The Configure Data Path command must be included when the read Local
Supported Codecs [v2] command is supported. The Configure Data Path
command is needed when vendor-specific ISO data paths are supported,
but not otherwise tied to ISO. The respective weak function is
therefore moved to ull.c.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Fix filter accept list and privacy feature Kconfig default
based on whether host has them enabled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove experimental label from Advertising Extensions and
Periodic Advertising features in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Kconfig to limit the Primary Advertising Interval and
Periodic Advertising Interval maximum supported values in
the Controller implementation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Change CONFIG_BT_RECV_IS_RX_THREAD into a
choice:CONFIG_BT_RECV_CONTEXT with the following options
(names can be discussed further of course):
CONFIG_BT_RECV_BLOCKING
CONFIG_BT_RECV_WORKQ_BT
CONFIG_BT_RECV_WORKQ_SYS
This way users would be able to choose what to run most of
the BLE stack on, they wouldn't be forced to a single model.
We would default to CONFIG_BT_RECV_BLOCKING so that we wouldn't
need to change the system workqueue stack size by default, instead
asking users to do so if they select the CONFIG_BT_RECV_WORKQ_SYS option
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Add implementation in Controller to set radio high voltage
to enable support for +3dBm Tx Power in nRF53 Series SoCs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This command is used to obtain 'Implementation eXtra Information for Test'
(IXIT) values that are required to proceed with BT qualification tests.
Signed-off-by: Tim Sørensen <tims@demant.com>
- Implemented ISO-AL TX interface functions for fragmentation of
unframed PDUs
- Implemented ISO-AL source construct and its creation for an input
data path
Signed-off-by: Nirosharn Amarasinghe <niag@demant.com>
This adds support for the following Direct Test mode
commands:
- HCI LE Receiver Test [v3]
- HCI LE Transmitter Test [v3]
- HCI LE Transmitter Test [v4]
Those commands set add a possibility to test an CTE
reception and transmission. The HCI LE Transmitter
Test [v4] commands allows also setting a transmit power.
Signed-off-by: Kamil Gawor <Kamil.Gawor@nordicsemi.no>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add implementation to limit Extended Scanned data to a
configurable maximum length when generating HCI reports.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Provides interface, data structures and demuxing capability for ISO RX
PDU allocation and transport from LLL to HCI.
Uses the RXFIFO composite for simplicity and reduced overhead.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Implement ISO Synchronized Receiver connection handle
representing the streams in the BIG Sync. Add implementation
to return these handles on Sync Established event, and to
release these on Sync Lost.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Implement ISO Broadcaster connection handle representing the
streams in the created BIG. Add implementation to return
these handles on BIG complete event, and to release these on
BIG terminate.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation to check Periodic Advertiser
Synchronization to already synchronized peer and same SID.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Adding a KConfig to allow for disabling of the passing of invalid SDUs
through the ISOAL HCI data path.
Defaults to keeping current behavior.
Signed-off-by: Erik Brockhoff <erbr@oticon.com>
Fix Extended Scan Duplicate Filtering to consider different
advertising mode and multiple advertising set id from same
advertiser Bluetooth device address.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
With the introduction of `EXPERIMENTAL` and `WARN_EXPERIMENTAL` in
Zephyr all subsys/bluetooth and drivers/bluetooth/hci settings having
`[EXPERIMENTAL]` in their prompt has has been updated to include
`select EXPERIMENTAL` so that developers can enable warnings when
experimental features are enabled.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The filtering of periodic advertisements by scanner may be not needed
in certain situations e.g. while use of periodic advertising by BT ISO.
To make the code smaller and avoid execution of not needed code the
functionality will be conditionally compilable. It may be enabled
or disabled by use of CONFIG_BT_CTLR_SYNC_PERIODIC_CTE_TYPE_FILTERING
Kconfig option.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Introduce Kconfig for Read ISO Link Quality command. Support for the
command is optional according to the specification.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Implement support for Periodic Advertiser List to be used
in LE Periodic Advertising Create Sync command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactoring related to filter accept list, resolving list,
and removed the redundant anon variable.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add implementation defined channel index in the auxiliary
pointer of the common extended payload format in the primary
channel PDUs and the same be used in the transmission of
auxiliary PDUs.
Fixes#35668.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Replace the old whitelist-related terms with the new filter accept list
one from the Bluetooth spec v5.3.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fix maximum radio packet size configuration to use 255 bytes
for Extended Scanning and Periodic Synchronization.
Add a Kconfig option so that application can reduce RAM
usage if a specific user scenario can live with smaller PDU
receptions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Keep the default AD Data length to Bluetooth Specification
defined minimum of 31 octets.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix corrupt AD data used after directed advertising by
storing a backup of the AD data before switching to directed
advertising. Restore back the AD data with switching to non-
directed advertising.
The fix also addresses AD data backup when switching between
Legacy and Extended Advertising.
Fixes#18850.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Because we use the extended kconfig, we have already
supported relative paths, and it is clearer to use
relative paths in the bluetooth submodules.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Implement the functions required to calculate the SubEvent 1
and SubEvent n mapped channel indices.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added Kconfig option to configure the maximum Broadcast and
Synchronized Receiver ISO PDU length.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add BT_CTLR_ISO_TX_BUFFER_SIZE depends on Broadcast ISO
and/or Connected ISO feature being enabled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor and simplify the bluetooth buffer configurations to improve the
easy of configurations and eliminate invalid ones.
By moving configurations out of host and controller specific
configurations and into a common one it becomes easier to configure
the host and controller separately as the same configurations can be
used as would be for a combined build.
All HCI configurations are now given exluding the matching HCI header,
which eases the configuration as the application don't have to know the
different header sizes.
The BT_RX_BUF_LEN is split into ACL and Event, as well as the suprising
use of Command size.
BT_L2CAP_RX_MTU is removed as the stack does not support reassembling of
HCI ACL data to larger L2CAP PDUs. The application will have to set
ACL RX size and account for the L2CAP PDU header itself.
BT_EATT_RX_MTU was removed as it is only used for setting a different
default value for another option which leads to the stuck kconfig symbol
problem.
The configurations can be updated according to the table below:
** New configuration | ** Old configuration
All configurations
BT_BUF_ACL_RX_SIZE | BT_L2CAP_RX_MTU + 4
BT_BUF_ACL_RX_SIZE | BT_RX_BUF_LEN - 4
BT_BUF_EVT_RX_SIZE | BT_RX_BUF_LEN - 2
BT_BUF_CMD_TX_SIZE | BT_RX_BUF_LEN - 3
BT_BUF_CMD_TX_COUNT | BT_HCI_CMD_COUNT
BT_BUF_EVT_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_ACL_RX_COUNT
BT_BUF_EVT_DISCARDABLE_SIZE | BT_DISCARDABLE_BUF_SIZE - 2
BT_BUF_EVT_DISCARDABLE_COUNT | BT_DISCARDABLE_BUF_COUNT
Controller-build
BT_BUF_ACL_TX_SIZE | BT_CTLR_TX_BUFFERS_SIZE
BT_BUF_ACL_TX_COUNT | BT_CTLR_TX_BUFFER
HCI-bridge
BT_BUF_ACL_TX_SIZE | BT_HCI_ACL_DATA_SIZE
BT_BUF_ACL_TX_COUNT | 6
Fixed invalid configurations setting either BT_L2CAP_RX_MTU or
BT_CTLR_DATA_LENGTH_MAX larger than BT_RX_BUF_LEN could lead to buffer
overruns.
Fix advertising report max data length calculation.
This always used the BT_DISCARDABLE_BUF_SIZE macro but this feature
can be turned off and advertising reports will be allocated from the RX
buffer in that case. Also controller-build does not have this buffer
(in hci_raw.c). Also the wrong HCI header was used in the calculation,
HCI event header should have been used instead of HCI ACL header.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Consolidate Kconfigs for ISO roles to make compilation guards more
concise. Just introduces aliases, does not change functionality.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Ignore connection indications from peers that are already
connected. This is to bring the behavior of the controller in
accordance with [5.2, Vol 6, Part B, 4.5 Connection state]:
"If an advertiser receives a connection request from an initiator it
is already connected to, it shall ignore that request."
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
Remove support for nRF5340 PDK in the BLE controller.
The controller will now support only the nRF5340 DK.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Coded PHY is only enabled by default if the application is using
BT_HCI_RAW.
Coded PHY is not needed in most applications.
By disabling Coded PHY, most applications will:
* Get smaller in terms of flash and ram usage
* Not get vurnerable to devices trying to switch to Coded and
thereby increasing power consumption.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
