There are no more context defines specific to metadata, the ones
coming from Assigned Numbers shall be used.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Some build configurations in direction finding samples
sample.yaml didn't have harness=bluetooth. That enables
these configurationsto be be executed on hardware by
CI. Those runs end causing CI failures.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The littlefs_mount() function sets the mount point for block devices,
so fname[12] shall be generated after calling it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Up till now, the littlefs sample program was only supporting the flash
medium. However, it would be also welcome to be able to test reading and
writing data from littlefs stored on block devices - like SD card.
In this case we do use the block API, to read and write data to it.
To achieve this goal - the CONFIG_APP_LITTLEFS_STORAGE_BLK_SDMMC define
has been introduced.
One can change the disk mount point by defining board specific
CONFIG_SDMMC_VOLUME_NAME.
The test for nucleo board equipped with SD card shall be built with:
west build -p always -b nucleo_h743zi ./zephyr/samples/subsys/fs/littlefs \
-DCONF_FILE=prj_blk.conf
Moreover, the README.rst has been extended to describe running this
test on block devices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The littlefs_flash_erase() function shall be called from flash specific
littlefs_mount function. This allows removal of the stub function
when block device support is added.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This KConfig define (by default defined) is necessary to extend the
littlefs test functionality to support other test scenarios - for
example running it on device with block device (i.e. SD card) backend.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit extends the littlefs test to use binary pattern file.
This file has the 0x55 and 0xAA patterns (to avoid fast wear leveling)
written alternately with special "marks" bytes on each eight position.
Those values are incremented each time the board boots. One can adjust
the size of this file with the TEST_FILE_SIZE define.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The code responsible for incrementing the in-file value has been moved
to the separate function for better readability and reusage.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The code for presenting content of the directory, has been moved to the
separate function to be easily reusable.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Replace calls to printk with LOG_PRINTK to use the logging Zephyr
infrastructure. After this change it would be possible to set the
logging mode (to e.g. reduce the verbosity of output and final size
of the binary).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The gsm modem should be able to be started or stopped freely,
independent from the networking state.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
The `starting` flag causes the sample to work only if
GSM_PPP_AUTOSTART is enabled, its initial value should be
dependent on GSM_PPP_AUTOSTART.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Rename
BT_CTLR_LLCP_PROC_CTX_BUF_NUM
to
BT_CTLR_LLCP_LOCAL_PROC_CTX_BUF_NUM
to match naming scheme of
BT_CTLR_LLCP_REMOTE_PROC_CTX_BUF_NUM
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
Use NRF_DT_GPIOS_TO_PSEL() in calls to nRF GPIO HAL functions as they
need a psel value, a pin number combined with the corresponding GPIO
port number, not only the pin number as provided by DT_GPIO_PIN().
This way buttons connected to pins in the P1 port can also be handled
properly.
Replace also DT_NODELABEL(button0) with DT_ALIAS(sw0) for consistency
with other samples that use the standard button.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To give control over GPIO pins for Direction Finding Extension of
Radio peripheral when build for nRF53 network core, the application
core has to assign those pins to network core.
There is a mechanism that uses a device tree overlay to get
information about GPIO pins to be assigned to network core.
The commit adds overlays with appropriate configuration
to assign GPIO pins in all DF related samples.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
As the receive window is now decreased at the TCP module level, other
direct net_context users are also responsible for acknowledging the
received data with net_context_update_recv_wnd() - otherwise, the
communication will stall.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The capabilities callback did not provide information about
the type of the endpoint being configured, making it
impossible for the application to determine if it is a
sink or source endpoint.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Audio streams as defined by the BAP spec does not
support bidirectional audio streams. This commit
updates the API and implementation to match that.
The use a bidirectional CIS with 2 audio stream will
be added in a future commit.
This removes the _IN_ and _OUT_ and _INOUT_ QOS
values, as well as the direction of the codec QOS
struct.
To keep direction for internal use, the direction
has been added to the endpoint struct.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Make it consistent for audio.h and capabilities.h that the
array size parameter appear after the array parameter.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This enables CONFIG_LOG_BACKEND_UART_OUTPUT_DICTIONARY so that
the UART backend is in dictionary logging mode.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Reserve the upper 8 bits of gpio_dt_flags_t for SoC specific flags and
move the non-standard, hardware-specific GPIO devicetree flags (IO
voltage level, drive strength, debounce filter) from the generic
dt-bindings/gpio/gpio.h header to SoC specific dt-bindings headers.
Some of the SoC specific dt-bindings flags take up more bits than
necessary in order to retain backwards compatibility with the deprecated
GPIO flags. The width of these fields can be reduced/optimized once the
deprecated flags are removed.
Remove hardcoded use of GPIO_INT_DEBOUNCE in GPIO client drivers. This
flag can now be set in the devicetree for boards/SoCs with debounce
filter support. The SoC specific debounce flags have had the _INT part
of their name removed since these flag must be passed to
gpio_pin_configure(), not gpio_pin_interrupt_configure().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The overlay are defined to run the samples application with PWM
feature on the nucleo_l073rz,nucleo_f091rc, nucleo_g474re
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The metairq sample sometimes failed due to stuck because it has a
potential race when recording the latencies. The previous solution
checks whether the stats.mirq greater than MAX_EVENT. But stats.mirq
might also have a race here. So we change to check the msg sequence,
its correctness ensured by the kernel's message queue.
And also remove the spinlock in previous fix because tests only use
1 CPU, no need to add this. It also improves the fix for #40889,
to prevent test failed sporadically on acrn_ehl_crb and ehl_crb.
Fix#42874.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add build assertions that will ensure that every peripheral for
which a driver instance is created has some pins assigned to it.
Neither pinctrl-0 nor *-pin properties can be currently marked as
required in devicetree, so these assertions will help users avoid
invalid configurations where it could be hard to figure out why
the UART is not working.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Pinnacle 100 DVK uses QSPI to store slot1 partition.
Add board config overlay to ensure QSPI is enabled
so slot1 can be read/written.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
This sample application uses the STM32 USB TCPC Driver to create a USBC
Sink Application for the STM32G081b_eval board.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
the icm42605 defaults to a global thread for trigger processing,
the CONFIG_ICM42605_TRIGGER_OWN_THREAD is deprecated.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Add the support of a rpmsg tty channel that responds to the generic
Linux rpmsg_tty driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Restructure to separate the management of the rpmsg stack
add the rpmsg client into 2 threads.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
The Bluetooth HCI driver based on the RPMsg transport now uses the IPC
service module. The compatible Bluetooth sample - HCI RPMsg - has also
been migrated to the new IPC solution.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Kconfig options now belong to the Kconfig domain, therefore, the
:kconfig:option: role needs to be used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This file defines the crypto driver API, cipher is supposed to be just
one type of capability (other can be hash) of these drivers, just
change the file name to be consistent with it.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
