MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
interrupt controller, also places its relevant
peripheral sources allowing drivers to use the
DT macros instead of espressif headers.
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Microchip XEC two custom DT properies girqs and pcrs cell sizes
are defined as constants. There is no need to replicate these
is the chip DTSI since the value cannot be changes. Fix the syntax
of the cell size constant to match the naming convention used
thoughout DT.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Update Microchip XEC RTOS timer driver adding MEC172x support and
using more device tree properities in the driver. We must also update
the XEC counter driver to use the new GIRQ DT properties.
Add new properties to RTOS timer and RTC timer YAML. These two timers
are linked due to option using a high speed timer for kernel busy wait.
Add Kconfig logic for XEC RTOS timer to MEC172x SoC.
Enable the Microchip XEC RTOS timer in the MEC172x evaluation board.
Add device tree nodes for most peripeherals.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add basic counter driver based on Timer Counter (TC) module for Atmel
SAM family.
Remarks:
- The driver is not thread safe.
- The driver does not implement guard periods.
- The driver does not guarantee that short relative alarm will trigger
the interrupt immediately and not after the full cycle / counter
overflow.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This CL introduces a kernel device driver implemented by the internal
64/32-bit timers in Nuvoton NPCX series. Via these two kinds of timer,
the driver provides an standard "system clock driver" interface.
It includes:
- A system timer based on an ITIM64 (Internal 64-bit timer) instance,
clocked by APB2 which freq is CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
- Its prescaler is set to 1 and provide the kernel cycles reading
without handling overflow mechanism.
- A event timer based on an ITIM32 (Internal 32-bit timer) instance,
clocked by LCLK which frequency is 32KHz and still activated when ec
entered "idle/deep idle" power state for better power consumption.
- Its prescaler is set to 1 and provide timeout event mechansim.
- Compensate system timer which clock is gating for better power
consumption after ec left"idle/deep idle" power state.
This CL passed starve, timer_api, and timer_monotonic test suites.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The compatible for the ARMv8 timer should have been arm,armv8-timer and
not arm,arm-timer. The dts binding file name was correct, just the
compatible was wrong. Rename dts, binding, and associated code to use
arm,armv8-timer.
Fixes#31946
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit is about it8xxx2 platform device tree.
Add driver's binding files, and one device tree as sample.
Signed-off-by: Cheryl Su <cheryl.su@ite.com.tw>
This adds support for GRLIB GPTIMER general purpose timer used in
LEON3/4/5 systems.
One of the GPTIMER subtimers is used to generate periodic interrutps
for announcing ticks. Another subtimer is used as upcounter for the
cycle_get_32() service.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
The number of capture/compare registers available on a peripheral
should be exposed in devicetree.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Adds a new LPTIM binding for stm32 soc,
based on the timer binding. This will makes a specific filter
on dt_compat_enabled("stm32,lptim")
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree. Move the prescaler setting
from Kconfig to devicetree as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add clock references for ADC and TC devices. Update the bindings for
these devices to require clocks property and update the dtsi files to
have the clock info.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The `xlnx,ttcps` binding, despite having the file name of
`xlnx,ttcps.yaml`, had the compatible property of `cdns,ttc`.
While it is true that the Xilinx ZynqMP platform embeds the Cadence
Triple Timer Counter (TTC) IP core, its TTC differs from the original
Cadence core in that it implements 32-bit counters, instead of the
16-bit counters defined in the original; hence, the Xilinx variant is
not compatible with the original Cadence version and should be treated
as a different device.
This commit changes the `xlnx,ttcps.yaml` compatible property to
`xlnx,ttcps` for the above reasons.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
ARM cores may have a per-core architected timer, which provides per-cpu
timers, attached to a GIC to deliver its per-processor interrupts via
PPIs. This is the most common case supported by QEMU in the virt
platform.
This patch introduces support for this timer abstracting the way the
timer registers are actually accessed. This is needed because different
architectures (for example ARMv7-R vs ARMv8-A) use different registers
and even the same architecture (ARMv8-A) can actually use different
timers (ELx physical timers vs ELx virtual timers).
So we introduce the common driver here but the actual SoC / architecture
/ board must provide the three helpers (arm_arch_timer_set_compare(),
arm_arch_timer_toggle(), arm_arch_timer_count()) using an header file
imported through the arch/cpu.h header file.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The binding for st,stm32-timers specifies #address-cells and #size-cells
as required but no dts files that have st,stm32-timers specify these
properties. Remove them from the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a kernel timer driver for the MEC1501 32KHz RTOS timer.
This timer is a count down 32-bit counter clocked at a fixed
32768 Hz. It features one-shot, auto-reload, and halt count down
while the Cortex-M is halted by JTAG/SWD. This driver is based
on the new Intel local APIC driver. The driver was tuned for
accuracy at small sleep values. Added a work-around for RTOS
timer restart issue. RTOS timer driver requires board ticks per
second to be 32768 if tickless operation is configured.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Same deal as in commit eba81c6e54 ("yaml: Remove redundant document
separators"), for some newly added stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add LiteX timer driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a level 2 interrupt controller for the RV32M1 SoC. This uses the
INTMUX peripheral.
As a first customer, convert the timer driver over to using this,
adding nodes for the LPTMR peripherals. This lets users select the
timer instance they want to use, and what intmux channel they want to
route its interrupt to, using DT overlays.
Signed-off-by: Marti Bolivar <marti@foundries.io>
Signed-off-by: Mike Scott <mike@foundries.io>
The 'id' field was never used and tended to just have the compat of the
node. Lets remove it and removed some code in extract_dts_includes.py
related to it. Added a warning if 'id' is set in a yaml so we can
remove it going forward.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add 'generation: define' directive to 'compatible' property.
When existing for a type of device, move compatible property
description in device base structure (eg: i2c.yaml)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
