"st,mem2mem" property is supposed to be limited to dma-v1.
Remove its use in dma-v2 components.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to simplify the handling of DMA_STM32_V1/V2 and DMAMUX_STM32
symbols, set them directly based on related compatible status.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2 versions of DMA hardware blocks could be found across stm32 series.
In order to simplify the handling of matching Kconfig symbols,
make this visible in dts files by creating "st,stm32-dma-v1" and
"st,stm32-dma-v2" and set them accordingly in dtsi files.
Duplicate and update related bindings to reflect that new state.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adding acrn configurations specific to the platform
on which acrn boots zephyr, Only the EHL specifc
configurations for now. Keeping the HW clock frequency to
1900Mhz for EHL and using the new APIc timer driver.
Signed-off-by: Aastha Grover <aastha.grover@intel.com>
LPRAM_BASE and LPRAM_SIZE are duplicates of LP_SRAM_BASE and
LP_SRAM_SIZE respectively. Remove them and use LP_SRAM_*
consistently everywhere.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
On cAVS 1.8, 2.0 and 2.5 LSPGISTS and LSPGCTL are located in a
different shim register range, they cannot be accessed, using the
usual SHIM_BASE offset.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
CONFIG_BOOTLOADER_MCUBOOT is never used in cAVS builds, remove
code, supposedly supporting it.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
shim.h on cAVS 2.5 contains register definitions, copy-pasted
from other architectures. Fix them to correct values.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Tigerlake H has less RAM and fewer cores. Both should be
supported, selectable at the board level. For now use the H
configuration as more readily available for testing.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
1. don't use "inline" in .c, let the compiler decide
2. remove superfluous parentheses
3. simplify a function by directly returning the result of a boolean
operation
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
A configuration with CONFIG_MP_NUM_CPUS > 1 and CONFIG_IPM_CAVS_IDC not
defined is valid if COMFIG_SMP is disabled.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Shim register location on cAVS 1.5 is different than on 1.8 and up,
fix it.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
The current unused memory calculation is broken because it doesn't
take into account the stack area, allocated at the top of HP SRAM.
Until this is fixed disable powering down unused RAM.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Some interrupts can be enabled by the ROM, e.g. the timer interrupt.
When then in Zephyr the interrupt controller is enabled, before
individual interrupts are configured, interrupts can arrive and lead
to the spurious interrupt handler being invoked. Fix thid by
disabling all child interrupts when configuring cAVS interrupt
controllers.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
1. SOF doesn't have to be built in .bin format
2. don't include soc.c and soc_mp.c twice in cmake
3. remove an unused mailbox.h header
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
On cAVS 1.5, 2.0 and 2.5 platforms the correct manifest address is
0xB0032000.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
rimage dropped its "-m" parameter and switched over to using "-c"
for a configuration file, including a target name.
Add support for extended manifest for all cAVS versions.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Modifies openthread shim layer to automatically join multicast
addresses as they are added to zephyr from openthread, unless the
address is interface-local or link-local. This allows incoming
openthread multicast group messages to avoid being filtered by
zephyr ipv6 recv.
Fixes#31085
Signed-off-by: Joel Frazier <frazieje@gmail.com>
Line break on #error directive is confusing github and ending up
breaking syntax highligthing in github UI which makes me nervous
during review.
Convert error message to a one liner.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Due to clock discrepancy, busy waiting for 15us was not covering for
half tick in certain cases. Busy wait runs from HF clock source.
Increased to 19us to cover it. Anyway, this case is hit very rarely,
only when there was aborted, not-cancelled compare value that was
about to expire. Because of that, increase shall not impact the
performance.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
For historical reasons, the maximum speed of the Atmel SAM USB
controller is done by comparing the maximum-speed property string from
the DT using strncmp at runtime.
Now that the DT_ENUM_IDX macro exists, we can use it to get the
maximum-speed property at build time and without string comparison.
Unsupported speed can also be reported at build time.
Note that the default speed in case the optional maximum-speed property
isn't present in the DT is changed from full-speed to high-speed to
match the property description. This is a no-op in practice as this
properties is defined at the soc level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
During coverage reports generation in C++ code gcov_coverage_dump()
function would get stuck in endless loop. Fix by checking list head
pointer with current list pointer.
Signed-off-by: Marko Poljanić <mpoljanic@gmail.com>
CAN_MCP2515_MAX_FILTER is not needed anymore and was probably just a
misunderstanding. Aligned it with the other CAN drivers.
This also was the last difference in the mcp2515 specific config for the
can sample, so that can be deleted as well.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The commit
531fe89e80 (sanitycheck: use multiprcoessing instead of threads)
introduce regression for ARC nsim_hs_smp platform.
The regression is that verification on nsim_hs_smp hangs. That
happens because now we don't call try_kill_process_by_pid()
in the 'with' scope of the 'subprocess.Popen' when we spawning
BinaryHandler thread. Previously it was called via `terminate`
method of `BinaryHandler` but it was changed in 531fe89e80.
So if we can't terminate the simulator in a normal way
(which is expected for 'mdb' which is used for nsim_hs_smp
simulation) we will hang forever - we will never return from
'with' scope of the 'subprocess.Popen' as we are waiting for
process termination but the try_kill_process_by_pid() is located
latter and we never reach it.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Don't show the option for MCUBoot bootloader support
when the image being built is MCUBoot itself.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Fixed misalignment of bitflag in ll_conn type causing unintentional
overwrite between unions. Common flag must be present in master/slave
uinons as well. Problem is only present when enabling feature
CONFIG_BT_CTLR_CONN_META, which is default disabled.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Reserve two link rx buffer for each supported Broadcast ISO
sync instance, for establishment and for sync lost node rx
generation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
For tx_power_max_get and tx_power_floor, only allow for
positive values of txpower if they are defined.
Signed-off-by: Aurora Sletnes Bjørlo <aurora.sletnes@nordicsemi.no>
Document on how memory is mapped in different configurations starting
from the MCUboot partitioning of the flash. The given examples are for
TFM use cases and dual-core samples.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates lpcxpresso55s69 board's documentation with mailbox and multicore
setups. Explain how _cpu1 and _ns targets are used.
Also fixes TFM related documentation.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Adds multicore support for lpcxpresso55s69 board.
Documentation to be updated in a later commit.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Merges cpu0 and cpu1 targets to a single image, named multicore.bin,
this image can be found in the build folder.
Documentation is to be updated in a later commit.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
