Commit c79b1a38aa ("samples: display:
Convert driver and lvgl sample.yaml to use depends_on") started using
depends_on in the sample YAML for a lvgl application instead of
platform_allow.
This breaks build testing with twister and overflow checking enabled
on more resource constrained platforms. The test case's .config
ends up with:
CONFIG_LVGL_HOR_RES_MAX=320
CONFIG_LVGL_VER_RES_MAX=240
CONFIG_LVGL_VDB_SIZE=64
CONFIG_LVGL_BITS_PER_PIXEL=24
And lib/gui/lvgl/lvgl.c, where we allocate a buffer of size:
(CONFIG_LVGL_BITS_PER_PIXEL *
((CONFIG_LVGL_VDB_SIZE * CONFIG_LVGL_HOR_RES_MAX *
CONFIG_LVGL_VER_RES_MAX) / 100)
/ 8)
Require 147456 bytes to build the sample, ultimately overflowing RAM
if you run something along the lines of:
twister -T samples -p <constrained_platform> --overflow-as-errors
This is a reasonable test to be doing to make sure that sample RAM
requirements do not get too big for a subset of platforms that are of
interest, and it no longer works.
To fix it, add a min_ram line for this case so that we can still run
overflow tests on a large set of samples without fine-grained special
casing or creating an ever-growing list of platform excludes for this
test.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Move to CMake 3.20.0.
At the Toolchain WG it was decided to move to CMake 3.20.0.
The main reason for increasing CMake version is better toolchain
support.
Better toolchain support is added in the following CMake versions:
- armclang, CMake 3.15
- Intel oneAPI, CMake 3.20
- IAR, CMake 3.15 and 3.20
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Add Atmel sam0 sercom[uart] pinctrl bindings and implements pinctrl at
driver level. It changes all sam0 boards to use new feature and remove
pinmux driver dependency for sercom[uart]. The samples that require a
binding were update to keep consistency and avoid errors.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Similar to commit c6ff61220e, use a
harness config to limit execution of the adafruit_2_8_tft_touch_v2
sample variant to boards that have this shield attached.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the display driver and lvgl sample.yaml to select boards for
the adafruit_2_8_tft_touch_v2 shield configuration by depending on the
arduino_{gpio,i2c,spi} features instead of using an explicit
platform_allow list. This will enable twister to automatically select
new boards that add support for Arduino ports.
The reel_board and reel_board_v2 are excluded due to a conflict between
display drivers (onboard display vs. shield display).
The ubx_evkannab1_nrf52832 board is excluded due to a conflict between
the arduino_spi and arduino_i2c ports, which cannot be used
simultaneously.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we can use the adafruit_2_8_tft_touch_v2 shield with
mimxrt685_evk_cm33 and frdm_k64f boards, start building the display
driver and lvgl samples for these boards in CI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This should align with subsys/display which we do not have yet. Plan is
to move lib/gui into subsys/display.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
