Separating declarations of variables not referenced with #ifdef
when CONFIG_IIS328DQ_THRESHOLD is disabled.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The CONFIG_PINCTRL setting is removed from the board
_defconfig files. And "select PINCTRL" is added to
the appropriate driver files.
Signed-off-by: Bill Waters <bill.waters@infineon.com>
The buffered and internal options were not assigned in the channel_cfg,
so they would end up at a random state.
The cfg struct is now properly zero-initialized and both options can
be set using optional parameters -b and -i.
Fixes#75884
Signed-off-by: Martin Jäger <martin@libre.solar>
The driver enables the clock of a gpio-port if any of the
pins use the port. This is done by calling pm_device_runtime_get
when a pin is used and pm_device_runtime_put when the pin is not
used anymore.
These calls needs to be balanced. But if a single pin was configured
as GPIO_DISCONNECTED multiple times, every time pm_device_runtime_put
was called.
This caused the clock of the port to be stopped and therefore also
other pins on the same port stopped working.
This commit fixes this by keeping track of which pin on a port
has requested the clock and only call pm_device_runtime_get or
pm_device_runtime_put when the clock-request for the specific pin
changes.
Fixes#77698
Signed-off-by: Jeroen Broersen <jbroersen@interact.nl>
The I2C transfer API has been recently changed to always automatically
set a STOP on the last message, which was well documented but
implemented only by few drivers.
Unfortunately, while documented, this is a change in the current
behavior and it turns out that some applications depended on it for some
complex operations.
Add a flag to temporarily restore the old behavior, buying time to fix
the application code depending on this.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add bool value that stores the CC change information received in
the interrupt of TCPC alert line. In sink role when in disconnected
state, polling the CC lines causes the chip to be awaken from sleep
mode increasing the power usage. When partner is connected, or any
other CC lines change happens, the chip informs about it with alert.
It can be cached and used instead of asking the chip directly.
Signed-off-by: Michał Barnaś <barnas@google.com>
Add support for VBUS measuring part of the TCPCI compliant device.
This device should be used as a child-node for the more specific
TCPC driver and referenced by the vbus property in the usb-c
connector node.
Signed-off-by: Michał Barnaś <barnas@google.com>
Add generic functions that will be common to all TCPCI compliant
drivers like registers reading, writing and updating.
Signed-off-by: Michał Barnaś <barnas@google.com>
Only ADC_REF_INTERNAL reference option is allowed in
adc_mcux_adc16 driver, but the reference is not used
for driver configuration. Internal, external or VDD
can be used in reality depending on SoC type and
its configuration.
Remove the reference option check to allow any reference
option from Devicetree.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Cadence I3C target FIFO width has been increased to 4 bytes in i3c
hardware REV_ID 1.7. Writing 1 byte to 4 byte FIFOs can cause
unintentional padding for bytes written from TX threshold interrupt
handler. Fixed the target callback to handle tx width of i3c target
writes to FIFO, by using run time rev_id check.
Signed-off-by: Naveen Gangadharan <naveeng1001@meta.com>
Fixed uninitialized return value variable issue, which would cause
functions to wrongly return non-zero value despite a successful
execution.
Signed-off-by: Chew Zeh Yang <zeon.chew@ambiq.com>
The TLC5971_STRIP config enables if the "ti,tlc5971" node exists.
Also, removing the setting that explicitly enables in the
`tests/drivers/build_all/led_strip` test.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add shell commands to enable/disable, move, set velocity, configure
micro-step resolution, and display stepper motor status. Includes an
`info` command to output all relevant data with graceful handling of
unsupported features.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Add VGA and QVGA resolution support to enable
usage of gc2145 sensor by smaller ram capable devices.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Introduce GPIO-based driver for MIPI DBI class that allows MIPI DBI
type A and B displays to be used on general platforms.
Since each data pin GPIO can be selected individually, the bus pins are
set in a loop, which has a significant negative impact on performance.
When using 8-bit mode and all the data GPIO pins are on the same port,
a look-up table is generated to set the whole port at once as a
performance optimization. This creates a ROM overhead of about 1 kiB.
Tested 8-bit 8080 mode with ILI9486 display on nRF52840-DK board.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
Instead of always using the SPI MIPI DBI mode (type C), look up the
mipi-mode from the device tree and only set the mode to
MIPI_DBI_MODE_SPI_4WIRE as a fallback in case the property is not given.
Signed-off-by: Stefan Gloor <code@stefan-gloor.ch>
This commit removes the y-selection of the `CONFIG_PINCTRL` Kconfig option
in FE310-based boards defconfig files.
It also makes drivers used in FE310 y-select `CONFIG_PINCTRL` if pinmuxing
is needed.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
On some EDMA versions, some TCD registers (e.g: SADDR, DADDR,
SLAST, DLAST, etc...) are extended to 64 bits via adding a new
HIGH register holding the value of bits [63:32]. Since, for now,
the driver doesn't support 64-bit addresses, this scenario is
supported by sign-extending the 32-bit value written to SLAST/DLAST.
SADDR and DADDR are taken care of on HAL side.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Some EDMA versions may have the channel MUX register in the MP
region. To support this scenario, use the `EDMA_HAS_MP_MUX_FLAG`
flag to figure out which channel MUX register to use (TCD or MP).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Currently a user, or a shield definition, must select a Kconfig to
signal that the iovdd_ctrl and bucken GPIOs are connected to the same
pin. We can instead check this in the driver by simply checking if
the iovdd_ctrl_spec and bucken_spec are the same pin.
Update the nrfwifi driver and remove the redundant
NRF_WIFI_COMBINED_BUCKEN_IOVDD_GPIO config.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Register all the lpi2c instances.
Add no-power-level property and update driver
to adapt no-power-level property.
Signed-off-by: Lucien Zhao <lucien.zhao@nxp.com>
The mcr20a driver referencing `MCR20Overwrites.h` which is under
`hal/nxp/mcux`.
So, put `depends HAS_MCUX` for clarify the dependency.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
When building with native_sim, We need to specify
```
#define _POSIX_C_SOURCE 200809L
```
to make `gmtime_r` available.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Fixes the mailbox notification callback that was not
being called from the ISR when the other side sends
something.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
Sometime, the radio causes a bus error.
This happens because we cast a struct and access to a member
that doesn't exists in the original struct.
This updates the driver to use the right struct to make the cast safe.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Currently, if we try to write data from a memory mapped flash address
to the flash then we get a -EINVAL error.
This could break the settings subsystem when we use NVS backend.
In order to make it work, add a buffer and use it when we want to
write data that is located in flash address space.
This has been tested using sample/subsys/settings/
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Do not allocate TxFIFO in a way that could corrupt Endpoint Information
Controller data (stored at DFIFO Depth address) or access locations
outside the SPRAM.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add timer device name autocompletion to the commands.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
These callback functions are not used outside of the file, make
them `static`
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
This reverts commit 311ddf90e2. That
commit breaks firmware boot on both MTL and LNL.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
For code clarity, this commit adjusts the use of `return` statements
in functions with a void return type as follows:
- Transform `return foo();` into separate statements:
`foo();`
`return;`
- Remove unnecessary `return` statements when
they don't affect control flow.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
By keeping track of run-time ATT MTU of all connected peers, it's
possible to increase the notification payload size; thus increasing
data-throughput sent over Bluetooth.
Note that this assumes the Bluetooth connection is properly configured
(with the corresponding connection parameters) to optimize performance.
This is application-specific and shall be examined on each scenario for
optimal performance.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
