Move odr options from Kconfigs to Device Tree. Moreover add
in DT a power-mode option to select among 4 possible values
(PD, LP, HR, HF). The power mode cannot be currently set from
sensor APIs.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all DT
bindings (as i2c and spi) handled by lis2ds12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Implements a shim layer driver using st hal for
I3G4250D gyro, mounted for example on stm32f3_disco_E.
No support for triggers included yet.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
This adds basic support for the Silabs Si7210 hall effect magnetic
position and temperature sensor. It is able to get magnetic field and
temperature in the default scale of the sensor (depending on the
variant). It also supports going into sleep mode without measurements
through the device power management infrastructure.
It is most notably missing support for scale change, measurement
averaging and filtering, and alert pin configuration (threshold,
hysteris, tamper).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This adds support for the TI INA219 Zero-Drift, Bidirectional
Current/Power Monitor with I2C Interface
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Rename:
- grove,light to seeed,grove-light
- grove,temperature to seeed,grove-temperature
The "grove" brand applies to a family of products by Seeed (sic):
https://www.seeedstudio.com/category/Grove-c-1003.html
Therefore we should use the existing vendor seeed.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
It should be "maxim,max30101", because the vendor prefix for this
company is "maxim", not "max".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing dts binding for sensor, this was causing build errors with
CONFIG_PM set on bt510/bt6x0 boards.
Fixes#37675
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add optional support for the DRDY/INT pin. This avoids waiting a fixed
time for the temperature and humidity conversion to finish.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This driver supports the TI INA230 and INA231 Bidirectional Current
and Power Monitors. The devices work on the I2C interface and are
created from DT nodes with a compatible property matching "ti,ina23x".
The following datasheets were referenced while developing the driver:
https://www.ti.com/product/INA230https://www.ti.com/product/INA231
Twister passed:
twister -T tests/drivers/build_all/sensor/
Testing was performed on the stm32g071b_disco board with the following:
Load: ~170 ohms
Voltage: 5V
Measured Values:
Voltage: 5.1 V
Current: 0.032 A
Power: 0.157 W
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Add support for power management and the shutdown mode for bq274xx fuel
gauge sensor. This now allows boards that have any kind of low power
mode to turn on or off the sensor.
Tested on a Company's custom board with bq27421 sensor on it.
Signed-off-by: Luka Lopotar <luka.lopotar@greyp.com>
This commit adds a driver implementation for the LM75 I2C temperature
sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@leica-geosystems.com>
Add driver for sensirion consumer humidity sensor line.
Supports shtc1 and shtc3, but only shtc3 is tested.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add basic support for TI HDC20XX series (e.g. HDC2010, HDC2021, HDC2022,
HDC2080). It is able to get temperature and humidity in the default
14-bit resolution. Triggers, resolution selection, interrupt line, auto
measurement mode are currently not supported.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move lis2dw12 trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common binding file that will be included by all bindings
handled by lis2dw12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add multi-instance support and make use of the stmemsc i2c/spi
read/write routine that has been introduced to simplify the ST
sensor drivers code.
Moreover, move spi-full-duplex property from Kconfig inside Device
Tree, so that each LIS2MDL instance can be configured selectively
in accordance to how it is used in h/w.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Change the drivers's compatible from atmel,sam-tc to atmel,sam-tc-qdec.
The atmel,sam-tc should be reserved for the future counter driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
STM32 internal temperature sensor driver.
This sensor can be used to measure the temperature of the CPU
and its surroundings.
Signed-off-by: Eug Krashtan <eug.krashtan@gmail.com>
The MAX17262 is an ultra-low power fuel-gauge IC which implements the
Maxim ModelGauge m5 algorithm. The IC monitors a single-cell battery
pack and supports internal current sensing for up to 3.1A pulse
current. The IC provides best performance for batteries with 100mAhr
to 6Ahr capacity.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lsm6dso driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Currently the MAX17055 driver assumes that a battery matching the
default characteristics is used.
This change allows battery characteristics to be specified in device
tree and writes them to the MAX17055 on initialization.
Existing default values are maintained for backwards compatibility.
Initialization routine taken from MAX17055 Software Implementation
Guide, document UG6365.
Signed-off-by: Hayden Ball <hayden@playerdata.co.uk>
Support single mode operation by enabling it and
making the driver to use the interrupt to findout
when the data is ready for fetch. The sample fetch
will be blocked for a specified maximum time untill
the interrupt happens.
* Make operation mode configurable in DTS file
* Make offset cancellation configurable in DTS file
* Use single common .yaml file for both i2c and spi
* Store above configurations in dev->config_info
Signed-off-by: Masoud Shiroei <masoud.shiroei@assaabloy.com>
Adds support for the Texas Instruments FDC2X1X Capacitance-to-Digital
Converter for Proximity and Level Sensing Applications.
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert ism330dhcx accel and gyro odr attributes from Kconfigs to Device
Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Converts ism330dhcx accel and gyro range attributes from Kconfigs to
Device Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by ism330dhcx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
During the driver init, the function will set the sensor resolution
based on the driver's dts variable "resolution"
The driver's device tree has been updated to include the value
"resolution".
The default is set to the highest resolution of 0.0625C.
Moved mcp9808_reg_write from mcp9808_trigger.c to mcp9808.c
This allows resue of the same function in both the trigger and
resolution functions.
Function name changed to xxx_16bit to distinquish it from the 8
bit write function that will added.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
Create a common binding file that will be included by all bindings
handled by iis2iclx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Initial driver and sample application of
TDK Invensense ICM42605 6-axis motion sensor.
This driver provide DTS for nRF52 DK board DTS setting.
Providing features are below.
Sensor data streaming - Accel, gyro
Tap, Double tap triggering.
Set/Get FSR, ODR by set attr API
Support multi instance feature.
Signed-off-by: JuHyun Kim <jkim@invensense.com>
Move iis2dlpc trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
