Add Clock Control driver support for Renesas RZ/G3S
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Rename the following properties in bindings and DTS:
-- freqs_mhz => freqs-mhz
-- cg_reg => cg-reg
-- pll_ctrl_reg => pll-ctrl-reg
Signed-off-by: James Roy <rruuaanng@outlook.com>
This driver is mostly the initial seed for further implementation of a
real clock driver.
It doesn't allow the user to choose the clock source for the various
peripherals. The driver hardcodes some sane values.
Note that for now, the driver snps,designware-i2c does not support
"clocks" attribute. So this patch hardcode the clock configuration in
the init of the clock driver.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
The Atmel SAM0 SoC enable peripherals clocks in distinct places: PM and
MCLK. The old devices had defined the peripheral clock enable bit at PM.
On the newer devices this was extracted on a dedicated memory section
called Master Clock (MCLK). This change excludes the dedicated bindings
in favor of a generic approach that cover all cases.
Now the clocks properties is complemented by the atmel,assigned-clocks
property. It gives the liberty to user to customize the clock source
from a generic clock or configure the direct connections.
All peripherals drivers were reworked with the newer solution.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Some platforms require special clock selection options. This could be
made using the already defined assigned-clocks from Linux clocks.
See 93ee800895/dtschema/schemas/clock/clock.yaml (L24)
This introduces the vendor atmel,assigned-clocks and
atmel,assigned-clock-names properties to generalize those conditions
in Zephyr for Atmel sam0 SoC series.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The real, applicable and trusted values are the ones flashed into BICR.
So, drop DT properties that replicate BICR and use runtime reads to BICR
instead.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The real, applicable and trusted values are the ones flashed into BICR.
So, drop DT properties that replicate BICR and use runtime reads to BICR
instead.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The nrf-hsfll was previously the only supported HSFLL clock, hence it
was not namespaced fully. Since we added nrf-hsfll-global, we should
add the namespace to nrf-hsfll as well.
Updates drivers and devicetree uses of HSFLL as well.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add specific device model for global hsfll clock and update dts tree
to use specific model. The clock is not fixed, and configurable at
runtime to predefined frequencies specified by the platform.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Support specifying divided clock buses by introduction of
STM32_CLOCK_DIV(div) macro. This macro can be used in devicetree to define
clock source of peripherals.
HSE is selected in devicetree using:
<&rcc STM32_SRC_HSE ...>;
HSE/2 can now be selected with:
<&rcc (STM32_SRC_HSE | STM32_CLOCK_DIV(2)) ...>;
This allows to use clock_control_get_rate() API in peripherals in order to
get desired clock rate.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Depending on the stm32 serie the MCO1/2 prescaler is a value
set in the CFGR register to divide the MCO output clock.
Use the same model based on the RefMan for other stm32 series
than stm32C0/F4/F7/H5/H7, once the MCO is in the DTS.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The Pico SDK defines a default value for its XOSC multiplier. Reflect
this in the device tree binding so that it doesn't need to be repeated.
Signed-off-by: Andrew Featherstone <andrew.featherstone@gmail.com>
This commit adds the clock driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
Remove the renesas,ra-clock-generation-circuit driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add npcm miscellaneous device control and power and clock control
instances.
Add device tree bindings for npcm power and clock control.
Signed-off-by: Alan Yang <tyang1@nuvoton.com>
The new update of clock device tree make the pll p q r clock
source cannot be choose by other node
This fix add 1 new dts binding for pll out p q r out line
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Introduce bindings for Series 2 oscillators: HFRCODPLL, HFRCOEM23,
LFRCO and LFXO.
Add clock tree representation in devicetree `clocks` node.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Move the process of replacing numerical values with macros to
the header, and set the division ratio in a numeric without
using macros in the device tree.
Change `clk-div` defined in `renesas,ra-cgc-pclk.yaml` to `div`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
DeviceTree typically references the clock source using the `clocks`
property defined in `base.yaml`, so we'll change it to this.
Also delete the custom clock source definitions in
`renesas,ra-cgc-pclk-block.yaml`, `renesas,ra-cgc-pclk.yaml`, and
`renesas,ra-cgc-pll.yaml`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
- Create a new compatible: nordic,nrf53x-oscillators, as other series,
e.g. nRF54LX contain a similar but different IP (with PLL control,
etc.)
- Adjust DT: use recommended node name, remove redundant status okay.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This defines raspberrypi,pico-xosc along with a configurable startup
delay multiplier. On some boards, the XOSC takes longer to stabilize.
Signed-off-by: Xudong Zheng <7pkvm5aw@slicealias.com>
`-` is preferred over `_` in devicetree property names.
Since, change `clk_src`, `clk_div`, and `clk_out_div` to
`clk-src`, `clk-div`, and `clk-out-div`.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Devicetree binding for NXP mcxc oscillator is not available.
Add the binding to be able to configure the oscillator in devicetree.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add bindings for nrf-fll16m and nrf-lfclk and update in-tree nodes
and boards to use them in place of the fixed-clock binding.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The HFXO and LFXO oscillators have properties which need to be
specified in the devicetree. These properties are used by clock
controllers, which get these properties from the devicetree.
The BICR also contains these properties. For now, the properties
are duplicated in the bicr node in the devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Background of this modification is to make clock control
driver code provided by Renesas vendor to support for Renesas MCU
on Zephyr.
Signed-off-by: Quy Tran <quy.tran.pz@renesas.com>
This update is to support clock API for RA8
Move the clock initialize function into clock driver
Peripheral clock now has 2 more property in clock cell for enable
and disable clock to peripheral module
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
