The utility may be used during development stage to get
ambiq platform specific timing parameters for mspi devices.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
This device driver supports ISSI is25w/lx032/64 series flash.
Only extended SPI mode(1s-1s-1s, 1s-8s-8s, 1s-1s-8s) is implemented.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Due to the lack of the overlays for lots of platforms, bring up the
platform_allow again before the sample ifdef are refined
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
The sample was not able to build because of a typo in
Kconfig when enabling CONFIG_CHARGER_DISCHARGE_CURRENT_NOTIFICATIONS
Signed-off-by: Matthias Alleman <matthias.alleman@basalte.be>
Add support OSPI for Renesas ek_ra8m1, ek_ra8d1 to run sample
spi_flash
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Add support OSPI for Renesas ek_ra8m1, ek_ra8d1 to run
sample jesd216
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Add a board-specif dts overlay file for the adc_dt sample on the
STM32F4-DISCO board to enable for ADC channel support.
Signed-off-by: Ajith Anandhan <ajithanandhan0406@gmail.com>
This change would also solve that according to the C11 standard,
section 6.5, paragraph 4, the usage of bitwise operators on
signed integers is implementation defined.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Variables that holds pointers to 'const struct device' typically end-up
with '_dev'. The tcpserversink video sample did not have it. Add it.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Convert the log module declarationto the new syntax introduced in
5e34681 proposing a more compact syntax.
This fixes the log level not being updated in the "capture" sample.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Make the video software generator a devicetree node, which allows enabling
several instances, and select it as chosen { zephyr,camera = &... }; node.
It can be enabled via a `video-sw-generator` snippet.
Signed-off-by: Josuah Demangeon <me@josuah.net>
By having an "auto-fallback" mechanism, the VIDEO_SW_GENERATOR did shadow
the fact that "platform:mimxrt1064_evk:SHIELD=dvp_fpc24_mt9m114" was
missing the full specification, and therefore was not matched at all:
the shield was not selected, but the CI still worked.
Signed-off-by: Josuah Demangeon <me@josuah.net>
During testing and code inspection, there were various anti-patterns
on this (and U-Blox driver) codebase(s), including obfuscation, and
lack of data validation. This made it increasingly difficult to
introduce further variants of u-blox GNSS modems.
With this patch, both the UBX modem and the M8 driver have been
refactored to ease the reliability and maintainability of these
codebases. Here are some highlights:
WRT UBX modem:
- Helper macros to easily create UBX frames, (including checksum
calculation), at compile time; thus, making it easier to extend UBX
commands.
- Logic validation by the inclusion of the modem_ubx testsuite, used to
refactor the code through TDD.
- Ability to receive unsolicited messages, in order to enable U-Blox
drivers to rely on modem_ubx to transceive all commands, and avoid
hopping between modem_ubx and modem_chat.
WRT M8 driver:
- Remove GNSS specific protocol header files. Instead, unify them under
modem/ubx/protocol.h. Background: After a survey and looking at ubxlib
SDK I conclude the UBX protocol is by definition a GNSS protocol (there
are non-GNSS u-blox modems, but they're not interfaced through UBX
protocol).
- Establish pattern to create and send/receive commands using new
foundations on modem ubx.
- Remove dependency of Modem chat, and instead use UBX unsolicited
messages to get Navigation and Satellites data.
- Switch from the auto-baudrate detection pattern to a pattern of
transitioning between an initial known baudrate to a desired baudrate,
in order to improve initialization time.
- Add dts property to configure default fix-rate.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
this sample needs add dts defines for each platform, so should not be
generally enabled.
fixes: #90714
This reverts commit 022962c90d.
Signed-off-by: Hake Huang <hake.huang@nxp.com>
Add board-specific overlay file for the adc_dt sample
on the STM32F0-DISCO board to enable ADC channel support.
Signed-off-by: Sudarsan N <sudarsansamy2002@gmail.com>
Because this is a common testing scenario, almost any counter instance
should be able to run. Some counter instances cannot run this sample
should be filtered by platform_exclude or filter keywords.
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Remove trailing spaces at the end of log string.
Move arguments on the next line for readability.
Align arguments to first line.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Provide an initial video buffer in the first call to video_dequeue().
It is used by the driver for choosing between the input or output queue.
Applied to capture, capture_to_lvgl and tcpserversink samples.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Modify the capture sample to only run the video shell when the user
enables it with -DCONFIG_VIDEO_SHELL=y, as an alternative way to trigger
captures.
Signed-off-by: Josuah Demangeon <me@josuah.net>
The format pitch (bytesperline) field is typically set by the bridge
drivers, i.e. DMA, ISP drivers who actually handle the memory as they
know exactly the memory layout constraints.
Application just set the pixel format and resolution and must always
read back this field to see what the driver actually sets (to allocate
buffers for example).
Also, drop format pitch setting in sensor drivers as this is not needed.
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
M2M devices like ISPs or PxP have two separate buffer queues, i.e.
incoming and outcoming queues. For each API, the driver needs to
distinguish on which queue it needs to take action.
Add video buffer type to support this kind of devices.
- get_caps(), set/get_format(), enqueue()/dequeue(): the buffer type
is embeded in the video_caps, video_format and video_buffer structs
- video_stream_start/stop() : buffer type needs is sent as a parameter
Signed-off-by: Phi Bang Nguyen <phibang.nguyen@nxp.com>
