api: update adc_api test
native_posix is now deprecated.
Building these tests in both native_sim and native_posix does not
improve coverage for the tests or subsystem but doubles CI time.
As anyhow native_posix will be removed all together in
2 releases, let's remove it already for these.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add support for flashing the Adafruit Feather nrf52840 Express
using UF2 over USB.
Also standardise on using the UF2 variant, so add a non UF2 variant
of the Sense board, so it can be flashed using the SWD headers.
Created flash dtsi files for both SWD and UF2. These are actually identical
for many other boards and should probably be moved to common in future.
Signed-off-by: Jacob Winther <jacob@9.nz>
Update both versions of adafruit feather nrf52840 to be variants rather
than separate boards. The aim is to provide a more consistent approach
and to remove some unnecessary Kconfig redundancy.
Signed-off-by: Jacob Winther <jacob@9.nz>
Commit consists of minimal set of overlays need to run tests
and samples. Additionally disables nRF54L15 platform in cpp98
tests, because unnamed unions are not supported.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Move samples config files from 'boards' to 'socs' in order to
remove multiple files with the same configuration and render
available samples for new boards. Only changed sample files
which are not board or hardware specific.
Signed-off-by: Raffael Rostagno <raffael.rostagno@espressif.com>
Adafruit feather is a generic name that could match many
boards. Renamed to reflect actual board name:
- Adafruit Feather nrf52840 Express
There are two boards based on the nrf52840, so keeping directory
generic to support additional board defs with mostly shared dts.
Signed-off-by: Jacob Winther <jacob@9.nz>
This commit changes the adc_api test to use the proper printf
format specifier when printing the ADC samplings. This ensures
that all values are printed on 16-bit. Without this specifier,
negative values are sign-extended and printed on full integer
size (e.g., 0x8000 -> "0xFFFF8000").
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
This nucleo board inherit from the root `h5` dts some special nodes:
- `vbat` on adc1 channel 2
- `vref` on adc1 channel 17
- `die_temp` on adc1 channel 16
The issue is discussed here:
https://github.com/zephyrproject-rtos/zephyr/issues/72914
Signed-off-by: Alex Fabre <alex.fabre@rtone.fr>
`checkpatch.pl` requires that dts sources are indented with tabs,
fix all the spaces that slipped in while checkpatch wasn't watching.
Signed-off-by: Jordan Yates <jordan@embeint.com>
add the stm32h7s78_dk disco kit to run the tests drivers
This testcase is executed (XiP) from the external NOR
of the stm32h7s78_dk board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
A collection of simple enablements to match some of the enablement
done for rd_rw612_bga as closely as possible on the frdm_rw612 board.
- i2c
- spi
- dma
- mrt
- ctimer
- os timer
- dac
- adc
- trng (alread was enabled but now listed support)
- watchdog
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Rename all Silicon Labs dev kits to always use the official kit name
as board target name. Previous kit names used various naming schemes,
including putting part of the SoC name in the board name. With HWMv2,
SoC names (if needed) should go in the SoC board qualifier.
Use HWMv2 revisions for the two variants of SLTB010A.
Split the xG27 Dev Kit from the EFR32BG22 Thunderboard. This attempt
at deduplication is confusing due to the very different kit names
and use of different ICs (BG22 vs BG27), and was not continued with
the xG24 Dev Kit, meaning that it wasn't consistent.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
