The CMSDK uart interrupts for TX and RX can either be treated as a
signel interrupt line or distinct interrupts for TX & RX. In the case
that they were distinct we didn't get the ifdef correct based on DTS.
If we have 2 interrupts in DTS we assume they are for TX & RX and thus
build the interrupt support for distinct TX & RX ISRs.
Also, cleanup handling of UART_2..UART_4 to be similar to how
UART_0/UART_1 code is using DT_INST_IRQN(x).
Fixes#30770Fixes#25601
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A recent patch removed use of the cfg structure, but left a pointer to
it defined which causes build failures.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The NPCX clock driver was already using devicetree, just need to make a
small tweak to use DEVICE_DT_INST_DEFINE and update NPCX_CLK_CTRL_NAME
to match the label for the "nuvoton,npcx-pcc" clock controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a simple pinctrl node for the IOF registers under the GPIO
controller node to be used by the pinmux driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert esp driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop CONFIG_WIFI_ESP_NAME
option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Convert ublox-sara-r4 driver:
NET_DEVICE_OFFLOAD_INIT -> NET_DEVICE_DT_INST_OFFLOAD_DEFINE
DT label is already required, so use it and drop
CONFIG_MODEM_UBLOX_SARA_R4_NAME option.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This include make possible to use the arm_arch_timer on
platform such as Cortex-A9 or Cortex-R7 which has support for
ARM Global Timer.
The global timer is a 64 bit incrementing counter, memory-mapped
in the private memory region.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
In some cases we cannot know the BDF up-front, so provide a way to
look it up based on the vendor and device ID.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These have been redefined in various places - better to have them in a
single place that different users can use.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add ESPI SAF features to the Microchip eSPI driver as
a separate file. ESPI SAF depends upon the core eSPI
driver adding the ability to attach the system SPI
flash to the EC eSPI endpoint instead of the host
eSPI controller.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
During the driver init, the function will set the sensor resolution
based on the driver's dts variable "resolution"
The driver's device tree has been updated to include the value
"resolution".
The default is set to the highest resolution of 0.0625C.
Moved mcp9808_reg_write from mcp9808_trigger.c to mcp9808.c
This allows resue of the same function in both the trigger and
resolution functions.
Function name changed to xxx_16bit to distinquish it from the 8
bit write function that will added.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
In this CL, npcx_miwu_interrupt_configure is no longer responsible for
turning the interrupt off. Although the default state of WK_EN is
disabled, the users still have the chance to configure them when WK_EN
is enabled via npcx_miwu_irq_enable(). Hence, this CL also ensures that
WK_EN is disabled before configuring them.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL uses a simpler configuration approach that turns GPIO's
interrupts off instead of calling npcx_miwu_interrupt_configure
with NPCX_MIWU_MODE_DISABLED.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit introduces runtime query of the HW Capabilities of
the nRF IEEE 802.15.4 Radio Driver.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
Add posibility to configure UART_X device
based on board dts config.
Enable uart clock only if node is enabled
Signed-off-by: Pavlo Hamov <pasha.gamov@gmail.com>
nRF5340 PDK board was deprecated in v2.5.0 release
and is removed now from the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
By the time hostname configuration was implemented, driver was switching
only between STA and STA+AP modes. After dynamic selection between NONE,
STA, AP and STA+AP was implemented (commit referenced below), hostname
configuration no longer takes effect when ESP chip obtains address over
DHCP (and sends hostname in the DHCP request).
Set hostname each time after enabling STA mode, so that it takes effect
in DHCP requests.
Fixes: 03ce61004b ("drivers: wifi: esp: control CWMODE depending on
current needs")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add some simple depends so we limit various I2C drivers to the SoC
families that the drivers are relevant to.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On I2C V1 parts, LL_I2C_EnableIT_TX() translates to EVT and BUF
IRQ enabling.
In stm32_i2c_msg_write function, LL_I2C_EnableIT_TX is called right
after stm32_i2c_enable_transfer_interrupts which already enables BUF
IRQ, which starts the transfer.
As a consequence it could happen that transfer is already complete
at the time LL_I2C_EnableIT_TX is called. This case is not expected
by remaining part of the code which loops forever waiting for BUF IRQ
to be raised.
Remove the superfluous LL_I2C_EnableIT_TX call.
Fixes: #32265
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
nRF52840, nRF52810, nRF52811 and nRF52805 are affected by anomaly 242.
This patch introduces workaround for this anomaly as follow:
Power-fail comparator is disabled before any attempt to erase or write.
Either erase or write is not proceed if EVENT_POFWARN is
already asserted.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Introduce support for situation when synchronization back-end
aborts operation before it is done. synchronization API will
transfer operation return code to the driver shim back.
Additionally:
FLASH_OP_ONGOING value was switched to be positive in order to
not been mislead with a negative error code.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Keep OOB Rx channel and interrupt always enabled.
Send callback when packet is received in OOB Rx channel
if asynchronous host-initiated handling is enabled.
Note that driver doesn't perform any buffering from packets,
so access to OOB Rx channel is gated by client's driver
packet retrieval.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Currently assumption is all OOB traffic over eSPI bus is always client
initiated.
Add option for systems where host can initiate OOB traffic.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The calculated alarm time starts from 2000 but the gmtime_r needs as
input the time from epoch (1970). This causes the alarm time to be
miscalculated due to leap years, as 2000 is a leap year and 1970 is not.
To fix the issue, the 2000 timestamp can be added to the input time of
gmtime_r.
Fixes#32260
Signed-off-by: Antonis Sioutas <antonis.si510@gmail.com>
Fixes: "WARNING:CONSTANT_COMPARISON: Comparisons should place the
constant on the right side of the test"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32 uart driver doesn't support 9bits transactions in any case,
so remove case were it was declared as supported.
Fixes#31799
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit fixes sporadic kernel panics when writing big data chunks
to the flash. (data bus errors)
Reference manual:
If an erase operation in Flash memory also concerns data in the data
or instruction cache, you have to make sure that these data are
rewritten before they are accessed during code execution.
If this cannot be done safely, it is recommended to flush the caches
by setting the DCRST and ICRST bits in the Flash access control
register (FLASH_ACR).
Signed-off-by: Alexander Wachter <alexander.wachter@leica-geosystems.com>
If statement was unconditionally reading a field from async struct
while pointer to this struct may be null if asynchronous API is
enabled but given driver instance is not using it.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Driver uses DEVICE_AND_API_INIT which is deprecated so convert
to using DEVICE_DT_INST_DEFINE instead.
Fixes#32151
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are several different issues when trying to build the icm42605
sensor driver:
* Missing entry in drivers/sensor/CMakeLists.txt
* Issues with #ifndef in header files
* Issues with const usage
* Missing function prototypes in headers
* Fix use of LOG_MODULE_REGISTER v LOG_MODULE_DECLARE
* Add missing dts node to tests/drivers/build_all/spi.dtsi
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update NPCX PWM driver so PWM can be turned off as the first call when
PWM_POLARITY_INVERTED is used.
Signed-off-by: Keith Short <keithshort@google.com>
Disable the DIO1 interrupt when the sx126x modem is in sleep mode.
On nRF hardware, this lets the `GPIOTE` hardware be switched off, saving
15uA.
Fixes#31569.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Update the global state of the modem on calls to `SX126xReset` and
`SX126xWakeup`. This stops `SX126xCheckDeviceReady` sending spurious SPI
commands on every transieve before `SX126xSetOperatingMode` is called.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Drivers are using DEVICE_AND_API_INIT which is deprecated so convert
the iproc_pax dma drivers over to using DEVICE_DT_INST_DEFINE and
DEVICE_DT_INST_GET.
Fixes#32153
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The callback pointers for uninitiated operations are implicitly null;
making them explicit only confuses maintainers searching for drivers
that implement the API.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Iterate through all lmp90xxx device instances found in the devicetree
and initialise all of them.
Fixes#32046.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix coverity CID 216784.
SJW was not initialized in the tmp_res, but got copied
to the result pointer, which overwrites the value.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
This CL prevents the transaction result overwritten by the recovery
function. Even if the recovery mechanism succeeds, the upper layer still
needs to know why the transaction failed.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Since all fields' type in SMBST is R/W1C and RO, setting a single bit to
clear a specified event is a more suitable solution. Or we might clear
the other pending bits that occurred at the same moment unexpectedly.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL reset i2c event-completed semaphore before starting
transactions. Some interrupt events such as BUS_ERROR might change its
counter when i2c bus is idle. It causes that the driver cannot wait
for the event completed and return immediately.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
So far received packets were parsed (at AT command level) and allocated
in [esp_rx] thread. Then they were submitted to [esp_workq] thread for
processing (calling application callback).
This flow results in following deadlock when esp_workq thread waits on
response to some AT command:
- [esp_rx] waits on allocation of new RX packet
- [esp_workq] waits for [esp_rx] to process response to AT command
that was just sent
- blocked [esp_workq] prevents processing and deallocating RX packets
- [esp_rx] times out on allocation and closes socket
Process RX packets directly from [esp_rx] thread to prevent above
deadlock.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This is a fix for ACRN targets. Qemu ivshmem original specs do not
states that, if ivshmem-plain is selected, bar0 (the register bar) will
not be present. It just says that bar2 will only be sufficient.
And that is what happens on qemu: whether ivshmem-plain or
ivshmem-doorbell is selected, bar0 is always present no matter what.
This does not seem to be the case in ACRN which does not expose the
bar0 if ivshmem-plain is selected.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Gracefully shutdown the UARTE peripheral when the async API is used.
Failure to do so results in the driver being unusable when powered back
up as the required events (ENDTX & TXSTOPPED) are not set. This also
ensures that the last byte sent out via `poll_out` is properly output
on the serial line before powering down.
Fixes#31930.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Update the drivers power state knowledge immediately after calling
`nrf_uarte_enable`. This ensures that the state is correct regardless of
which path the function exits by.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fixes the bug when driver changes offset after
the callback call. When you have the ready event
you suppose no changes in driver data after that.
Fixes#31973
Signed-off-by: Alexander Shuklin <jasuramme@gmail.com>
The count register is 64 bits, but we're a 32 bit CPU that can only
read four bytes at a time, so a bit of care is needed to prevent
racing against a wraparound of the low word. Wrap the low read
between two reads of the high word and make sure it didn't change.
Fixes#31599
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When checking for IRQ flags, we should also check
for IRQ status (IsEnabled ?).
If this is not done we can end up in Half Transfer
interrupt processing while it is not enabled.
Additionaly always use the id translation function
in LL API calls.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch fixes warnings for unused variables when acceleremoter
range and sampling frequency are set to values different from
the defaults.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Power consumption was still high after putting uarte device into off
state. It was caused by ENDRX interrupt that was triggered after
calling STOPRX. ENDRX event was called with 0 amount but interrupt
got triggered and fifo_read was starting RX again.
Added disabling RX interrupt before disabling UARTE and reenabling at
device activation.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Some format strings were causing warnings.
As elsewhere in this file, offset is type-casted (or not,
depending on compiler) to long int, and then %ld is used in
format string.
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
Start using DTS values for PCI Vendor ID and PCI BDF. For the PCI
Device ID we do not use DTS since this would require changing overlay
for different SKU board.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The function uart_irq_rx_ready() should return true if there is data in
the receive buffer, regardless of whether the irq is enabled. Fix the
mcux and rv32m1 shim drivers to implement this behavior correctly.
Prior to this change:
- irq_rx_full() checks if RX data is available
- irq_rx_ready() checks if RX data is available and interrupts are
enabled
After this change:
- irq_rx_full() checks if RX data is available
- irq_rx_ready() renamed to irq_rx_pending() to avoid confusion with the
API ready() function
- API ready() implementation switched to use irq_rx_full()
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
socket_can_generic.h makes some assumptions that are not always valid
for various drivers with regards to numbering. To clean this up we
add defines for SOCKET_CAN_NAME_0 and SOCKET_CAN_NAME_2 in addition to
SOCKET_CAN_NAME_1.
We also move struct socket_can_context into the drivers themselves
since they know best how many CAN interfaces are getting supported and
what naming/number convention they'd have.
Additionally, this also exposes a few other build issues with the
can_mcux_flexcan driver that get fixed.
Finally, we remove the platform_allow from samples/net/sockets/can
since it is no longer needed.
Fixes#31733
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ESP fetches DNS servers from local network by using DHCP. There is an AT
command to get those DNS addresses. Use that to provide DNS addresses
for Zephyr's DNS resolver.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Rather than Kconfig vendor symbols, select stm32 watchdog using
compatible.
So user only has to enable the requested node and set
CONFIG_WATCHDOG=y.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix the timeout computation to provide more accurate timeouts
versus requested timeout.
Additionally, the error margin is reworked in order to:
- be relative to the application requested timeout (10% tolerance)
- exclude timeouts inferior to application request
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This CL added more additional details for KBC (Keyboard and Mouse
Controller) bus in espi_event structure. It helps the application to
handle different 8042 events in the callback function.
The format of event data for KBC 8042 protocol is:
[23:16] - 8042 event type: 1: Input buf full, 2: Output buf empty.
[15:8] - 8042 data: 8-bit 8042 data.
[0:7] - 8042 protocol type: 0: data type, 1: command type.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Socket can be closed either by Zephyr or by peer. In the former case ESP
WiFi chip still notfies about closed socket, which currently results in
printing warning log:
<wrn> wifi_esp: Link X already closed
Change level of this log from warning to debug, so that driver users are
not concerned about situation that is a normal behaviour.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Force sx12xx modems into sleep mode on boot. This is the default state
of the modem when not being used due to the TX/RX complete callbacks.
This reduces current consumption by 600uA before the modems are used
for the first time.
As sleep is the normal state after TX/RX when using the LoRa API, it is
garaunteed that this will not change the behaviour of application code.
LoRaWAN starts by calling Radio.Init(), which resets the modem, so any
sleep configuration we do here is discarded.
Fixes#31567.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
`SENSOR_CHAN_GAUGE_AVG_CURRENT` is currently treated as a capacity
by the MAX17055 driver, however the unit conversion is different
for current and must be calculated separately.
Add a separate method to convert a current reading to milliamps
from 1.5625 uV/R_SENSE units, instead of the 5uVH/R_SENSE conversion
that was previously used.
Tested by comparing value read and converted from MAX17055 with
value from an external power profiling kit.
Signed-off-by: Hayden Ball <hayden@playerdata.co.uk>
For multiple channels detection, channels variable was compared with
the output of find_lsb_set which actually is a decimal number.
Since channel is a bitfield the comparison was not behaving as
expected (detecting several channels while only one channel was used).
Rework the code to use the already existing bitfield "index" for
the test.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There was a regression when implementing automatic AT+CWMODE{,_CUR}
handling based on driver needs. ESP AT 1.7 firmware does not support
AT+CWMODE_CUR=0, which means that radio needs to be either in STA, AP or
STA+AP mode (no NONE state available).
Fix ESP AT 1.7 compatibility by keeping radio in STA mode whenever it is
not used.
Move also first AT+CWMODE_CUR invocation before AT+CWDHCP_CUR, so that
the latter executes successfully with ESP AT 1.7.
Fixes: 03ce61004b ("drivers: wifi: esp: control CWMODE depending on
current needs")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The ',' character was used as line terminator instead of ';'
in SPI routines. The three affected drivers were not showing
any issue, but the typo is fixed for clarity.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This allows out-of-tree libraries to implement their own temperature
driver.
We allow selecting TEMP_NRF5 to aviod dependency loops
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
With this change it is possible to share all configurations
related to CLOCK_CONTROL_NRF_K32SRC_RC_CALIBRATION without
including the clock calibration configurations.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Clock calibration should only be used when RC source is used.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The GPIO driver uses a proprietary GPIOTE channel allocator.
This commit makes it use the allocation mechanism provided by nrfx.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
idle is only considered in other timer implementations if ticks ==
K_TICKS_FOREVER but in arm_arch_timer. Just fix it.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Added ap_enable and ap_disable api. The driver will open create an
access point with DHCP Server ip 192.168.1.1 and no security.
Added a small fix for the AF_INET issue.
Added parent and remote to accept routine context.
Added put implementation.
Signed-off-by: Nicolai Glud <nicolai.glud@prevas.dk>
net_context contains both net_sock_type and net_ip_protocol, which are
static during the lifetime of net_context. net_context has basically the
ownership of esp_socket, so we can be sure 'type' and 'ip_proto' are
always accessible through net_context API.
Remove 'type' and 'ip_proto' members from 'esp_socket' structure, as
those are already accessible by net_context API.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Change type of esp_socket->flags from uint8_t to atomic_t, so that read
and write access to those flags is done in atomic (thread-safe) manner.
Introduce esp_socket_ref() and esp_socket_unref() functions, which
operate on atomic refcount variable. esp_socket_ref() role is to
increase refcount if it was already non-zero. If it was zero then NULL
is returned, which means that socket is not used by net_context at the
moment.
Role of refcount:
* socket instance is assured to be between net_offload->get() and
net_offload->put() when refcount > 0,
* makes sure that socket instance can be used (its members can be
dereferenced) when refcount > 0,
* 'context' member is always valid and its members can be dereferenced
when refcount > 0.
esp_socket_get() gets unused socket, as previously. Additionally it sets
refcount to 1 at the end of call, which basically means that from that
point such socket can be referenced by other parts of the driver. Each
esp_socket_get() call should be followed by esp_socket_unref() and
esp_socket_put() to properly invalidate socket and prevent other parts
of driver from using it.
Add ESP_SOCK_WORKQ_STOPPED flag, which is now used to prevent scheduling
more work into driver workqueue. This flag is set in net_offload->put()
callback, so that no more socket work (such as processing RX/TX packets
or closing socket because of errors) is submitted after that.
Introduce mutex lock, which has following role:
* protects dst, connect_cb + conn_user_data, recv_cb + recv_user_data,
* assures that checking ESP_SOCK_WORKQ_STOPPED flag and actually
submitting (or not if net_offload->put was already called) new socket
work to workqueue is done in atomic way.
As there is a mechanism to prevent submitting new work items to
workqueue when net_offload->put() has been executed, then there is no
need to explicitly call esp_socket_ref() in esp_workq thread. This is
because one reference is being held by net_context (after calling
net_context->get()). This is why all the esp_socket_in_use() were simply
dropped. Code running from esp_rx thread on the other hand always uses
esp_socket_ref_from_link_id() helper function (which is backed by
esp_socket_ref()), so that it replaces previous esp_socket_in_use()
calls and additionally makes sure that socket stays valid ("in use")
until esp_socket_unref() is called.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added selection of MPU_ALLOW_FLASH_WRITE.
Using a flash driver while MPU is enable without
this option on doesn't make sense at all.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The DAC53608 and DAC43608 (DACx3608) are lowpower, eight-channel,
voltage-output, 10-bit or 8-bit digital-to-analog converters (DACs)
respectively. They support I2C with a wide power supply range
from 1.8 V to 5.5 V, and a full scale output voltage range of
1.8 V to 5.5 V. The DACx3608 also includes per channel, user
programmable, power down registers.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
ARM Server Base System Architecture defines Generic UART interface,
which is subset of PL011 UART.
Minimal SBSA UART implementation does not define UART hardware
configuration registers. Basically, only FIFOs and interrupt management
operation are defined.
Add SBSA mode to PL011 UART driver, so it can be used at SBSA-compatible
platforms, like Xen guest.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
The STM32 driver currently does not support reading a sequence of
multiple ADC channels. Only the first channel of the sequence was
read and the rest was silently ignored.
Fix: Return an error if reading multiple channels is requested.
Signed-off-by: Martin Jäger <martin@libre.solar>
Older LPC platforms use Flash IAP with a command style firmware command.
Tested on LPC54114 platform.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Currently, if no net_pkt's are available, the radio driver RX thread
drops the 802.15.4 frame silently. This causes undesired behaviour,
where we can drop the packet which has already been acknowledged at
the 802.15.4 level.
Fix this, by blocking the RX thread if no net_pkt is avaliable. The
packets received while the RX thread is blocked will be accumulated in
the underlying nRF 802.15.4 driver, and eventually when it runs out of
internal buffers before the thread is unblocked, it'll stop
acknowledging the incoming frames.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The flash shell can work with any flash driver instance, not just the
one chosen by zephyr,flash-controller. It's helpful for the flash shell
to use this instance by default, but not required. We can switch
instances at runtime with the "flash set_device" command.
Fix the flash shell so it can build when there isn't a chosen
zephyr,flash-controller available.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introduces a new flash driver for the FlexSPI peripheral on i.MX RT
SoCs. The hardware provides a flexible sequence engine (LUT) that
supports various types of external devices, including serial NOR flash,
serial NAND flash, HyperBus (HyperFlash/HyperRAM), and FPGAs. It
supports up to four connected devices in single/dual/quad/octal modes
and provides memory-mapped read/write access to these devices through
the AHB bus.
The driver implementation consists of a shared controller for each
FlexSPI peripheral instance, and protocol-specific device drivers for
each external device. The controller provides a private interface for
multiple devices to access the FlexSPI peripheral registers. FlexSPI
devices provide the public flash driver interface to applications or
subsystems like storage or flash file systems; they also provide
protocol-specific LUT sequences to the controller.
Currently the only device type supported is QSPI NOR flash, but other
types like HyperFlash will be added later.
XIP is not yet supported, as this requires additional work to relocate
code to RAM and managing interrupts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This wait on @ prompt was added in
fa3d586483.
The situation were the @ prompt is never received should not occurs,
however it's definitively safer to catch it instead of having a
deadlock.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
Remove conditionals (PM_DEEP_SLEEP_STATES and PM_SLEEP_STATES) from
power management code. Now these features are always available when
power management is enabled.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Migrate the whole pm subsystem to use new power states information
from power_state.h and get states and residency properties from
device tree.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
So far a dedicated FIFO was used for all RX packets, which was consumed
in single submitted work. This work was also responsible for closing
socket and notifying uppper network layers if some errors occurred
previously or socket was simply closed by peer. There is however a
potential race condition in scenario described below:
esp_rx thread | esp_workq thread
--------------------------|-----------------------------
| ---- esp_recv_work ----
| handle RX packets from FIFO
|
---- on_cmd_ipd ---- |
put new RX packet to FIFO |
---- on_cmd_ipd ---- |
|
---- on_cmd_closed ---- |
mark socket as closed |
---- on_cmd_closed ---- |
|
| handle close
| ---- esp_recv_work ----
In this case we assume that esp_workq was preempted just after
processing all RX packets from FIFO and before checking if socket was
closed. In such scenario RX packet put to FIFO just before doing close
is going to be unhandled, so application layer will miss part of the
data.
Change the way RX packets are scheduled to workqueue, by using the
already available net_pkt->work objects (used for example in native TCP
stack). Create a separate work for closing connection. As a result all
RX packets and close handlers are on the same queue and there is no risk
of handling close events before handling all previously received data.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There might be some scheduled work related to socket currently requested
to be destroyed/closed. Schedule a dummy work to make sure all
previously running work items in workqueue are finished.
When talking about TX packets, this makes sure that all previously
scheduled data is actually sent (flushed) before closing socket.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
It is enough to initialize work structures once during driver init,
because work handlers do not change during driver lifetime.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Currently there are two code paths when sending packets:
asynchronous (using workqueue) when zero timeout was specified and
synchronous in other cases. This doesn't seem to be justified, so
convert code to always schedule packet sending using workqueue.
Each net_pkt has an embedded work item, so use it instead of esp socket
specific work that was shared across all sent packets. This gives a
possibility to schedule multiple packets for sending.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Callback and user data are saved in net_context structure. Those members
are used by native networking stack (net_if), so simply follow the same
pattern.
First of all this allows to reduce runtime information for driver socket
instance. Second and most important benefit is that it allows to move
send handling entirely to workqueue thread.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
TICKLESS_CAPABLE is now selectable only and without prompt, so remove it
from _defconfig files and select it directly by the timer.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
z_timer_idle_enter is declared only when CONFIG_TICKLESS_IDLE is
selected. This function is not implemented anywhere, but the only
driver including this header is not TICKLESS_CAPABLE. So, no undefined
reference will happen.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Use TX FIFO level interrupt if available in hardware. It matches the
Zephyr UART API and avoids "bootstrapping" which is needed when using
the TX edge interrupt ("TI"). TX FIFO has room for up to 32 characters
and will typically reduce the number of interrupts.
Details:
APBUART can be synthesized with or without support for TX/RX FIFO.
Edge interrupts which fire when TX holding register changes and RX data
available are always available, independent of the FIFO configuration.
If FIFO is made available at synthesis time, two additional interrupts
become available: TX FIFO half-empty and RX FIFO half-full. These
are level interrupts.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
This commit aligns the GRLIB APBUART driver with the Zephyr UART API
and fixes an issue where TX interrupt could previously be lost. It
was typically seen during interactive operation in the Zephyr shell.
There is an expectation in the Zephyr UART API that TX ready (i.e. TX
buffer space available) interrupt is a level interrupt, i.e. always
active while there's TX buffer space available. In particular, there's
an expectation that after uart_irq_tx_enable(), the TX interrupt will
immediately fire (assuming free TX buffer space is available).
The APBUART "Transmitter interrupt (CTRL_TI)" does not directly fulfill
this expectation because it is edge triggered and fires when the TX
holding register moves from being non-empty to empty. The solution
is to "bootstrap" interrupt processing by calling user-defined ISR
in irq_tx_enable().
This fix is similar to commit 49bb163756 ("drivers: serial:
uart_cmsdk_apb: Fix interrupt-driven operation").
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
The driver allocated packet from the TX pool on its RX path. Fix this
by using a correct allocator function.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
ESP chip send number of available RX data using
+IPD=<sock>,<avail_bytes> command. This exact number (truncated to MRU)
was used to read data with AT+CIPRECVDATA=<sock>,<num_of_bytes>.
Use always MRU when sending AT+CIPRECVDATA=<sock>,<mru> request. When
there are less bytes available, then +CIPRECVDATA will just return less
bytes, which is fine for the driver.
There are two advantages to this new behavior:
* there is no need to follow how many bytes were notified by +IPD
message, thus reducing implementation size,
* when data is constantly received by ESP chip, then the last number of
bytes notified by +IPD is no longer up-to-date when sending a
AT+CIPRECVDATA; always requesting MRU number of bytes allows to
always receive maximum currently available number of bytes buffered
by ESP chip.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Dump of communication between ESP chip and Zephyr shows that
+IPD:<sock>,<bytes_avail> is always received after +CIPRECVDATA. This
means that we don't need to update sock->bytes_avail in esp_workq
thread. Additionally there is no need to schedule next AT+CIPRECVDATA
request, as that will be done by +IPD handler anyway.
Relying on +IPD to be received after each +CIPRECVDATA (as long as there
is some more data to be received) allows to simplify operations on
sock->bytes_avail. From now on only esp_rx thread will update its value
and schedule AT+CIPRECVDATA in esp_workq thread. Then in
sock->bytes_avail will be treated as "readonly" in esp_workq
thread. This allows to prevent race condition when both esp_rx and
esp_workq threads could potentially update value of sock->bytes_avail
value at the same time.
<sock>,CLOSED message is received always after retrieving all data from
ESP chip (using AT+CIPRECVDATA), so there is no need to check whether
there are more bytes to be received before marking socket as closed in
Zephyr driver.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add extra error data information to callback parameter. Add tests for
testing the data provided.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Split setting EDAC IBECC ctrl to setting error_type and
error_trigger to make it easier for other platforms.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Replace addr with param1 and addr_mask with param2 for get / set types
of functions. Those names are more general and allow to implement
error injections for other platforms.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add an emulation controller which routes eSPI traffic to attached
emulators depending on the selected chip(mostly host).
This allows drivers for eSPI peripherals to be tested on systems
that don't have that peripheral attached, with the emulator handling
the eSPI traffic.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
The default configuration is made to be "master" at
"standard speed". This makes it possible to use the
driver without having to configure it.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Enable slave support for I2C device instances. Slave mode is
interrupt based, wheras master mode is still based on polling.
Remove ENI bit in master configuration since it is not needed for
master mode.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Initial driver and sample application of
TDK Invensense ICM42605 6-axis motion sensor.
This driver provide DTS for nRF52 DK board DTS setting.
Providing features are below.
Sensor data streaming - Accel, gyro
Tap, Double tap triggering.
Set/Get FSR, ODR by set attr API
Support multi instance feature.
Signed-off-by: JuHyun Kim <jkim@invensense.com>
Move i2s_cavs_irq_connect_##n up so its available later when used. This
fixes compile issues with the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit verifies if the mac configuration is done correctly
during liteeth setup, and prompts a warning when not.
Signed-off-by: Pawel Sagan <psagan@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commit eliminates an inifite waiting for the TX ready flag
in the eth liteeth driver, exiting with error after a defined
number of attempts.
Signed-off-by: Pawel Sagan <psagan@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This patch adds support for Microchip's KSZ8794 DSA device, which for
switch and PHY control uses SPI communication.
This driver also provides support for handling tail tagging added and
decoded in the KSZ8794 device as well as modifying entries in the
static MAC address table.
It is also possible to use GPIO pin to reset KSZ8794 switch.
When the "reset-gpios" property is not defined, software based reset
is performed instead.
The KSZ8794 can now be used on boards which have SPI CS only available
as GPIO pin.
Signed-off-by: Stefan Bigler <stefan.bigler@securiton.ch>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch modifies Bluetooth HCI RPMsg drivers and samples to use
RPMsg Service instead of configuring OpenAMP directly in the driver
or the sample.
Co-authored-by: Piotr Szkotak <piotr.szkotak@nordicsemi.no>
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
Introduce a Kconfig variable that the SoC can set to indicate the
number of instances in Device Tree. This also fixes the accuracy of
the Elkhart Lake instance count where the code was previously assuming
up to 12 instances even though DT lists 15 nodes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move all PCIe-based DT nodes under a PCIe bus and take advantage of
the DT_ANY_INST_ON_BUS_STATUS_OKAY() and DT_INST_ON_BUS() macros.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove DW and PCA9685 PWM controller drivers as they are unmaintained
and broken.
Both drivers lack support for the pwm_get_cycles_per_sec_t API function
which was introduced in commit 56e0b53c6e
in 2016.
Fixes#18607, #18608
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This commit add support for i2c on imx6sx.
I2C support is based on imx7d and requires NXP HAL.
The Device Tree binding is also changed to better reflect that i2c
driver support both imx6sx and imx7d.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Add PAX[PCIE<->AXI] DMA driver which supports DMA
transfers between host and target memory over PCIe link.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Refactor slightly so we can read SFDP tables with this driver. Note
that the SFDP read command requires long frame mode transfers as data
exceeds 8 bytes.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
QSPI doesn't have a different length expectation than normal SPI, so
introducing a new name for an existing name is unnecessary. Also
replace the constant with the actual buffer size where appropriate, in
somebody changes the the buffer definition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Kconfig allowed selecting any bit in the status register as the QE
bit, and defaulted it to 6. Devices need not require a QE bit at all,
and where JESD216 defines QE bit location the only place in first SR
byte that it can be is bit 6. Further, the code unconditionally wrote
the value 0x40 without respecting configuration of other bits. Some
of those bits control write protection of block-protected areas and
should not be changed.
Remove the Kconfig, instead using the jedec,jesd216-controlled
devicetree property. Allow the driver to recognize whether or not
setting the bit is required, and when it is only use bit 6. Only
update if the setting does not match the configuration.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The interface used to send commands supports only a command followed
by 8 bytes of data transfer. Reject attempts to do more, as the
result will be a successful transfer of only the first 8 bytes.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Not all special commands require that a write-enable be issued first.
Allow the caller to decide.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW16 provides information on mechanisms to enter and exit 4-Byte
address modes, returning the device to reset state, and how to
manipulate the values in the first status register.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW15 provides information on entry and exit from QSPI modes. In
particular, it specifies whether and how the status register must be
updated for this feature.
Add a JESD216 devicetree property for the Quad Enable Requirements
value.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Instead of having a hard-coded maximum instance count, introduce a
Kconfig variable for it. The inclusion of the per-instance header
files is solved by having them chain-include each other with a
pre-processor condition that checks if the current header file is the
last one or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The reg-shift support was quite broken in that the code only looked
for this property on instance 0. Now we support the property on any
node which might declare it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Take advantage of DT_INST_FOREACH_STATUS_OKAY() to look for DLF and
PCP properties on any matching nodes with "okay" status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use a dependency block instead of specifying a UART_NS16550 dependency
for each individual opton. This doesn't save many lines right now, but
may do so once more options are added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The existing method of testing for any of the first four DT instances
having the pcie property feels a bit clumsy and will get more so when
support for more than four UARTs is added. A much more cleaner way to
do this (and more correct probably as well) is to list any PCIe-based
UART nodes under a pcie bus in the Device Tree hierarchy.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Part of GPIO pads in npcx series support low-voltage (1.8V) level
detection. In order to introduce this feature, this CL adds a new
NPCX-specific controller property, lvol_io_pads, in devicetree file.
For example, here is devicetree fragment which turn on low-voltage
support of i2c1_0 port.
/ {
def_lvol_io_list {
compatible = "nuvoton,npcx-lvolctrl-def";
lvol_io_pads = <&lvol_io90 /* I2C1_SCL0 1.8V support */
&lvol_io87>; /* I2C1_SDA0 1,8V support */
};
};
Then these pads will turn on 1.8V level detection during initialization.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add initial implementation of the uart async api
for stm32 mcus. This uses the dma controller
in normal mode for reception. In addition, to detect
reception of bytes we enable the idle line detection
interrupt.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Signed-off-by: Jun Li <jun.r.li@intel.com>
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Firmware implementing the PSCI functions described in ARM document
number ARM DEN 0022A ("Power State Coordination Interface System
Software on ARM processors") can be used by Zephyr to initiate various
CPU-centric power operations.
It is needed for virtualization, it is used to coordinate OSes and
hypervisors and it provides the functions used for SMP bring-up such as
CPU_ON and CPU_OFF.
A new PSCI driver is introduced to setup a proper subsystem used to
communicate with the PSCI firmware, implementing the basic operations:
get_version, cpu_on, cpu_off and affinity_info.
The current implementation only supports PSCI 0.2 and PSCI 1.0
The PSCI conduit (SMC or HVC) is setup reading the corresponding
property in the DTS node.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Move iis2dlpc trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Simplify the switch case on trigger types (SENSOR_TRIG_DRDY and
SENSOR_TRIG_TAP) inside iis2dlpc_enable_int().
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch replace CONFIG_GPIO_SIFIVE_N_PRIORITY into interrupt-cell
of device-tree to set IRQ priority.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
This patch replace CONFIG_UART_SIFIVE_PORT_0_IRQ_PRIORITY into
interrupt-cell of device-tree to set IRQ priority.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
In #31192 stm32 uart driver uart_irq_rx/tx_ready functions were
modified to take into account status of irq.
While it seems wlecome for TX (based on uart client's implementation),
this is not correct for RX.
Revert change in uart_stm32_irq_rx_ready function.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace marco function, defined(), with IS_ENABLED() in host sub-devices
driver implementation. In this PR, we won't replace the macros which
cause -Wimplicit-function-declaration warning if related configuration
is not enabled or its type is not boolean..
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
In npcx7 series, the Timer and Watchdog module (TWD) generates the
clocks and interrupts used for timing periodic functions in the system.
It also provides watchdog reset signal generation in response to a
failure detection.
The CL also includes:
— Add npcx watchdog device tree declarations.
— Zephyr watchdog api implementation.
— Add Watchdog definitions for npcx7 series in
tests/drivers/watchdog/wdt_basic_api/src/test_wdt.c for
supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This commit is about the it8xxx2 i2c master driver which
includes six SMBus channels. The enhanced channel i2c3,
i2c4, i2c5 are controller which are designed to support
the I2C protocol.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
In order to ease reuse on other series, set DMA as optional
and use IT if no DMA channel is specified in the qspi node.
Tested on disco_l475_iot1
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for DMA based STM32 QSPI NOR flash controller.
Driver configures both NOR flash and also QSPI hardware block.
Reuses existing jesd216 library.
QSPI hardware block handling is done through the use of Cube HAL API.
This requires the use of HAL interface also for DMA besides zephyr
DMA driver.
Zephyr DMA driver is used only for IRQ routing while HAL driver
handles the IP block. To achieve this it is required to:
-Configure both Cube and Zephyr drivers at init.
-Inform Zephyr driver that current channel handling will be done
by another instance and only a limited configuration should be done.
For this last part, a unused parameter is overridden in order to
transmit the information.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
In preparation for QSPI DMA mode:
-Add a possibility to override driver by the HAL DMA. In that case
stream is set as busy and no configuration nor treatment is done.
In case of interrupt, flags clearing is let to HAL.
-Treat Half Transfer interrupt prior to Transfer Complete for the
cases were both IRQ are both raised at the time IRQ handler is called
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
AHB3 bus support is added for compatible series.
Additionaly, fix condition for AHB2 support and fix
formatting
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Now that we generate a header that extern's all possible devicetree
based device struct we can remove DEVICE_DT_DECLARE and
DEVICE_DT_INST_DECLARE as they aren't needed anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
According to AT commands manual, no wait after prompt '@'
is required if using AT+USOST commmand (aka. sendto,
only used with UDP).
Signed-off-by: Emil Lindqvist <emil@lindq.gr>
core-macros.h includes other files not part of the xtensa HAL, make this
esp32 specific
Fixes#31301
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Disable RTC WDT enabled (by default) by 2nd stage bootloader in ESP-IDF.
This WDT timer ensures correct hand-over and startup sequence from
bootloader to application.
Enabling bootloader caused system clock initialization to fail
when clock rate is greater then 80MHz. This also fixes
esp32 clock source code.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
-The STM32F410RB has no AHB2 bus so LL_AHB2_GRP1_EnableClock() and
LL_AHB2_GRP1_DisableClock() should not be called for this soc.
-The interrupt table had to be changed because of no OTG_FS_WKUP_IRQn
(no USB OTG at all).
Signed-off-by: Hans Unzner <hansunzner@gmail.com>
Convert the driver so that it creates its instance basing on DT.
Remove no longer needed Kconfig option CRYPTO_NRF_ECB_NAME.
Also update accordingly the crypto sample.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Since the PU power rail of i2c bus might be gone at the initial state
after ec powered up, we might have no chance to get STOP condition. This
is because no i2c transactions occurred before its power rail is
restored. But it's crucial to reset the whole i2c module after i2c bus
is back to the idle state.
The original test suite for i2c recovery mechanism didn't consider this
case that initial i2c bus is low before ec powered on. Hence, this CL
fixed this symptom by:
1. Force i2c modules must proceed 'reset' step no matter we received
STOP condition or not.
2. Use Boolean for condition check to prevent misusage and meet MISRA.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Extend the PWM API with optional API functions for capturing PWM pulse
width and period cycles.
Fixes#26026.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for enabling and configuring PLL3 on STM32 H7 series. PLL3
is used as a clock source by certain peripherals, e.g. LTDC.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Provide a utility function to compute PLL VCO input range so that it
can be re-used for other PLLs.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
When flash is Dualbank and flash size is lower than 512K,
then there is a discontinuity between bank1 and bank2.
Also take into account bank swap capability.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
When setting baudrate register, baudrate value is computed according
to the oversampling given value, which is default boot time
value (16).
In case oversampling value has been changed by bootloader (as in case
of TFM bootloader), a desynchronsation happens between OVR and BRR
values and the ouptut baudarate is incorrect.
For oversampling register before setting the baudrate to avoid this
situation.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When calling irq_rx_ready or irq_tx_ready API, return the logical AND
between the irq status and the enable of that irq.
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
In order to simplify the handling of DMA_STM32_V1/V2 and DMAMUX_STM32
symbols, set them directly based on related compatible status.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2 versions of DMA hardware blocks could be found across stm32 series.
In order to simplify the handling of matching Kconfig symbols,
make this visible in dts files by creating "st,stm32-dma-v1" and
"st,stm32-dma-v2" and set them accordingly in dtsi files.
Duplicate and update related bindings to reflect that new state.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
1. don't use "inline" in .c, let the compiler decide
2. remove superfluous parentheses
3. simplify a function by directly returning the result of a boolean
operation
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Some interrupts can be enabled by the ROM, e.g. the timer interrupt.
When then in Zephyr the interrupt controller is enabled, before
individual interrupts are configured, interrupts can arrive and lead
to the spurious interrupt handler being invoked. Fix thid by
disabling all child interrupts when configuring cAVS interrupt
controllers.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Line break on #error directive is confusing github and ending up
breaking syntax highligthing in github UI which makes me nervous
during review.
Convert error message to a one liner.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Due to clock discrepancy, busy waiting for 15us was not covering for
half tick in certain cases. Busy wait runs from HF clock source.
Increased to 19us to cover it. Anyway, this case is hit very rarely,
only when there was aborted, not-cancelled compare value that was
about to expire. Because of that, increase shall not impact the
performance.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
For historical reasons, the maximum speed of the Atmel SAM USB
controller is done by comparing the maximum-speed property string from
the DT using strncmp at runtime.
Now that the DT_ENUM_IDX macro exists, we can use it to get the
maximum-speed property at build time and without string comparison.
Unsupported speed can also be reported at build time.
Note that the default speed in case the optional maximum-speed property
isn't present in the DT is changed from full-speed to high-speed to
match the property description. This is a no-op in practice as this
properties is defined at the soc level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
CAN_MCP2515_MAX_FILTER is not needed anymore and was probably just a
misunderstanding. Aligned it with the other CAN drivers.
This also was the last difference in the mcp2515 specific config for the
can sample, so that can be deleted as well.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The STM32F105xx USB clock goes through a prescaler either PLL1 x2 /2
or PLL1 x2 /3, the output of this must be 48 MHz. As such, the output
of PLL1 must be 48 MHz or 72 MHz.
NOTE: This requires that the system is running from PLL1 (PLLCLK).
Support for running from PLL2 will be implemented in the future.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Set the prescaler in register BTR according to the configured bitrate in DTS.
This bug appeared in commit 8b6c1bd4b7
Signed-off-by: Julien D'Ascenzio <julien.dascenzio@paratronic.fr>
```
/home/humanentity/zephyr/drivers/ipm/ipm_handlers.c:23: undefined reference to 'z_impl_max_data_size_get'
```
The error shows when having CONFIG_BT=y and CONFIG_USERSPACE=y, and
is easily reproduced by adding
```C
CONFIG_USERSPACE=y
```
to `samples/bluetooth/peripheral/prj.conf` and building the sample.
E.g.
```
$ west build -p auto -b nrf5340pdk_nrf5340_cpuapp samples/bluetooth/peripheral
```
Signed-off-by: Peter Andersson <pelleplutt1976@gmail.com>
Retain the assumption that the loop will assign a pointer, but
initialize it pointer first to eliminate build warnings.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Remove all odr values from Kconfig and always init it
at 12.5Hz. It is responsibility of application to set
the rate to a different value using SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adds support for ADC on G0 series.
Simple implementation: sequencer not fully configurable,
and only one common sampling time.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The Bluetooth receiving thread may not be able to process broadcast
packets because the system API(bt_hci_cmd_send_sync) is in block state.
If HCI driver is still waiting buffer for adv report, an assertion will
be triggered.
Fixes: #30955
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
z_free_fd() is called twice then you close(). For example in ublox sara
r4 driver offload_close() calls modem_socket_put() where z_free_fd() is
called first time. Then this same function is called another time in
socket.c in z_impl_zsock_close() after this function has called
offload_close() in ublox sara r4 driver. This causes socket
descriptor leak.
Fixes#26819
Signed-off-by: Akseli Peltola <peltsu1324@gmail.com>
Flash size is specified in bits by SFDP and devicetree, but the stored
flash size is in bytes. Correct the divisor.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This patch adds the driver for Omnivision OV7725
Color CMOS VGA Sensor.
The driver currently provides a simple capture
function, the output format only provides
RGB565,640x480.
Signed-off-by: Frank Li <lgl88911@163.com>
This patch enables the rtc clock on the stm32g4 soc
from STMicroelectronics.
Even if the set by default (reset value of theRCC_APB1ENR)
the bit is marked as 1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
After system reset, the PWR interface clock must be enabled
by setting the PWREN bit of the RCC_APBENR1
This sequence is needed to use the RTC.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This converts the intel_gna driver to use device tree instead of
kconfig for device configuration.
Fixes#30872
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The thresholds for activity/inactivity in the adxl362 acceleromter have
two parameters that can be configured. Currently the threshold is
configurable via the KConfig variables CONFIG_ADXL362_ACTIVITY_THRESHOLD
and CONFIG_ADXL362_INACTIVITY_THRESHOLD which configure repectively the
value in the THRESH_ACT and THRESH_INACT registers.
The other parameter that can be configured is the time by changing the
values in the registers TIME_ACT and TIME_INACT, but this values are
hardcoded to 1 (see lines 653 and 675 in adxl362.c), this patch adds
support for configuring those values in KConfig as
CONFIG_ADXL362_ACTIVITY_TIME and CONFIG_ADXL362_INACTIVITY_TIME.
Signed-off-by: Xavier Naveira <xnaveira@gmail.com>
Change switches to using static memory for out endpoints. Using
heap is not necessary, because number of out endpoints is defined
in DTS.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Add a new display-inversion property to ili9xxx based display drivers to
send a "Display Inversion ON (0x21)" command during initialization.
This seems to be required for some ILI9xxx based displays to work
correctly, such as BuyDisplay ER-TFT028A2-4 (ILI9341 basd IPS display).
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
It is possible to use the UART abstraction for USB communications
without any of the dedicated UART drivers being enabled. This currently
causes a compilation error because CMake throws an error if a library
has no sources. The empty file forces there to be at least one file in
the library when `CONFIG_USB_CDC_ACM` is enabled.
Removing `select CONFIG_SERIAL_HAS_DRIVER` from `CONFIG_USB_CDC_ACM` is
not a valid solution as this symbol is required by `CONFIG_UART_CONSOLE`
and therefore `USB_UART_CONSOLE`.
Fixes#31067.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Need to declare the device before the pointer can be obtained, and to
validate the device before trying to use it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
For a while now, we've had two APIC drivers. The older was preserved
initially as the new (much smaller, "new style") code didn't have
support for Quark interrupt handling. But that's long dead now. Just
remove it.
Note that this migrates the one board using this driver (acrn) to
CONFIG_APIC_TIMER instead.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This change adds support for configurable interrupt capabilities
in the emulated GPIO controller via Devicetree bindings.
Fixes#26477
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
The NPCX SMB modules provides full support for a two-wire SMBus/I2C
synchronous serial interface. Each SMBus/I2C interface is a two-wire
serial interface that is compatible with both Intel SMBus and Philips
I2C physical layer. There are 8 SMBus modules and 10 buses in NPCX7
series.
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller) Please refer Section 4.7.2 in the datasheet. In order to
support it, this CL seperates the i2c driver into port and controller
drivers. The controller driver is in charge of i2c module operations
and internal state machine. The port driver is in charge of pin-mux
and connection between Zehpyr i2c api interface and controller driver.
All of modules have separate 32-byte transmit FIFO and 32-byte receive
FIFO buffers. These FIFO buffers reduce firmware overhead during long
SMBus transactions by allowing the Core to write or read more than one
data byte at a time to/from the SMB module.
The CL also includes:
— Add npcx i2c port/controller device tree declarations.
— Zephyr i2c api implementation.
— Add "i2c-0" aliases in npcx7m6fb.dts for i2c test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The System Glue module includes the three major functions:
— Power Switch Logic (PSL)
— SMBus multi-bus, wake-up support
— Simple Debug Port (SDP)
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller). Since a single SMB module is able to serve only one
SMBus/I2C bus at a time, SMB_SEL registerin Glue module is used to
control theconnection of I2Cn_0 and I2Cn_1 interface pins to the SMBn
module (where n is 5, 6).
This CL provides a soc specific pin-control function called
"soc_pinctrl_i2c_port_sel" to switch buses (port) of the same SMB module
(controller). It will be used in the following i2c driver.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This CL add a new notification event, ESPI_PERIPHERAL_EC_HOST_CMD, and
two response opcodes, ECUSTOM_HOST_CMD_GET_PARAM_MEMORY and
ECUSTOM_HOST_CMD_SEND_RESULT, to connect with host command sub-system
between host and ec.
It also introduced three configurations to increase the flexibility of
ec host command settings:
1. ESPI_PERIPHERAL_HOST_CMD_DATA_PORT_NUM:
Host I/O peripheral port number for ec host command data. The default
value is 0x0200.
2. ESPI_PERIPHERAL_HOST_CMD_PARAM_PORT_NUM:
Host I/O peripheral port number for ec host command parameters. The
default value is 0x0800.
3. ESPI_NPCX_PERIPHERAL_HOST_CMD_PARAM_SIZE:
Host I/O peripheral port size for ec host command in npcx series. The
valid value in npcx ec series for this option is
8/16/32/64/128/256/512/1024/2048/4096 bytes. The default value is 256
bytes.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces two kinds of op codes for espi_api_lpc_read_request
and espi_api_lpc_write_request Zephyr espi api functions.
One is for supporting ACPI and shared memory region to access ACPI data.
The other is customized for certain platforms such as Chromebook and so
on.
This CL also introduced the following configurations to add the
flexibility of these settings.
1. ESPI_PERIPHERAL_ACPI_SHM_REGION_PORT_NUM:
Host I/O peripheral port number for shared memory region. The default
value is default 0x0900
2. ESPI_NPCX_PERIPHERAL_ACPI_SHD_MEM_SIZE:
Host I/O peripheral port size for shared memory in npcx series.
Please notice the valid value in npcx ec series for this option is
8/16/32/64/128/256/512/1024/2048/4096 bytes. The default value is 256
bytes.
This CL also turn off hardware-wire feature which generates VW events
that connected to hardware signals such as SMI and SCI. We will set
VW output events directly via espi_api_send_vwire() api function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
TMP117 from TI is a sensor similar to tmp116, but it has more precision
and it also supports the offset register.
Add support for SENSOR_ATTR_OFFSET, which is used by TMP117 to the
pre-exisiting tmp116 driver.
This commit also enables multiple instances and adds TMP117 to Kconfig.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Add `get_status` function to dmamux driver api.
This uses the regular dma driver `get_status` function.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
off_t can be 32-bit or 64-bit depending on the platform. STM32 flash
addresses are always 32-bit so it's safe to use long here.
Signed-off-by: Martin Jäger <martin@libre.solar>
Convert drivers to use pinmux devicetree node to create pinmux device
object.
On intel S1000 we add 'label' as a required property and set it to
'PINMUX' to match CONFIG_PINMUX_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert drivers to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert soc nios2 qspi to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert intel gna driver to DEVICE_DEFINE instead of
DEVICE_AND_API_INIT so we can deprecate DEVICE_AND_API_INIT in the
future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NRFx IPC to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert LED PWM driver to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This converts the i2s_cavs driver to use device tree
instead of kconfig for device configuration.
Fixes#30750
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use a similar model to the pinmux_rv32m1 driver for kinetis pinmux
driver. We handle one subtle difference between clock on the KE1xF v
other SoCs.
As the Kconfig and devicetree label names are the same we maintain the
Kconfig options in the driver until all board users are converted over
to use devicetree instead of Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add an additional 4 ports for upcoming Arm based server that will have a
total of 12 I2C ports.
Similar to the original 8 ports, these additional 4 ports will not be
enabled unless specified at configuration time.
Signed-off-by: Dan Kalowsky <dkalowsky@amperecomputing.com>
The STM32L0 series MCUs have quite basic timer features only, so we
remove some unavailable configuration options. They were properly
initilized by the LL StructInit functions for other MCUs anyway.
Signed-off-by: Martin Jäger <martin@libre.solar>
