The pin macros were used in the pre-DT pinmux era to configure the
mapping between a pin and its configuration.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
There is a name clash when using G4 series LL TIM driver depending on
the inclusion order of the LL TIM and pinmux headers. If the LL headers
are included after pinmux is included, AF1 and AF2 definitions used by
pinmux clash with the AF1 and AF2 TIMx register names.
In order to solve this problem with minimum impact, the following has
been done:
1. Prefix the AFx and ANALOG definitions with STM32
2. In order to avoid changing all *-pinctrl.dtsi files, the STM32_PINMUX
macro contatenates STM32_ with the provided mode.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Create the pinmux phandle to the ADC driver node in the
devicetree. When the pinmux_pin_set function in
adc_it8xxx2_channel_setup can refer to the setting of
this phandle. It is more flexible to use.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This CL introduces the Power Switch Logic (PSL) pads which detect the
wake-up events and turn on/off core power supply (VCC1) for ultra-low
-power consumption in npcx device-tree file.
By adding PSL input-pad objects, psl_in1, psl_in2, and so on, into
'psl-in-pads' property and configuring their 'flag' properties, the
related driver will configure them via soc specific functions later.
For example, if PSL input 1 pad that is plan to detect a 'falling edge'
event, this property should be:
vsby-psl-in-list {
psl-in-pads = <&psl_in1>;
};
And the flag property in psl_in1 should change to
&psl_in1 {
flag = <NPCX_PSL_FALLING_EDGE>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
On stm32f1 series, in output mode, there is no way to enable
pull-up/down resistors.
Clean these settings from helper defines.
Additionally add helper define to shorten few lines.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Macro STM32_PINMUX and related definitions are not compatible with
stm32f1 series and then should not be provided in -common.h.
Move them to stm32-pinctrl.h
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the DT nodes and binding for the pinmux registers,
aka IOCON (I/O control), found on the LPC11U6x MCUs.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
To work efficiently, SPI_NSS pins require pull-up configuration.
Fix this for whole STM32 series.
Fixes#17998
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
STM32 pin configuration comments where offset by 4 bits.
Fix this issue and make pin configuration settings
easier to read.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
This is done thanks to <soc>-pinctrl.dtsi file matching
the <soc>.dtsi files
Populate stm32 f4 based boards dts files with references
to uart pinctrl nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pinmux yaml file and bindings before introduction
of pinmux node in stm32 soc device tree files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
