Replace the custom float32_value_t LwM2M type with native double, to
facilitate LwM2M API and improve floating point precission.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit allows let build echo_server sample with
overlay-netusb.conf.
USB subsystem must be enabled by the application.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fixes: #38403
Adding NET_DRIVERS menuconfig so that network drivers are grouped
together in its own menu entry under drivers, similar to most other
drivers.
This further has the advantages that `CONFIG_NET_DRIVERS` can be used
for testing to determine if network drivers has been selected.
This changed revealed a dependency loop where both `select` (for SLIP)
and `depends` (for PPP) which both depends on NET_DRIVERS` where in use
in the dependency tree for Qemu networking, especially NET_SLIP_TAP.
This is handled by defaulting `NET_DRIVERS` to `y` when building for a
Qemu target.
`SLIP` had a dependency to `!QEMU_TARGET || NET_QEMU_SLIP`. This is
changed so that SLIP prompt depends on `!QEMU_TARGET` which provides
full user control in hardware but makes the symbol promptless on Qemu
targets.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Finetune coap_server sample parameters for better user experience.
Reduce the maximum retransmission count to release resources earilier in
case client is unreachable and no longer responds. Increase the maximum
number of pending retransmissions, along with the heap size (the buffers
for messages are allocated on a heap), to improve sample responsiveness,
in case multiple unreplied messages are pending retransmission.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case no reply is received for notification message, remove the
corresponsding observer since it's no longer reachable, freeing slot for
another one.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The retransmission handler only increased the retransmission count, w/o
sending the actual message again. Additionally, the next retransmission
time calculation was broken - it did not take into consideration the
time that has already passed since before retransmission, and re-applied
the entire timeout value.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When using the IEEE802154 radio interface in CONFIG_IEEE802154_RAW_MODE,
there is no way to handle ack frames because of the dummy implementation
of ieee802154_radio_handle_ack() in the ieee802154_radio header file.
Removed the dummy implementation from the header so you can/need to
implement it in the application.
samples: added implementation of ieee802154_radio_handle_ack() to
wpan_serial and wpanusb sample
Signed-off-by: Gerhard Jörges <joerges@metratec.com>
From 2.4 to 2.7 the net samples pair echo-server/client increase the
SRAM requirements. This adjusts example features to free necessary SRAM
to run example.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
These are getting build failures due to some kind of devicetree
console definition missing. These devices don't do networking, and
strictly don't even have a proper console device (logging is done via
a host mechanism). Probably fixable. Not worth the trouble. Filter.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Rework NCP interface configuration and NCP sample. Remove
CONFIG_OPENTHREAD_COPROCESSOR_SPINEL_ON_UART_DEV_NAME and
CONFIG_OPENTHREAD_COPROCESSOR_SPINEL_ON_UART_ACM Kconfig
options in favor of chosen node zephyr,ot-uart usage.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add app.overlay which contains cdc-acm-uart node.
Rework sample to get CDC ACM UART device from devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Move to CMake 3.20.0.
At the Toolchain WG it was decided to move to CMake 3.20.0.
The main reason for increasing CMake version is better toolchain
support.
Better toolchain support is added in the following CMake versions:
- armclang, CMake 3.15
- Intel oneAPI, CMake 3.20
- IAR, CMake 3.15 and 3.20
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Regular OpenThread upmerge to bring in a fix for a possible
infinite loop and support for DNS service subtypes.
Signed-off-by: Damian Krolik <damian.krolik@nordicsemi.no>
CONFIG_DEBUG_OPTIMIZATIONS should not be enabled by default in
prj.conf for tests or samples. Remove it from a few places that it
is.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure a timeout for send/recv operations so that the sample can
recover in case the connection stalls (for instance due to IP address
change on an interface).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The Google server that the sample connects to sends a larger certificate
since recently. As the overall size of the message conveying the
ceritificate is ~4700 bytes now, current mbedTLS configuration did not
allow to reassemble the message and thus caused failure during the
handshake.
Fix this by increasing MBEDTLS_SSL_MAX_CONTENT_LEN parameter (with some
extra space for any future changes).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The Let's Encrypt X3 certificate is no longer in use, replace it with an
up-to-date certificate.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When a WIFI driver is slow to get interface up the system not connect
to WIFI access point. This add some tries to let driver be proper
initialize to allow accept connection request.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The sockaddr address length was not initialized properly
when receiving packets.
Coverity-CID: 232698
Fixes#35159
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In Mbed TLS:
commit eccd88871767e2fba5f3a079cfdfcb77c376cf20
Author: Gilles Peskine <Gilles.Peskine@arm.com>
Date: Tue Mar 10 12:19:08 2020 +0100
Rename identifiers containing double-underscore
changes the name of a symbol we use. As part of upgrading to newer
versions of Mbed TLS, change the name of the symbol we use.
A better fix would be to not use this symbol at all, and perhaps define
our own symbol the same way this internal symbol is defined within the
library.
Signed-off-by: David Brown <david.brown@linaro.org>
Refactor and simplify the bluetooth buffer configurations to improve the
easy of configurations and eliminate invalid ones.
By moving configurations out of host and controller specific
configurations and into a common one it becomes easier to configure
the host and controller separately as the same configurations can be
used as would be for a combined build.
All HCI configurations are now given exluding the matching HCI header,
which eases the configuration as the application don't have to know the
different header sizes.
The BT_RX_BUF_LEN is split into ACL and Event, as well as the suprising
use of Command size.
BT_L2CAP_RX_MTU is removed as the stack does not support reassembling of
HCI ACL data to larger L2CAP PDUs. The application will have to set
ACL RX size and account for the L2CAP PDU header itself.
BT_EATT_RX_MTU was removed as it is only used for setting a different
default value for another option which leads to the stuck kconfig symbol
problem.
The configurations can be updated according to the table below:
** New configuration | ** Old configuration
All configurations
BT_BUF_ACL_RX_SIZE | BT_L2CAP_RX_MTU + 4
BT_BUF_ACL_RX_SIZE | BT_RX_BUF_LEN - 4
BT_BUF_EVT_RX_SIZE | BT_RX_BUF_LEN - 2
BT_BUF_CMD_TX_SIZE | BT_RX_BUF_LEN - 3
BT_BUF_CMD_TX_COUNT | BT_HCI_CMD_COUNT
BT_BUF_EVT_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_ACL_RX_COUNT
BT_BUF_EVT_DISCARDABLE_SIZE | BT_DISCARDABLE_BUF_SIZE - 2
BT_BUF_EVT_DISCARDABLE_COUNT | BT_DISCARDABLE_BUF_COUNT
Controller-build
BT_BUF_ACL_TX_SIZE | BT_CTLR_TX_BUFFERS_SIZE
BT_BUF_ACL_TX_COUNT | BT_CTLR_TX_BUFFER
HCI-bridge
BT_BUF_ACL_TX_SIZE | BT_HCI_ACL_DATA_SIZE
BT_BUF_ACL_TX_COUNT | 6
Fixed invalid configurations setting either BT_L2CAP_RX_MTU or
BT_CTLR_DATA_LENGTH_MAX larger than BT_RX_BUF_LEN could lead to buffer
overruns.
Fix advertising report max data length calculation.
This always used the BT_DISCARDABLE_BUF_SIZE macro but this feature
can be turned off and advertising reports will be allocated from the RX
buffer in that case. Also controller-build does not have this buffer
(in hci_raw.c). Also the wrong HCI header was used in the calculation,
HCI event header should have been used instead of HCI ACL header.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Coprocessor sample was lacked of test configuration which makes
buildkite/zephyr to fail. This commit fixes it by providing test
configuration for this sample.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
The device has sent RESET_POWER_UP message before the communication
with the host hadn't been established. It could be observed with
pyspinel which displayed `Framing error`.
This commit fixes the bug by initializing NCP after the host stated
is ready to communicate.
This commit reverts initialization the USB stack into function
otPlatUartEnable to be consistent with others OpenThread platforms.
OpenThread co-processor samples are not affected by #27071 as they use
USB for SPINEL communication with host and not for UART console.
Note:
When co-processor communicates by USB CDC ACM and it is hard reset
(what is happening in current Zephyr OpenThread platform)
the connection needs to be properly handled by the host.
For posix platform used together with RCP it was implemented in:
https://github.com/openthread/openthread/pull/6454
and for NCP:
https://github.com/openthread/wpantund/pull/492 .
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
This application shows how to use SO_TXTIME option, which can be
used to specify the time when the network packet should be sent
out by the network device driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This option was only able to collect statistics of transmitted
data. The same functionality is available if one sets the
CONFIG_NET_PKT_RXTIME_STATS and/or CONFIG_NET_PKT_TXTIME_STATS
options.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The conn_raw_input() in connection.c will clone the incoming
packet so that it is possible to receive socket data in
multiple packet sockets. This is all fine except that if the
socket is never calling recv(), then the cloned net_pkt is never
processed and we will have a memory leak.
What this all means in practice, is that we should call recv()
for every packet socket in order to flush the socket for any
incoming data even if the socket is just sending data.
Fixes#34462
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The sample uses generate_inc_file_for_target for some "webpages" that
get included. However, the directory that the generated files are
put into: ${ZEPHYR_BINARY_DIR}/include/generated/web_page isn't
created and thus the build fails.
Add a simple 'file(MAKE_DIRECTORY ..)' to create the dir.
Fixes#34345
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove board code and a few associated samples/tests that explicitly
call pinmux_pin_set() to set a given pin as GPIO. This is handled as
part of gpio_mcux_configure() so we don't need to do it again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace all existing deprecated API with the recommended alternative.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add an overlay-capture.conf file that can be used to allow network
packet capturing in this sample app.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
A simple application that allows you to use net-shell to
configure network packet capturing. The captured packets are
sent to external systems for processing. This can be used
for debugging network protocols.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
