This change will allow the VIRTIO-MMIO register definitions
to be shared.
Additionally, the register names from Ver1 were being used,
even though the implementation was based on the Ver2 specification.
Also, I addressed this issue.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The `end` variable should be calculated based on the device's register
size, not the address. Probably never caught before as user typically
provides a buffer of reasonable size...
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
While it would likely not directly cause issues with the current
implementation, the logic of turning off the sensor should be to
actually reset the flags, not to toggle them.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Updated the CONF_STATUS0_DEV_ROLE macro to ensure proper bitwise
operation by adding parentheses around the bitmask operation.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add error handling for the return value of gnss_nmea0183_snprintk
so as to avoir sending garbage to the modem.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Correct improper doc for return value, document the negative error
codes, and add more details re: what the function does.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
I3C callbacks are registered by upper layer. Driver layer must check if
a callback is not NULL before calling it
Signed-off-by: Nghia Phung <nghiap@amperecomputing.com>
When Hotjoin complete and dynamic address is assigned to target,
INTR_DYN_ADDR_ASSGN_STAT interrupt will be triggered, we can use sem_hj
to notify dw_i3c_target_ibi_raise_hj() about Hotjoin completion
Signed-off-by: Nghia Phung <nghiap@amperecomputing.com>
Some external flash modules have extra commands to support, for example,
reading/writing an OTP zone. Given that the commands are highly specific
and difficult to generalize, we add two ex ops that can be used to
transmit a custom command (in the form of a full QSPI_CommandTypeDef) and
then read or write a user-provided buffer.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
The utility may be used during development stage to get
ambiq platform specific timing parameters for mspi devices.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
This device driver supports ISSI is25w/lx032/64 series flash.
Only extended SPI mode(1s-1s-1s, 1s-8s-8s, 1s-1s-8s) is implemented.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
add missing break statement so that CLOCK_CONTROL_AMBIQ_TYPE_LFXTAL case
is handled correctly.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
we iterate over all the channels, and if more than one channel is
active at a time. interrupt on any one of active channel was
triggering callback for other active channel, because flags value
is 1 (enabled). this is commit handle this behaviour and only
trigger callback if bits other than status is set
Signed-off-by: Anuj Pathak <anuj@croxel.com>
Make the GNSS emul driver less capable w.r.t fix interval so that we can
exercise more error paths if e.g. user requests a fix interval of 100ms.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Add option in enum phy_link_speed to disable auto-negotiation.
This allows PHY drivers to support disabling auto-negotiation.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
This commit fixes infinite loop reported in
https://github.com/zephyrproject-rtos/zephyr/issues/91242, not deallocating
array with virtqueues and not deactivating the virtqueues in case of
failure
Signed-off-by: Jakub Michalski <jmichalski@antmicro.com>
Add support for setting RGMII RX and TX internal delays via DT properties:
`ti,rx-internal-delay` and `ti,tx-internal-delay`.
Signed-off-by: Venkatesh Odela <venkatesh.odela@amd.com>
is_area_readable is used for SOCS other than LPC55XXX chips, not just
chips other than LPC55S36. Change the condition which elides this code
to avoid a GCC 14.3 warning.
Signed-off-by: Keith Packard <keithp@keithp.com>
