pb gatt server starts fast advertising for the first 60 seconds.
After that, server goes into slow mode.
When pb gatt and pb adv work in parallel pd gatt changes fast to
slow modes after the first tx frame in pd adv (about 110ms)
since they both are handled in the same thread.
Actually, pb gatt never worked in fast mode
if pb adv was enabled (in most configuration cases).
Signed-off-by: Aleksandr Khromykh <Aleksandr.Khromykh@nordicsemi.no>
Logging v1 has been removed and log_strdup wrapper function is no
longer needed. Removing the function and its use in the tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
uuid wasn't initialized in the publication setting command.
It caused wrong the configuration clietn behavior.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
Introduce configuration options for chosen RPL implementations.
This will allow introducing alternate persistent storage schemes
for the replay protection list.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
`bt_mesh_rpl_check` stops iterating `replay_list` if either it found an
entry with the requested source address or unassigned address. When IV
index updated, `bt_mesh_rpl_reset` is called. It will set `old_iv` to 1
for all entries with fresh IV index and remove entries with old IV index.
If the entries with old IV index are mixed with other entries, this will
cause fragmentation of `replay_list`. The next time `bt_mesh_rpl_check`
is called, it may stop iterating `replay_list` earlier than it should
because it will meet an empty entry before it iterates over all entries
in the list.
This commit does defragmentatino of `replay_list` on every
`bt_mesh_rpl_reset` by shiting existing entries to the vacated places.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Update the users of the "write" callback in the
bt_gatt_subscribe_params to use the new "subscribe" callback instead.
Signed-off-by: Asbjørn Sæbø <asbjorn.sabo@nordicsemi.no>
Previous check in the if-statement would never allow to send last
segment if msg->len + 2 == MTU * x.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
In order to bring consistency in-tree, migrate all subsystems code to
the new prefix <zephyr/...>. Note that the conversion has been scripted,
refer to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When receiving Transaction Start PDU, assure that number of segments
needed to send a Provisioning PDU with TotalLength size is equal to SegN
value provided in the Transaction Start PDU.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Bluetooth Mesh uses tinycrypt library for security related
algorithms. This PR encapsulates tinycrypt dependency within
one file to make the current implementation more portable.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
There is potential buffer overflow in pb adv.
If Transaction Continuation PDU comes before
Transaction Start PDU the last segment number is set to 0xff.
The current implementation has a strictly limited buffer size.
It is possible to receive malformed frame with wrong segment
number. All segments with number 2 and above will be stored
in the memory behind Rx buffer.
Signed-off-by: Aleksandr Khromykh <Aleksandr.Khromykh@nordicsemi.no>
There is errata clarification (Errata ID:18700)
about subscriptions on fixed group addresses.
It is possible to subscribe models on non primary elements
on any fixed group address except all nodes address.
Devices should be able to receive messages on fixed addresses
even if they do not support the feature
to which the fixed group address belongs.
Signed-off-by: Aleksandr Khromykh <Aleksandr.Khromykh@nordicsemi.no>
This updates the default proxy filter size to 16. Previous value of 3
is too less for the most practical uses and demos. The default proxy
filter type is accept list type and in this mode proxy server rejects
incoming messages from source addresses not in the accept list. The
addresses are added to the accept list when proxy client sends
messages to unicast addresses or manually adds certain addresses to
the accept list. Once this list is full more addresses cannot be added.
This also updates the default network message cache size to 32. The
network message cache helps in preventing duplicate messages getting
repeatedly relayed and helps in reducing unnecessary network traffic.
Previous value of 10 is quite less for most usecases and makes the
node appear to generate much more traffic in mixed network. The
updated value should suffice for most use cases.
Additional explannation is added in Kconfig to help users understand
the significance of this setting.
These two changes result in 176 bytes of additional RAM usage in mesh
samples.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
Adds a Kconfig option for setting the Config Client and Health Client
timeout. Updates updates the default for Config Client to allow
reception of full sized message from a similar peer device at zero hops.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
Use shell_print_ctx macro when printing to shall from callbacks.
ctx_shell may not be initialized when callback is called.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Changes parsing of input string args to provide error checking.
This is to prevent unintentional command execution on garbage input
strings.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Fixes errornous arg index for new identity in cmd_node_id.
Fixes errornous arg index for uuid in mod_pub_set.
Fixes errornous arg index for net_idx in hb_pub_set.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Fixes errornous arg index for new identity in cmd_node_id.
Fixes errornous arg index for uuid in mod_pub_set.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Since the default syswork thread priority = `-1`.
`adv_send` will call when controller report advertising
sending completed, due to this process by BT RX task, will
maybe process this before `buf_send`, since, sysworkq will be
used by other place and defer by any place.
Note: secure beacon will be 40ms, and friend and lpn will be 20ms.
This problem is very easy to reproduce, especially in native posix.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
When pb-gatt advertising enabled, after extablish connect,
will call `cb->connected` and `cb->adv_send`.
In previous connected also clear `ADV_FLAG_PROXY` flag, but
in `adv_send` will attempt unref null point buffers.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
With BT_SETTINGS disabled, or when using an indefinite
RPL_STORE_TIMEOUT and not storing the RPL, the device will not be able
to follow the replay protection required by the spec. This adds a
warning about this.
Signed-off-by: Ludvig Samuelsen Jordet <ludvig.jordet@nordicsemi.no>
Changes ERR to WARN message when relay buffers
run out, as this is not really an error but a
consequence of high traffic.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
Don't replace destination of segmented message when acknowledgement is
received from a friend node, otherwise, when segments are retransmitted,
the destination will be used and the friend node will treat it as a new
segmented message.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Heartbeat publication sent callback can be used
as a watch mechanism to determine whether
the mesh stack is still capable of sending messages or not.
Signed-off-by: Aleksandr Khromykh <aleksandr.khromykh@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The extended advertiser would fail to build due to a missing kconfig
option dependency when relay was disabled.
Fixes#43172.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
When local node poweroff and power on again, will
receive iv update but within 96hours.
When 96h after, due to cache, we can't process this
beacon any more.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
According Mesh Profile 3.10.6 IV Index Recovery procedure
Upon receiving and successfully authenticating a Secure Network
beacon for a primary subnet whose IV Index is 1 or more higher
than the current known IV Index, the node shall set its current
IV Index and its current IV Update procedure state from the
values in this Secure Network beacon.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Since `CONFIG_BT_MESH_PB_GATT` represent to pb-gatt-srv.
We use `CONFIG_BT_MESH_PB_GATT_COMMON` to represent common.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
When Proxy advertising or PB-GATT Advertising Enabled and use a same
advertising sets.
As `adv_start` will call multi HCI Command will cause syswork_q yield.
At same time, if another thread(BT RX) all `schedule_send` will cause
unable send mesh message, because `ADV_FLAG_ACTIVE` was be set, but
`ADV_FLAG_PROXY` not set currentlly.
Add `ADV_FLAG_SCHEDULE_PENDING` indicate mesh buf has been pendings
but not scheduled, so when proxy advertising enable, let's take again,
as we can't break or terminated `adv_start`, so we must waiting proxy
advertising enabled.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
As use for simple message with no-segment send or receive.
This will be useful for ram-resource-constrained device.
such as bbc-microbit-v1.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Before this change, enabling CONFIG_BT_SETTINGS and calling
settings_load(), but delaying / not calling bt_enable would trigger an
assertion error due to a timeout. The fault is that the settings load
handler for the Bluetooth host assumes bt_enable has already been called
and sends HCI commands to the controller. This times out if HCI is not
running.
The fix is to skip loading Bluetooth settings before bt_enable. The doc
is updated to guide the user on how to enable Bluetooth after settings
have been loaded before.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
After PR: https://github.com/zephyrproject-rtos/zephyr/pull/38296
If we receive the second recovery after 192 hours after the first
recovery, we may still not be able to perform any recovery, even
if the IV Index differs by 42, because the `ivi_was_recovered` flag
will only be cleared during the iv update.
But still May lose iv update, as we did the first iv recovery.
This patch by checking the iv duration, if 192h later, auto clear
`ivi_was_recovered` flag.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
A common pattern here was to take the work item as the subfield of a
containing object. But the contained field is not a k_work, it's a
k_work_delayable.
Things were working only because the work field was first, so the
pointers had the same value. Do things right and fix things to
produce correct code if/when that field ever moves within delayable.
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Adds clause so that the LPN must have a established friend
connection for the connection terminate callback to trigger
upon clearing a friendship.
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
Adds state check to the friend_req_sent CB to ensure
that the CB does not alter the LPN state if it is in a
disabled state. This resolves behavioural issue for lpn_set(false).
Signed-off-by: Anders Storrø <anders.storro@nordicsemi.no>
