Introduce GPIO-based driver for MIPI DBI class that allows MIPI DBI
type A and B displays to be used on general platforms.
Since each data pin GPIO can be selected individually, the bus pins are
set in a loop, which has a significant negative impact on performance.
When using 8-bit mode and all the data GPIO pins are on the same port,
a look-up table is generated to set the whole port at once as a
performance optimization. This creates a ROM overhead of about 1 kiB.
Tested 8-bit 8080 mode with ILI9486 display on nRF52840-DK board.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
Instead of always using the SPI MIPI DBI mode (type C), look up the
mipi-mode from the device tree and only set the mode to
MIPI_DBI_MODE_SPI_4WIRE as a fallback in case the property is not given.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
This commit removes the y-selection of the `CONFIG_PINCTRL` Kconfig option
in FE310-based boards defconfig files.
It also makes drivers used in FE310 y-select `CONFIG_PINCTRL` if pinmuxing
is needed.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
On some EDMA versions, some TCD registers (e.g: SADDR, DADDR,
SLAST, DLAST, etc...) are extended to 64 bits via adding a new
HIGH register holding the value of bits [63:32]. Since, for now,
the driver doesn't support 64-bit addresses, this scenario is
supported by sign-extending the 32-bit value written to SLAST/DLAST.
SADDR and DADDR are taken care of on HAL side.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Some EDMA versions may have the channel MUX register in the MP
region. To support this scenario, use the `EDMA_HAS_MP_MUX_FLAG`
flag to figure out which channel MUX register to use (TCD or MP).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Currently a user, or a shield definition, must select a Kconfig to
signal that the iovdd_ctrl and bucken GPIOs are connected to the same
pin. We can instead check this in the driver by simply checking if
the iovdd_ctrl_spec and bucken_spec are the same pin.
Update the nrfwifi driver and remove the redundant
NRF_WIFI_COMBINED_BUCKEN_IOVDD_GPIO config.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Register all the lpi2c instances.
Add no-power-level property and update driver
to adapt no-power-level property.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
The mcr20a driver referencing `MCR20Overwrites.h` which is under
`hal/nxp/mcux`.
So, put `depends HAS_MCUX` for clarify the dependency.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
When building with native_sim, We need to specify
```
#define _POSIX_C_SOURCE 200809L
```
to make `gmtime_r` available.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Fixes the mailbox notification callback that was not
being called from the ISR when the other side sends
something.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Sometime, the radio causes a bus error.
This happens because we cast a struct and access to a member
that doesn't exists in the original struct.
This updates the driver to use the right struct to make the cast safe.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Currently, if we try to write data from a memory mapped flash address
to the flash then we get a -EINVAL error.
This could break the settings subsystem when we use NVS backend.
In order to make it work, add a buffer and use it when we want to
write data that is located in flash address space.
This has been tested using sample/subsys/settings/
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Do not allocate TxFIFO in a way that could corrupt Endpoint Information
Controller data (stored at DFIFO Depth address) or access locations
outside the SPRAM.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add timer device name autocompletion to the commands.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
These callback functions are not used outside of the file, make
them `static`
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
This reverts commit 311ddf90e2. That
commit breaks firmware boot on both MTL and LNL.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
For code clarity, this commit adjusts the use of `return` statements
in functions with a void return type as follows:
- Transform `return foo();` into separate statements:
`foo();`
`return;`
- Remove unnecessary `return` statements when
they don't affect control flow.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
By keeping track of run-time ATT MTU of all connected peers, it's
possible to increase the notification payload size; thus increasing
data-throughput sent over Bluetooth.
Note that this assumes the Bluetooth connection is properly configured
(with the corresponding connection parameters) to optimize performance.
This is application-specific and shall be examined on each scenario for
optimal performance.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Add the function, i3c_device_is_controller_capable, to determine if
a target is controller capable.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The Active Controller data struct for static addr is to always be
0x7E. This is so the active controller can be identified according
to section 5.1.9.3.7 of the I3C v1.1.1 Specification.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
The local function ll_gpio_get_pin_pull() is not always referenced. Add
the __maybe_unused attribute to avoid compiler warnings (which may be
promoted to errors by downstream users).
Signed-off-by: Keith Short <keithshort@google.com>
Since b249535 (sensors: Add channel specifier) the signature of
sensor_reconfigure_read_iodev() changed, but sensor_handlers.c
apparently hasn't been updated.
Fix compile time error by updating sensor_reconfigure_read_iodev()
signature in sensor_handlers.c
Signed-off-by: Andrea Merello <andrea.merello@iit.it>
All kscan drivers have been moved over to input, Mark the kscan driver
class as deprecated so it can be removed in the 4.2 release.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Now that we support internally connected channels we should make the
pinctrl configuration optional.
Signed-off-by: Corey Wharton <xodus7@cwharton.com>
Adds support for configuring the STM32 DAC channel mode for internal
connections. This is only enabled for SOCs that support it.
Signed-off-by: Corey Wharton <xodus7@cwharton.com>
Due to the introduction of `shell_fprintf_normal` in PR #77192, we can
minimize caller overhead by eliminating direct `color` parameter passing.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Aligned the `struct shell *` argument name from `shell_ctx` to `sh`
for consistency with other drivers' usage of `sh`, and to match
the `shell_cmd_handler` argument name.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
The `<id>` argument was included in `cmd_i3c_ccc_getvendor`,
`cmd_i3c_ccc_setvendor`, and `cmd_i3c_ccc_setvendor_bc` but
was not processed.
Utilized `shell_strtoul` for proper parsing of the `<id>` argument
in these functions.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Resolved a compilation error where `maxwr`, `maxrd`, and
`max_read_turnaround` were incorrectly referenced.
The code was updated to correctly access these fields from
the `data_speed` structure.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Correct used lines based on write opcode
regardless of the data mode.
The write opcode is set during init for all
modes and can be overwritten in DT.
Add lines correction for PP_1_1_2.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Deprecate support for configuring the MCO source and prescaler from
Kconfig configurations.
This is now done by devicetree and an MCO driver instead, which also
configures the pin to be used by the MCO peripheral.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add device driver for STM32 MCO peripheral which takes configures
the MCO clock source and prescaler, and outputs it on one of the GPIO
pins.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Add clock sources PLL2CLK, PLL3CLK and EXT_HSE.
Needed to check that these clocks are enabled in MCO code.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
Extracted common SPI RTIO operations from the spi_mcux_lpspi driver
into spi_rtio, which should be common across RTIO drivers.
Tested with spi_loopback with and without CONFIG_SPI_RTIO. Ran on
mimxrt1010_evk.
Also, verified the other SPI RTIO driver (spi_sam) is not broken by
these changes (tested building for target: robokit1 with the same
conditions as above).
Signed-off-by: Luis Ubieda <luisf@croxel.com>
