The logging macros use _Generic() atm and it started to complain
when we are trying to print pointer value of gsm_dlci and gsm_mux
structs. Cast the pointer value to (void *) to overcome this.
Fixes#35329
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Switch the interrupt controller address to lower case to avoid this
warning:
stm32f723e_disco.dts.pre.tmp:97.39-102.5: Warning (simple_bus_reg):
/soc/interrupt-controller@40013C00: simple-bus unit address format
error, expected "40013c00"
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
uarte_enable function was not supporting a case when async
api was enabled but instance did not use it. Added runtime
check for async instance presence.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Driver was failing when interrupt mode was enabled for given
instance but interrupt driven TX part was not used. In that
case uart was not disabled after sending a byte which resulted
in continuous interrupt triggering. Added check for
fifo_fill_lock which is set when uart_fifo_fill is used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
In order to document the error codes, introduce a new reference section
describing the C standard library options available in Zephyr, along
with the definitions of the error codes.
At the same time move (most of) the content from the existing user guide
to the new API reference section, removing the need for a separate user
guide for it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a very simple check that verifies that new error numbers are added
according to the errno.h file in newlib, in order to maintain
compatibility with it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds the missing `ARM_TRUSTZONE_M` config flag
from TrustZone-enabled cores on LPC55sxx board targets.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
The network layer previously decided to use the friend credentials if
there was an established friendship. During the friendship setup phase,
the friendship is not considered established until the LPN receives the
first friend poll. Before this happens, the LPN should send a friend
poll message, encrypted with the friendship credentials. This wrongly
gets encrypted with the master credentials.
Change the decision point to whether the LPN has selected a friend,
which happens after the friend offer, and before the friend poll. This
will remain set for the duration of the friendship.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
This adds BT_MESH_SETTINGS_VA_PENDING to GENERIC_PENDING_BITS
as it should be stored by CONFIG_BT_MESH_STORE_TIMEOUT.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
This bug was introduced in PR #31176, where setting's flags were
moved out from bt_mesh.flags to pending_flags.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
When loaded via EFI, we obviously don't have a multiboot info pointer
available (we might have an EFI system table, but zefi doesn't pass
that through yet). Don't try to parse the "whatever garbage was in
%rbp" as a multiboot table.
The configuration is a little clumsy, as strictly our EFI kconfig just
says we're "building for" EFI but not that we'll boot that way. And
tests like arch/x86/info are trying to set CONFIG_MULTIBOOT=n
unconditionally, when it really should be something they detect from
devicetree or wherever.
Fixes#33545
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Kernel objects that contain embedded synchronization structures like
spinlocks can't be palced in the (cached/incoherent) stack memory on
coherence platforms like intel_adsp.
The normal fix in a test case is just to make the offending data
static, but that's painful here because SYS_BITARRAY_DEFINE declares
two objects (i.e. you can't put a "static" in front of it as with
similar macros) and it happens to be used in this case to define local
variables with collliding names, so I'd have to go in and rename
everything.
And there's little value anyway. Bitarrays are nearly-pure data
structures and extremely unlikely to show up platform-dependent
behavior.
Fixes#35242
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Two testcases of semaphore failed in ADSP due to the timeout value
we got back from the child thread is invalid. We put the variable in
the bss instead of in a stack, trying to avoid this.
Fixes#34687
Signed-off-by: Enjia Mai <enjiax.mai@intel.com>
The default behavior of the +KSRAT= command has
changed to not reboot the HL7800.
Adjust the command so the reboot takes place properly.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Simplified handling of runtime filtering that lead to removal
of LOG_CHECK_CTX_LVL_FILTER macro. Fixing multiply coverity issues
like CID 236013.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This was already implemented for firmware update packages.
For other opaque resources it failed to determine the target resource
id, which is now stored in the block_context.
Signed-off-by: Jan Buenker <jan.buenker@grandcentrix.net>
If the tests/net/socket/getaddrinfo is run in a board that has
Ethernet controller, then it is possible that it will interfere
the test if the Ethernet cable is connected. As the test only
needs loopback support to run, disable the Ethernet as it is
not needed by the test.
Fixes#34923
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
NPCX series ROM code changes the chip basic setting by firmware binary
header for loading the firmware from flash to RAM. Add the following to
improve the ec firmware header setting:
- Move the ECST which generates the firmware binary header to NPCX
common folder. All the following NPCX series chips can use this.
- Add ecst setting option in Kconfig.
Signed-off-by: Yuval Peress <peress@chromium.org>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Fix regression in PPIs use for nRF52805 SoC, which has
fewer of them. And the regression was introduced in
commit e603b9d59e ("Bluetooth: controller: Adjust PPI
used for nRF51x and nRF52x").
Fixes#35204.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixes compatibility with the Arduino bootloader reset mechanism when
using `west flash` on Darwin hosts.
stty is used to set the serial port in the bossac runner to 1200 baud on
Arduino ATSAMD21 bootloaders. The `-F` argument to stty is a GNU
coreutils addition, and thus it is missing from Darwin's BSD stty, so
change the flag to `-f` when we're not running on Linux.
On Darwin, set DEFAULT_BOSSAC_PORT to None and ask the user to select
one from a list of IOCalloutDevices reported by ioreg, modelled on the
get_board_snr from the nrfjprog runner. This is because serial port TTYs
are generated by the device driver, and therefore there is no safe
default.
Tested with an Arduino Nano 33 IoT board.
Signed-off-by: George White <me@galexite.uk>
add semaphores to ensure all services started before client query.
otherwise client query services may fail.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Z_ITERABLE_SECTION_ROM symbols were empty, meaning
that those symbols were not taking place in the linker script.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
A few mistakes in recent changes to this test:
There was a "LOCK_NO" (i.e. no locking!) case being exercised in
test_inc_concurrency, where three threads would race against each
other incrementing and decrementing a single count without
synchronization. And... it failed on cAVS. Because there was no
synchronization. Just remove.
The LOCK_IRQ (irq_un/lock()) case of the same test was was casting
taking a pointer to an integer (that stored the irq_lock() result) and
casting the pointer value to an integer instead of dereferencing it.
Also the workq test had a work item on the stack, which is forbidden
when KERNEL_COHERENCE=y
Fixes#34152
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Should not use -1 as an input parameter for unsigned int. Use zero
instead of -1 as invaild interrupt number to fix coverity warning.
Fixes#35146
CID: 235994
Signed-off-by: Enjia Mai <enjiax.mai@intel.com>
Increase the default thread analyzer stack size. On ARM systems the
stack usage is higher with CONFIG_FPU enabled.
The default of 512 is not enough in this case and lead to stack
overflow.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This CL limits the compiler to consider the eSPI/LPC host wake-up
functions, such as npcx_host_disable_access_interrupt and
npcx_host_disable_access_interrupt, only if eSPI bus module is selected.
Otherwise, we will encounter compiler errors if the communication
between host and ec is via SPI, not eSPI/LPC bus.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit fixes the ADC driver flow. And add internal
reference voltage to ADC driver API. And correct the
data buffer that only need to store raw data.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
After i2c_reset, there is still no external pull-up I2C bus,
and finishing off the rest of loop causes the code to hang
indefinitely.
This patch fixes that if I2C bus is not available(No external
pull-up), dropping the transaction.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
1. Refine some testcases for testing some character output function.
2. Delete some negative testcases which will not invoke fatal error.
Fixes#33822Fixes#33803Fixes#33801Fixes#33800Fixes#33790
Signed-off-by: Ying ming <mingx.ying@intel.com>
When marking the reserved region at the end of virtual address
space, call virt_to_bitmap_offset() is not needed as we already
know the offset. So remove it.
Coverity-CID: 235930
Fixes#35160
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This commit adds a new test to verify the thread safety of the C
standard functions provided by newlib.
Only the memory management functions (malloc and free) are tested at
this time; this test will be further extended in the future, to verify
the thread safety and re-entrancy of all supported newlib functions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit removes the lock inside the newlib internal `_sbrk`
function, which is called by `malloc` when additional heap memory is
needed.
This lock is no longer required because any calls to the `malloc`
function are synchronised by the `__malloc_lock` and `__malloc_unlock`
functions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds a lock implementation for the newlib heap memory
management functions (`malloc` and `free`).
The `__malloc_lock` and `__malloc_unlock` functions are called by the
newlib `malloc` and `free` functions to synchronise access to the heap
region.
Without this lock, making use of the `malloc` and `free` functions from
multiple threads will result in the corruption of the heap region.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
-ENOSYS should be returned if the operation is not implemented. This
issue was causing some PM tests to fail, as -ENOSYS was expected.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
