Add STM32C0 SOC to combined interrupt config in order to
make it support the I2C driver.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Tickless idle has been replaced by the tickless kernel and also power
management has become much more advanced.
See also: https://github.com/zephyrproject-rtos/zephyr/pull/33302
Signed-off-by: Manoel Brunnen <mb@lee-brunnen.de>
Add implementation of the Telephony and Media Audio Service, as well as
two sample applications.
tmap_central reflects a smartphone implementing the Unicast Media Sender
and Call Gateway TMAP roles.
tmap_peripheral reflects an earbud implementing the Unicast Media
Receiver and Call Terminal TMAP roles.
Upon connection, tmap_central starts an audio stream using CAP Initiator
APIs.
CCP, MCP and VCP are discovered and used to send example commands.
Future improvements: 2-earbud support, add TMAP Broadcast roles,
update with new CAP Acceptor/Commander APIs as they become available
Signed-off-by: Silviu Petria <silviu.petria@nxp.com>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
atomic_inc(&buffered_cnt) return previous count of log messages,
should use current count to compare with threshold config value.
Signed-off-by: Dong Wang <dong.d.wang@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
This patch modifies intel_adsp_ipc_is_complete function so it don't
report that IPC is completed when we are still waiting for ACK from
HOST.
This change will allow to solve the problem that occurs during the power
state transitions. Occasionally, the Application decides to enter the
power gating state after sending an IPC message, before receiving an ACK
from the HOST. This results in broken IPC communication when coming back
to Idle state.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Bluetooth mesh had many groups defined as top level Doxygen groups.
Place all of them to `bt_mesh`. Also removed redundant `@brief` entries,
and placed the block at the right location (just below extern "C"
entry), as well as uniform spelling of "Mesh".
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
According to RFC768 UDP packets with zero checksum are allowed with IPv4.
Enable this by default.
For example, some routers use zero checksum in DHCP packets.
Signed-off-by: Nils Ruf <nils.ruf@endress.com>
Enable i2c pullups in the nrf52dk overlay
Without this, the first I2C transaction after reset can be corrupted
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
The current approach of failing the build on ztest with no optimization
broke coverage builds, and generally raised some concerns about being
too aggressive.
Downgrade the error to a warning and rework the option to inhibit the
warning, while also dropping it automatically for POSIX (that are not
really affected by stack size) and coverage run (that always runs with
no optimization).
Will reconsider this down the road if we still see issues filed for the
tests broken with no optimization and no further tuning.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix compiler warnings in the UART emulator header file. By explicitly
adding the include for the Zephyr device.
Signed-off-by: Oscar Goldring <oscar@goldring.dev>
Update release notes 3.4 with description of
EXTRA_CONF_FILE, EXTRA_DTC_OVERLAY_FILE, and EXTRA_ZEPHYR_MODULES.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Update Zephyr modules documentation to use EXTRA_ZEPHYR_MODULES.
This gives a more consistent naming scheme in Zephyr CMake build system.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Align Zephyr modules with other user facing variables where settings
can be defined or extended, meaning Zephyr modules now supports:
ZEPHYR_MODULES and EXTRA_ZEPHYR_MODULES.
Support for ZEPHYR_EXTRA_MODULES is kept foir backward compatibility.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Introduce EXTRA_CONF_FILE and EXTRA_DTC_OVERLAY_FILE and remove old
references to OVERLAY_CONFIG.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Align sysbuild with Zephyr CMake so that sysbuild supports
SB_EXTRA_CONF_FILE. Keep support for the old SB_OVERLAY_CONFIG.
This ensures that sysbuild is consistent with Zephyr CMake configuration
file handling.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Update package_helper.cmake to use EXTRA_CONF_FILE instead of deprecated
OVERLAY_CONFIG variable.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This commit introduces EXTRA_DTC_OVERLAY_FILE.
This allows users to specify additional devicetree overlays in addition
to a sample / board specific default devicetree overlay files.
It also allows snippets to provide extra devicetree overlays on addition
to sample / board specific overlays.
The name EXTRA_DTC_OVERLAY_FILE clearly indicates the purpose and
follows the naming scheme of EXTRA_ in front of variable name.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This commit introduces EXTRA_CONF_FILE and deprecates OVERLAY_CONFIG.
It has often caused confusion that OVERLAY_CONFIG adds extra
configuration fragments to the value of CONF_FILE (default: prj.conf),
but the similar named variable DTC_OVERLAY_FILE replaces the default
dtc overlay file used by the build system.
To remove such confusion, this commit introduces the EXTRA_ prefix in
front of CONF_FILE to clearly indicate it's purpose.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This commit extends zephyr_get() to support multiple variable names to
be fetched into a single variable.
Example:
zephyr_get(FOO VAR FOO_A FOO_B FOO_C)
will lookup each FOO_A, FOO_B, FOO_C for supported scopes and return
the value in FOO of the first scope encountered having one of the
variables defined.
If MERGE is specified, then all scopes for all vars are looped and the
variable values are merged into FOO and returned.
This functionality will allow to deprecate user-facing settings while
ensuring that both the new and deprecated variables are considered
in zephyr_get() and also taking into consideration the scope with
highest precedence.
This allows Zephyr CMake to do:
zephyr_get(FOO VAR FOO DEPRECATED_FOO)
zephyr_get(BAR MERGE VAR BAR DEPRECATED_BAR)
This allows support of old and new setting for a given number of
releases.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This is usually needed for reliable SPI communication when SCK
frequency is >= 4 MHz, so make it the default setting.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
- remove deprecated `label` properties
- add `spi-flash0` alias
- correct `sfdp-bfp` property value to reflect exactly what is returned
by the flash chip
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Changes the warning from being text in Kconfig for filesystem
management as a whole to being a cmake warning which is displayed
if the user has not enabled file access hooks with a link to the
documentation on how to set them up.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add a config to decide if a new dedicated thread for Host Command is
created during initialization.
If not, the ec_host_cmd_task has to be called by another thread to
handle host commands.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add a new _test_ that is used to build all regulator drivers. SoC
regulators, such as Raspberry Pi Pico core supply are excluded as they
are typically built as part of the platform.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The mcumgr subsystem as a whole is already maintained by @nordicjm
(#57780) and I am no longer actively using mcumgr, so removing myself
from the equation and letting more capable hands take over.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
The function nrf_reset_network_force_off contains workaround for
errata 161 for nRF5340 SoC. This function should be used instead of
manual writing to NRF_RESET->NETWORK.FORCEOFF register.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
The command at most takes 11 args. argc = num of args + 1 (command
name) => 12. We substruct 3 from argc (cmd name, mod id, addr). This
gives argc = 9 when all args are provided for vendor model.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
