Adds properties to configure OCTOSPI IO
Manager data lines. That allows to use
any `IOLowPort` and `IOHightPort`.
Note: OSPIM requires additional clock to be enabled.
Please refer to Reference Manual.
Extra clock can be enabled in devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Add Nuvoton numaker series UART support, including interrupt-driven,
also apply pinctrl and clock-control.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add Nuvoton numaker series clock controller support, including:
1. Do system clock initialization in z_arm_platform_init().
2. Support peripheral clock control API equivalent to BSP
CLK_EnableModuleClock()/CLK_SetModuleClock().
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add support for communication with serial ports on native POSIX platform
via UART driver API. Serial port driver supports polling API,
configuration of the serial ports used via devicetree and command line
options, and runtime configuration with `uart_configure`.
Multiple instances of the driver are supported.
Example use and configuration is also demonstrated in the
`samples/drivers/uart/native_tty` sample.
Closes: #56586
Signed-off-by: Marko Sagadin <marko.sagadin42@gmail.com>
Add simple mechanism to load the image from IMR memory. Basically we are
only setting a flag in power off for the next boot to jump to existing
image in IMR.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
The IS31FL3216A is a fun light LED controller. The LED current of each
channel can be set in 256 steps by adjusting the PWM duty cycle through
an I2C interface.
Signed-off-by: Guy Morand <guy.morand@bytesatwork.ch>
Add a minimal driver for the ti lp5569 led controller. The driver supports
multiple instances. Commands on|off|set_brightness are supported.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
Currently, only the presence of a GIC is reflected in the device tree,
and its version must be set separately in each SoC's Kconfig.
This patch adds separate bindings for each GIC version whose presence
in the device tree automatically enables the corresponding Kconfig symbol.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
When the GIC driver was originally introduced, it was only used on
Cortex-R SoCs. However, this is not the case anymore. Update the
description to reflect that this driver is not specific to Cortex-R.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
Add driver for TCN75A temperature sensor. The following features are
supported:
- TCN75A oneshot mode, which allows single shot conversions with lower
power consumtion
- Resolution selection, up to 12 bit resolution (9 bit default)
- Triggering based on temperatue thresholds. If the TCN75A exits a set
threshold range, the application can be notified via a callback.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Add a new pinctrl driver for TI CC32XX SoC. The driver has not been
tested, just implemented following datasheet specs and checked that it
compiles. Consider this as a best-effort driver to remove custom pinmux
code in board files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This PR adds a custom driver for the ADS1112 ADCs. Unlike ADS1113/4/5
family served by the ADS1x1x driver, the ADS1112 does not use an address
pointer to address config registers. Instead, there is only one writable
register and all i2c writes will set it. The registers resemble the
ADS1119 device, but config bitmap is different, include a distinct data
rate table, gain table, and input multiplexing table. There is also not a
status register to be monitored with the ADS1112, as it uses config bit 7
for the same purpose instead of a separate register.
The driver was tested on hardware using the ADC shell interface. Manual
probing validated the voltages for the MUX_SINGLE configs at datarate 15
in CM_SINGLE. Higher gains were not tested and CM_CONTINUOUS is not
supported in this initial implementation.
The new driver has also been added to the existing ADC test using adc_emul
for completeness.
Origin: original
License: Apache 2.0
Purpose: Adding support for ADS1112 ADCs
Signed-off-by: Jordan Montgomery <jordan.montgomery@getcruise.com>
Move dt files related to SoC family and series to npcx folder. It only
leaves SoC dt file in `dts/arm/nuvoton folder` in case of confusion with
the other Nuvoton SoCs.
The dt files path will be:
dts/arm/nuvoton
|--npcx
| |--npcx7
| | |--npcx7-miwus-wui-map.dtsi
| | |--npcx7-alts-map.dtsi
| | |--.....
| +--npcx9
| | |--npcx9-miwus-wui-map.dtsi
| | |--npcx9-alts-map.dtsi
| | +--.....
| |--npcx-miwus-wui-map.dtsi
| |--npcx-alts-map.dtsi
| |--npcx.dtsi
| |--npcx7.dtsi
| |--npcx9.dtsi
|--npcx7m6fb.dtsi
|--npcx7m6fc.dtsi
|--npcx9m8f.dtsi
+--npcx9m3f.dtsi
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the two UART nodes so that they are under "soc" rather than "espi",
leave only xec-espi-host-dev nodes there.
The UART device can be used indepdently by the driver uart_mchp_xec.c
and it's normally initialized before before the espi one.
Moving the device node up a level so this does not trigger a false
positive on the build time priority checking.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The BG95 pin configuration does not internally ever use the reset pin.
Because of this, there is no need to make reset pin mandatory.
Commit removes reset pin dependency [e.g. in case of BG95].
Signed-off-by: Andrei Hutanu <andrei.hutanu.i@gmail.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
