New nrfx release brings change of Low frequency sources symbols
in nrf_clock hal to uppercase. This commit aligns all occurrences.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
One of these samples was filtering all POSIX arch
boards out by explictly listing them by name
(and for the nrf52_bsim by lack of UART).
Instead filter by the architecture.
There is no functional difference in tree with this change.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Some of these samples were filtering all POSIX arch
boards out by explictly listing them by name
(and for the nrf52_bsim by lack of usb_device).
Instead filter by the architecture.
There is no functional difference in tree with this change.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Add an overlay to avoid running the samples/modules/canopennode
on the external octo NOR flash of the stm32h573i disco kit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The err variable is only used if the GPIO is configured in,
so move it to the right scope to avoid a build warning.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Change the sensorhub sample using a single trigger (on XL) and
fetching all channels (not only XL) in the callback.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Change sample to set CONFIG_FULL_LIBCPP_REQUIRED and to filter on
CONFIG_FULL_LIBCPP_SUPPORTED. Since not all toolchains provide a
full libc++ this will restrict the sample only to those environments
that do.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Use BT_CONN_TX_USER_DATA_SIZE when defining pools of buffers that will go
through `bt_conn_send_cb()`.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
Enfore a minimum duration between edges on the IRQ pin to give the HCI
controller time to detect the state change. Without this delay and with
several packets queued on the `rx_queue`, the pin could be re-asserted
almost immediately after being cleared.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
It was previously assumed that the 'sys_mem_blocks' struct would maintain
information about contiguous blocks allocated so the release API only
took the starting address. This led to an issue where allocating 2+
blocks would end up with a memory leak because any block not being the
first would never be released.
Add the buffer length as an argument so the correct number of blocks can
be released. Also, ammend the tests to match and verify.
Signed-off-by: Yuval Peress <peress@google.com>
Some samples, tests got missed in the switch from void main() to
int main(). Cleanup those samples/tests to use int main().
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Implementing USB-C Source functionality can be difficult.
This sample application serves as an example of how
to create an application with Power Delivery Source
functionality.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
When the only C library available is the minimal one, this test cannot
work. Accept only platforms with full C library support to prevent build
failures.
Signed-off-by: Keith Packard <keithp@keithp.com>
This symbol detects whether there is any available full libc for a
particular target, allowing tests to filter on this condition.
Signed-off-by: Keith Packard <keithp@keithp.com>
With the minimal C library malloc implementation moving to libc/common, all
of the related Kconfig variables have also changed. Update uses within the
tree.
Signed-off-by: Keith Packard <keithp@keithp.com>
Make it possible to use CPOL/CPHA SPI clock modes with the SDHC driver.
Some cards require the clock to switch to low when not active.
Signed-off-by: Łukasz Hejnak (LeHack) <lehack-ghub@lehack.pl>
Add expected output for ARMv6 CPUs in the mpu_test README, as this differs
from that for other AArch32 CPUs due to differences in how ARMv6 handles
faults
Signed-off-by: Katherine Watson <katie@radicalsemiconductor.com>
configure the nucleo_wb55rg with a prescaler on the LPTIMer input
clock to increase the max sleep duration.
With 32 the input clock is 1024Hz and max reachable timeout is
64 seconds.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
As of today it is not possible to use SPI dt-spec macros in C++,
something known and documented. The main reason is because `cs` property
is initialized using a compound literal, something not supported in C++.
This PR takes another approach, that is to not make `cs` a pointer but a
struct member. This way, we can perform a regular initialization, at the
cost of using extra memory for unused delay/pin/flags if `cs` is not
used.
Fixes#56572
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Extend the sample to be built with native_posix
prevent issues like #57133 in the future. Also extends the qemu
build to build a "raw" configurationw without POSIX_API or
NET_SOCKETS_POSIX_NAMES.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Fixes the compiler error that occurs when attempting to build
the SNTP library with CONFIG_NET_SOCKETS_POSIX_NAMES=n, while
using native_posix.
Closes#57133
Co-authored-by: Chris Friedt <cfriedt@meta.com>
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Remove include of adc dt-bindings header since these are
already included in the root .dtsi file that adds an adc.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
The out_of_tree_driver sample defines syscall functions, and
thus requiring CONFIG_APPLICATION_DEFINED_SYSCALL to be enabled
even if no userspace is involved. This is due to the function
generation for the syscall stubs.
Fixes#56946
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
NTC thermistor changes updated the sample app output,
correcting harness string to match sample app.
Signed-off-by: Al Semjonovs <asemjonovs@google.com>
PR https://github.com/zephyrproject-rtos/zephyr/pull/55129 deleted the
"port-sel" property. Delete this property from remaining Microchip SoC
variants and boards.
Test: west build -b mec172xevb_assy6906 samples/drivers/espi/
Signed-off-by: Keith Short <keithshort@google.com>
`bt_conn_le_create` returns a signed value. Error message format string
expects an unsigned value.
This commit changes the expected value in the format string to a signed
one, to match what `bt_conn_le_create` returns.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The `main` function now returns `int` instead of `void` and therefore
must return a value.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
The `main` function now returns `int` instead of `void` and therefore
any return statements inside it must return a value.
Note that any return values other than 0 are currently reserved.
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
This is a follow-up to commit 9fa35bc9a0.
Align specification of the expected console output with the changes
done to the sample in the above commit.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Avoid hitting the assert
```
__ASSERT_NO_MSG(net_buf_simple_tailroom(buf) >= len);
```
when the provided buffer is longer than we can fit. Instead discard the
packet and log an error.
This handling is similar to packets are discarded in hci_uart
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
