The stm32 wwdg driver was currently tested only on disco_l475_iot1.
Additionally add nucleo_f091rc, such that one board with an CM0 core is
tested. And add nucleo_g431rb, that one board is included that has
newer register mapping and a 128 prescaler.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Some tools consider this as commented code because of the ifdef, so
remove that and fix a coding guideline violation.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch removes scenario which was testing deprecated
API behaviors. Needed as As flash_write_protection_set() was
deprecated and became no-operation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Now that we can use the adafruit_2_8_tft_touch_v2 shield with
mimxrt685_evk_cm33 and frdm_k64f boards, start building the display
driver and lvgl samples for these boards in CI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds a new sample application demonstrating basic
usage of FT800 display controller including touchscreen events.
Signed-off-by: Hubert Miś <hubert.mis@gmail.com>
This fixes the limitation of sending an extended CAN frame.
Because the default value of `CONFIG_SHELL_ARGC_MAX` is 12 the maximum
number of bytes for an extended CAN frame is 7.
Increasing it to 13 to allow all 8 bytes to be sent from the shell.
Tested on nucleo_f767zi.
Signed-off-by: Cezar Burlacu <cezar@embeddedp.ro>
Add supported peci response codes 0x80 (Out of resources timeout)
and 0x81 (Resources required to service the command are in low
power state).
Signed-off-by: Diwakar C <diwakar.c@intel.com>
Remove SPI_[0-8] and SPI_[0-8]_OP_MODES Kconfig symbols as no driver
uses them anymore. We also cleanup board and sample code to remove
use of these symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set integration_platforms on these samples to just native_posix. This
should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A different configuration is applied when running this test
using west or using twister.
Both will use the disco_l475_iot1 overlay, but the extra config
for clock bus tunning is applied only when using twister and
samples is failed when run with west.
Move this extra config from sample.yaml to board .conf file so
it is applied in both cases.
Fixes#32376
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update sample espi driver test to exercise some SAF functionality
based on the limited hardware available. Note the SAF test will
erase a section of the flash. SAF tests are enabled for the EVB only.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Nordic watchdog does support a callback, but it has a time limit that
is too tight for the way this sample uses it. Add infrastructure to
bypass using the callback in this sample.
Also add more diagnostics explaining the status of callback use in the
sample.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Similarly to what was done for watchdog test,
update watchdog sample to be compatible with stm32 window watchdog
and enable testing by twister.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add some changes to adc sample to enable valid verdict generation
using twister:
-Replace 'single_line' keyword with correct 'one_line'
-Remove parenthesis from the sample output to enable regex verdict
-Add timeout to save time in execution
Additionally, add support for disco_l475_iot1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Clean up logging menuconfig by grouping configuration into
sections like: mode, processing configuration, backends.
Additionlly, removed LOG_ENABLE_FANCY_OUTPUT_FORMATTING which is no
longer in use.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This sample shows how to use the ADC API. Depending on the support of
sequential reads in the driver, 1 or 2 channels are read and printed.
A devicetree overlay is necessary to specify the used ADC channel(s).
Signed-off-by: Martin Jäger <martin@libre.solar>
The flash shell can now build when there isn't a chosen
zephyr,flash-controller available, so we can simplify the filter to
apply this sample to more boards.
Two STM32 H7 board configurations are excluded because the flash driver
isn't supported yet on the M4 core.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove UP Squared support for the gpio sample that was merged after
the sample itself was removed.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW16 provides information on mechanisms to enter and exit 4-Byte
address modes, returning the device to reset state, and how to
manipulate the values in the first status register.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW15 provides information on entry and exit from QSPI modes. In
particular, it specifies whether and how the status register must be
updated for this feature.
Add a JESD216 devicetree property for the Quad Enable Requirements
value.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Modify led_pwm sample in order to make it usable in device testing:
- Remove parenthesis from the logs as they prevent use of regex
- Add a harness_config multiline regex in order to enable verdict
generation
- Update README
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Currently the following shields will thus be supported
waveshare_epaper_gdeh0154a07
waveshare_epaper_gdeh0213b1
waveshare_epaper_gdeh0213b72
waveshare_epaper_gdeh029a1
Signed-off-by: Kim Bøndergaard <kim@fam-boendergaard.dk>
Signed-off-by: Kim Bøndergaard <kibo@prevas.dk>
Convert the driver so that it creates its instance basing on DT.
Remove no longer needed Kconfig option CRYPTO_NRF_ECB_NAME.
Also update accordingly the crypto sample.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
CAN_MCP2515_MAX_FILTER is not needed anymore and was probably just a
misunderstanding. Aligned it with the other CAN drivers.
This also was the last difference in the mcp2515 specific config for the
can sample, so that can be deleted as well.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Reordering of the struct elements to match the Linux format.
The __packed() is not necessary anymore.
std_id and ext_id is merged to id in the frame and filter.
Additionally, the frames are ready for CAN-FD.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The previous API can't change the sampling-point and only allowed
bitrates that fit the time segments.
The new API allows for shifting the sampling-point and adjusts the
number of time quantum in a bit to all more possible bitrates.
The functions to calculate the timings are moved to the can_common file.
They can be used for all drivers.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
some tests configured with CONFIG_NEWLIB_LIBC=y,
it's better to add a filter filter: TOOLCHAIN_HAS_NEWLIB == 1
in those tests yaml file.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds a sample application for testing
the LiteX clock control driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Do not enable CONFIG_SERIAL explicitly in the flash_shell sample. Leave
it up to the board definition to enable a suitable shell backend if
CONFIG_SHELL is enabled.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Adjust the sanitycheck filter of the flash shell sample to also depend
on the board having a chosen zephyr,flash-controller devicetree node (as
this is what is referenced in flash_shell.c).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The sanity check on this sample gives timeout failure
on reel board because of bad filtering. Because the
sample does not adopt ztest framework, sanitycheck in
our daily test will report this as failure, which lowers
our passrate but this is not a sample with errors.
Signed-off-by: Shihao Shen <shihao.shen@intel.com>
The sample is currently to tied to nrf9160dk_nrf9160 board. Refact to
allow build with board and select between device power management on or
off. Move nrf9160dk_nrf9160.overlay to proper boards directory and add
nrf9160dk_nrf9160.conf to set the correct device. Device PM needs SYS
PM be implemented and is an specific configuration and for those boards
that have it implemented user can add overlay-pm.conf to enable the
feature.
Fixes#28094.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The WS2812 SPI driver needs the pixel data to be clocked out on time,
with no gaps between SPI frames. This makes the nordic,nrf-spi
compatible unsuitable for use, since the corresponding driver doesn't
use EasyDMA to clock out the tx buffers.
Force the arduino_spi node in the DT to SPIM mode by setting its
compatible to nordic,nrf-spim. On nRF52832, this driver is disabled by
default due to Product Anomaly Notice (PAN) 58.
We happen to not be affected by PAN 58 in this instance, because we
never read data over the SPIM, only write it. So it's safe to enable
the SPIM driver. This requires a board-specific Kconfig fragment for
nRF52-DK to enable CONFIG_SOC_NRF52832_ALLOW_SPIM_DESPITE_PAN_58.
Fixes: #29877
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Improve the way the nrf_qspi_nor driver configures the SCK frequency,
to properly support QSPI also on nRF53 Series SoCs that use a different
base clock frequency (96 MHz).
Add also a relevant configuration in the spi_flash sample so that it
can run on the nRF5340 DK.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample allows to test the led-pwm driver. The first "pwm-leds"
compatible device instance found in DT is used. For each LEDs attached
to this device (child nodes) the same test pattern (described below) is
executed. The LED API functions are used to control the LEDs.
Test pattern:
For each PWM LEDs (one after the other):
- turn on
- turn off
- increase the brightness gradually up to the maximum level
- blink (0.1 sec on, 0.1 sec off)
- blink (1 sec on, 1 sec off)
- turn off
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
In npcx7 series, all of them support the Intel Enhanced Serial
Peripheral Interface (eSPI) Revision 1.0. This specification provides a
path for migrating host sub-devices via LPC to a lower pin count, higher
bandwidth bus. In addition to Host communication via the peripheral
channel, it provides virtual wires support, out-of-band communication,
and device mastering option over the Chipset SPI flash.
Becisdes introducing eSPI device in npcx7, this CL also includes:
1. Add eSPI device tree declarations.
2. Add npcx7-espi-vws-map.dtsi to present the relationship between eSPI
Virtual-Wire signals, eSPI registers, and wake-up input sources.
3. Zephyr eSPI api implementation.
4, Add OOB (Out of Band tunneled SMBus) support.
5. Add configuration files for eSPI test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Remove obsolete include of the shell_uart.h file.
It is sufficient to include the shell.h file.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordisemi.no>
ESPI is supported in MEC15 chips but similar to PECI, I2C, eSPI bus
testing requires another device to act as eSPI host.
While this sample can be run in EVB the HW connection to a eSPI host
(Intel RVP) is not documented/supported.
Mark as not supported in that HW only in Modular card
(which setup is documented)
Also remove duplicate definition of the "depends_on: espi"
in the end of the sample.yaml file
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Two samples require interacting with keyboard and mouse, and that
means necessary to provide correct fixture before run of that samples
in sanitycheck system. To skip or run the sample according to the
provided fixture in map-file necessary to add fixture definitions
into sample.yaml files
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Add the supported features section to serpente.yaml and overlay files
to the corresponding tests and samples.
Signed-off-by: Alexander Falb <fal3xx@gmail.com>
Add support for running the JEDEC SPI NOR flash sample on the ARM
Cortex-M3 DesignStart FPGA reference implementation.
Special care is needed to avoid overwriting part of the FPGA
configuration bitstream, which is stored in the onboard QSPI flash.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add sample where a fictious lenghty operation is required before a more
elaborate handshake is perform with eSPI master.
This requires sending SLAVE_BOOT_DONE virtual wire explicitly.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This sample controls up to 12 LEDs connected to a LP503x driver.
First, for each LED information is retrieved using the led_get_info
syscall and printed in the log messages. Next, from an infinite loop, a
test pattern (described below) is applied to all the LEDs simultaneously
(using the led_write_channels syscall) and then to each LED one by one
(using the led_set_{brightness,color} syscalls).
Test pattern:
For each color in red green blue white yellow purple cyan orange:
- set the color
- turn on
- turn off
- set the brightness gradually to the maximum level
- turn off
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
The spi_flash_w25qxxdv driver has been superseded by the generic
spi_nor driver for over a year. The only non-refactoring change to
the W25Q driver in the last 18 months was done to support a backport
to 1.14.
All devices supported by spi_flash_w25qxxdv driver are expected to be
supported by the spi_nor driver, using the standard `jedec,spi-nor`
devicetree compatible. No in-tree devicetree files make use of this
driver.
Remove the confusion about which driver to select by removing the
unmaintained redundant driver.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit adds the LiteX I2S devices usage example with:
- i2s rx and tx initialization,
- i2s rx and tx configuration,
- i2s rx receiving,
- i2s tx sending.
An application is a simple sound loopback - it allows to connect
a music source and a receiver such as headseat and listen to it.
Signed-off-by: Pawel Sagan <psagan@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add support for running the JEDEC SPI NOR flash sample on the ARM
Cortex-M1 DesignStart FPGA reference implementation.
Special care is needed to avoid overwriting part of the FPGA
configuration bitstream, which is stored in the onboard QSPI flash.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use non-default frequency 25MHz and Quad mode to ensure
frequency configuration is taking effect.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
An off-by-one error calculating the number of parameter headers caused
a third table to not be displayed.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add DT entry for the embedded QSPI NOR flash (GD25Q16) in the Adafruit
nRF52840 feather. Also added support for the spi_flash sample, which has
been used to verify the device.
NOTE: Device seems to fail when using high clock frequencies (e.g.
maximum QSPI frequency). It may be due to PCB layout issues.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Value of ret has been overwritten by flash_write_protection_set
before it could be returned from do_write_unaligned, which could
lead to reporting success when error code should have been returned.
Fixes#27641, Coverity-CID: 212142
Fixes#27642, Coverity-CID: 212143
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add a tag at sample.yaml to exclude the platform mec15xxevb_assy6853
because of unsupported. Refer github issue #27576.
Signed-off-by: Ningx Zhao <ningx.zhao@intel.com>
A zero value in the NPH header indicates one parameter header.
Increase the upper bound to process the last provided table.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
GPIO CSn active level transitioned from default active-low to
devicetree defined since the last time this sample was verified,
requiring the flags parameter in devicetree to be updated.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The boards efr32_radio_brd4104a, efr32_radio_brd4250b and
efr32mg_sltb004a have an on-board nor flash. It is already present in
the device tree, only the driver needs to be enabled.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Removes 'flash' command function that displays the command's subset.
Command's subset will still be displayed in current code.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
On large memory areas printing 8 bytes/line is not enough.
Increased printing 16 bytes per line.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Adds unaligned and pattern write functionality.
The reason this was added is chips with large pages, e.g. 256 can't be
normaly writen via shell, thus the need to write a pattern with any
length to a memory area.
The unaligned write command allows writing a data frament in any place
in memory, the data backup, protection, erasing and writing is
automaticaly handled. This makes it easier to test all flash controller
functionality in one command, also write any persistent data to any
flash address.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The previous commits added the SAM0 DAC driver. Now document and
enable it, including enabling it in the DAC sample.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds native_posix hw counter model and the counter driver.
Functionality is needed by software which is tested
on native_posix and has dependency on counter.
Hardware model was developed similarly to HW timer model.
The counter driver wraps HW counter functions and exposes
basic functionalities: starting, stopping, setting and cancelling
single channel alarms.
Code was tested against: tests/drivers/counter/counter_basic_api.
Signed-off-by: Filip Zajdel <filip.zajdel@nordicsemi.no>
Ensure multiple OOB transactions can be perform back-to-back
Check OOB transaction response length matches is as expected.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a new configuration option, LORA_SX12XX, that is shared for all of
the LoRaMAC-node-based radio drivers. By default, the appropriate
driver for the LoRa radio in the device tree is included is included
in the build.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This option should be selected by default, as right now LORA=y selects
REQUIRES_FULL_LIBC.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Instead of whitelist, use a filter that checks if a required
"atmel,at45" compatible node is present.
Add a build-only test case to be used by CI and provide a harness
configuration so that execution of the sample can be also verified.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample still used the old name of the nrf9160dk_nrf9160 board,
both in documentation and sample.yaml. Because of the latter, this
sample was not picked up by sanitycheck, what resulted in compilation
errors in the spi_flash_at45 driver not caught by CI.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This provides a better error message when building with CMake and
forgetting ZEPHYR_BASE or not registering Zephyr in the CMake package
registry. See parent commit for more details (split from parent for
better readability).
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Due to counter driver implementation change
"driver/counter/counter_ll_stm32_rtc.c: Add 1 tick to alarm"
It is necessary to adapt sample test (sanitycheck)
to take into consideration 1 tick precision/tolerance.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Convert with a combo of scripts and by hand fixups:
git grep -l DT_FLASH_AREA_.*_ID | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_ID/FLASH_AREA_ID(\L\1)/'
git grep -l DT_FLASH_AREA_.*_OFFSET | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_OFFSET/FLASH_AREA_OFFSET(\L\1)/'
git grep -l DT_FLASH_AREA_.*_SIZE | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_SIZE/FLASH_AREA_SIZE(\L\1)/'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Update mbedTLS commit along with the following fixes:
* Fix naming inconsistencies in some cipher modes, to match core mbedTLS
configs
* Add Kconfig to enable CTR cipher mode
Fixes#22421
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit adds a sample application intended to present capabilities
of the flash driver for AT45 family chips and to serve as a reference
of how to make use of that driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The LoRa shell requires the alias 'lora0' for the default radio. Use
the same alias for the samples to make them portable across different
radios and devices.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
LoRa drivers no longer depend on CONFIG_COUNTER. Remove this
configuration option from the samples.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert all canbus related API/samples/tests/subsys
to the new timeout API with k_timeout_t.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Convert DT_RTC_0_NAME to DT_LABEL() references based on which driver is
enabled for the platforms the test is supported on (NRF & STM32).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Get rid of legacy timeout API and move to new timeout API for LoRa.
This involves changes to API, SX1276 driver and sample application.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
This commit renames the CAN sample directory name from `CAN` to `can`
to be consistent with others.
Noting that the CAN driver test directory is named `tests/drivers/can`,
we have no excuse for naming the CAN driver sample directory
`samples/drivers/CAN`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
Convert driver to use new DT_INST macros throughout. We update one
sample app to use a nodelabel reference. We also remove defines in
dts_fixup.h as they are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Extend sample code to demonstrate the eSPI API to read/write flash.
Remove trailing \n
Use LOG_ERR when applicable instead of LOG_WRN
Treat warnings as errors.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Move to the new devicetree API and stop using DT_WDT_0_NAME fixup
macros. All existing in-tree SoCs with fixup names are still supported
here via compatible. The watchdog0 alias is also still supported.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This board contains an on-board Winbond W25Q16.
The chip is connected to spi1 using PB3-PB5 and PB0 as CS.
Signed-off-by: Bjarne Steinsbo <bjarne@gmail.com>
Remove usage of Kconfig symbols I2C_X and rely on overlay
to enable i2c instances in samples for stm32 boards
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
