Fix the flash size to 64KB for the stm32H7RS series.
Restore the get_size API function for that series.
This is a specificity of this stm32 mcu (RefMan RM0477).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Support OSPI flash driver on EK-RA8M1 and EK-RA8D1 with ospi_b
and S28HL512T flash.
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
The LPC55XXX SoC series requires the use of a HAL function to read
from uninitialized flash without triggering a hardfault. This
broadens an existing #ifdef clause so that it is triggered for all
chips in the series instead of only the LPC55S36.
Signed-off-by: Wilkins White <ww@novadynamics.com>
Parameter checking of flash read API expects checking for len == 0
before checking dest buffer validation.
Fixes#87021
Signed-off-by: David Leach <david.leach@nxp.com>
Add Set_WP function to set SPI flash WP line to low
Add Get_WP function to obtain status of the SPI flash WP line
Signed-off-by: Benson Huang <benson7633769@gmail.com>
Commit 0e41b07309 ("drivers : flash:
update way to get flash size") changed the way to get flash size from
the LL_FLASH_GetSize() HAL function to the current DT_REG_SIZE() macro.
However, they are not equivalent:
- With LL_FLASH_GetSize(), REAL_FLASH_SIZE_KB returned the *total* size
of the Flash memory, reading it from a ROM register of the CPU. For
example, it was 2048 (2MB) for a STM32H747xI.
- The current DT_REG_SIZE() applies to a flash *bank*, therefore it only
returns half of the total Flash size on dual bank devices.
This mismatch causes issues with the DISCONTINUOUS_BANKS logic below,
incorrectly matching partitions close to the end of the first bank as
appearing to span both and triggering the "range overlaps discontinuity"
check later.
Fix it by doubling the size when appropriate, in the same way it is
already done for the M4 core.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
The stm32H7RS serie has no DelayBlock Bypass control in its DCR1 register.
For other stm32 devices with DelayBlock bypass control, set the value
directly in the structure.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the support of the stm32h7rs serie to the
drivers/flash/flash_stm32_xspi driver.
The stm32h7rs has no delayblock
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add the clock domain configuration for the xspi nodes
Where the DTS defines main clock and peripheral clock sel
plus a XSPIM clock
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add new device tree property specifying the number of
dummy-cycles required when reading the JEDEC ID.
The Arduino Opta has an at25sf128a with JEDEC ID 1F 89 01.
The PR below adds support for this, but the id read is 01 1F 89.
Changing DummyCycles to 16 causes the correct value to be read.
https://github.com/zephyrproject-rtos/zephyr/pull/89539
Signed-off-by: Mark O'Donovan <shiftee@posteo.net>
On some series, use of Delay Block could be possible on OSPI device but
not on HSPI one (which uses this drivers).
As a quick fix check the presence of XSPI Delay Block by-pass
configuration bit instead of the Delay Block presence.
Note: This fix works because we don't have cases today where this driver
is used for OSPI and HSPI instances with mixed DLYB compatibility.
This may have to be reviewed one day and may require a more complex fix
with instantiable configuration, but this day may never come as well.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Due to source data pointer having no alignment constraint,
extra care needs to be taken when reading source data
as dword
Signed-off-by: Yonas Alizadeh <yonas.alizadeh@alfalaval.com>
Most SPI NOR flash devices support a "fast read" command which uses
dummy bits between the address and the start of the data transfer. In
many cases, the maximum SPI clock speed of the device is lower for the
regular read command due to the limited time between the address and
data phases, so using the fast read command will remove this restriction
and allow for faster transfers.
Add a device tree flag to indicate that fast reads should be used for
the device.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Some Micron (and possibly other) SPI NOR devices implement a flag status
register which provides more information on the success/failure of erase
and program operations. In addition to better error checking, some of
these devices actually don't function properly if the flag status
register is not read after a program operation (subsequent reads will
only return 0xFF bytes).
Add a device tree parameter to indicate that the flag status register is
supported. When specified, the flag status register will be used for
ready/error checks rather than the standard status register.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
This driver was providing SPI buffers for both TX and RX on the data
payload portion of read transfers, even though the TX buffer is not
meaningful in these cases. As well as being less efficient, this also
caused likely uninitialized data to be transferred to the device, which
is possibly problematic.
Update to not include the TX buffer for the read data payload SPI
transfer, so that the SPI driver can generate dummy TX data internally.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Add the 4Bytes program mode to the stm32_ospi driver
to enter 4-Byte Address Mode (SPI_NOR_CMD_4BA) when flash is supporting it.
This is given by the JESD216 SFDP table.
Based on the stm32 qspi driver.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The value read from unwritten areas of Renesas RAxxx SoCs data
flash is undefined. To prevent reading unwritten areas a
blank check command is performed first. If the area is blank, we
return dummy data so it behaves the same as other flash devices.
Signed-off-by: Jeremy Dick <jdick@pivotint.com>
In hal_stm32 commit "update stm32h7rs to cube version V1.2.0"
e5eba65b76
the constants FLASH_OPTKEY1/2 for the STM32H7RS have been renamed to
FLASH_OPT_KEY1/2. For backward compatibility, 2 defines have been added
to Legacy/stm32_hal_legacy.h, so that FLASH_OPTKEYx is an alias for
FLASH_OPT_KEYx.
However, in Zephyr's STM32 flash driver, the alias is defined the other
way around since 5dc537389a, which leads to
Twister build failures, for example
https://github.com/zephyrproject-rtos/zephyr/actions/runs/14927867714/job/41936931524#step:12:1335
To fix the build issue, we can simply remove that alias in Zephyr, since
it is no longer needed.
Signed-off-by: Titouan Christophe <titouan.christophe@mind.be>
Since https://github.com/zephyrproject-rtos/zephyr/pull/83114 was merged,
I get twister errors unrelated to my pull requests for the STM32H7S78-DK
(for example https://github.com/zephyrproject-rtos/zephyr/actions/runs/14900504138/job/41851537049#step:12:1369)
This is because the function LL_GetFlashSize() was removed from hal_stm32
on the STM32H7RS series in
e5eba65b76
I am unsure if the removal from hal_stm32 is intentional. If yes, then this
commit should be merged into Zephyr to fix compilation for that target.
Otherwise, hal_stm32 must be patched, Zephyr's west manifest updated, and
this commit can be discarded.
Signed-off-by: Titouan Christophe <titouan.christophe@mind.be>
Add the MSPI controller support for apollo5x.
Add the MSPI controller to mspi API test.
Updated west.yml for hal updates.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
1. Moved ambiq specific macro to mspi_ambiq header.
2. Always fill rx&tx dummy settings regardless of transfer direction.
3. Add the CONFIG_MSPI_* macro for optional features.
4. Fixed the ID read process and add k_sleep during busy_wait in
atxp032 driver.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Use the LL_GetFlashSize to retrieve the size of the flash, reading the
system flash OTP of the stm32h5 serie. This operation requires
Icache disable/re-enable to access the 0x08FF F80C memory area
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implement the get_size flash device API function for the various stm32
This is just CONFIG_FLASH_SIZE expressed in Bytes or the FLASH_SIZE
given by the LL driver
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Move the flash_stm32_write_protection and
flash_stm32_option_bytes_lock functions to a common
file for stm32 devices including stm32h7
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace the assert on the value of the prescaler by a standard check and
an error value return (similar to the STM32 XSPI PSRAM driver).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Since the Dual Mode feature doesn't actually work when selected,
and we also realize that we can't support key features of dual
mode, such as bank swap using hardware.
As a solution, we desire to remove this Dual mode feature.
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
New property of the st,stm32-xspi-nor compatible gives
the external NOR flash in bits.
The property of the st,stm32-xspi compatible gives
the external NOR flash base address
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove XIP dependency for enabling memory mapping for Q/O/XSPI NOR Flash.
It is not necessary and is preventing configuring an external Flash in
memmap mode if there is no internal Flash (like on STM32N6)
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The current shim driver for flash-nxp-s32-qspi returns invalid error
when handling write, erase operations with zero size.
This issue causes the failure of the tests/subsys/settings/fcb/.
Updated to ignore the flash operations with zero size instead of.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Commit 857e5793f1 fix
the flash_mcux_flexspi_nor.c driver to wait for the
FlexSPI to be idle before performing write/erase
operations. Add a similar check to these drivers that
also use the FlexSPI NOR block.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Add a simple non-XIP transaction before deactivating the QSPI after
a XIP transaction is performed. This prevents a CPU hang from occuring
when another XIP transaction is attempted after the QSPI is activated
again.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use cache API for disabling and enabling ICACHE. The driver handles waiting
for ongoing cache invalidation.
Signed-off-by: Henrik Lindblom <henrik.lindblom@vaisala.com>
Move MSPI NOR commands to rodata.
Replace array with empty padding (~1kB) with macro-based assignments.
Ref: NCSDK-32779
Signed-off-by: Tomasz Chyrowicz <tomasz.chyrowicz@nordicsemi.no>
Extend driver to support single lane and 1-4-4 IO modes.
Move flash chip quirks to a separate file.
Signed-off-by: Marcin Szymczyk <marcin.szymczyk@nordicsemi.no>
The flash size is the second part (size) of the first reg value, not the
first part (address) of a nonexistent second reg value.
Based-on-patch-by: Armin Brauns <armin.brauns@embedded-solutions.at>
Signed-off-by: Tim Pambor <tim.pambor@codewrights.de>
-The stm32wba6x has Dual Bank memory. Change the flash driver
to support this OPTion given by presence of the
DUAL_BANK bit (21) in the FLASH_OPTR register.
-Flash erase with 2 banks: Add the control of the BKER
bit of the FLASH_NSCR1 to select BANK1 or 2 of
the internal flash depending
on the page number >127 for BANK2
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The LL_GetFlashSize function has been removed for
this new HAL H7RS release. Retrieves the value now from
the devicetree using the DT_REG_SIZE macro.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Use generic name for structure in driver instead of specific chip name
for better compatibility.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
