various microchip bindings set 'girq-cells' and 'pcr-cells'
sections in the bindings. However the bindings where for the
client nodes and thus do not need to set these.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers on a bus use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
This peripheral combines a hardware-based USB CDC ACM serial interface
and a JTAG interface.
It is present in the ESP32-C3.
Signed-off-by: Martin Jäger <martin@libre.solar>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The driver supported getting register shift from Devicetree, from a
custom definition in SoC headers (fragile) or, it took a default value.
This change simplifies things by making reg-shift property required in
all instances.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit aligns UARTE shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Add a new boolean devicetree property `tx-rx-swap` to the
st,stm32-usart binding, used to control TX/RX swap during
device initialization.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit makes the transition from the pinmux driver to the pinctrl
driver. It also modifies UART, SPI and I2C drivers used in FE310-based
boards to use the new pinctrl API.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
An additional devicetree poperty `single-wire` is added
to uart and usart bindings of stm32. The driver checks this value
during initialization and enables the single wire mode when set.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This patch adds support for the new pinctrl API to the UARTE driver. The
old pin property based solution is still kept so that users have time to
transition to the new model.
Notes:
- Some build assertions cannot be performed since the driver does not
have direct access to pin settings anymore. As a result user will not
be notified if HWFC is enabled but RTS/CTS pins are not configured.
- Hardware flow control can be enabled regardless of pin configuration,
it is now up to the user to configure RTS/CTS pins in DT.
- Some RX enable checks that were performed using pin information has
been replaced with a DT property that informs if RX is enabled or not.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Now that STM32 drivers are using pinctrl API, set pintrl-0 and
pintrl-names properties as required in order to report malformed
nodes description soon at build stage and avoid cryptic
DT api build error messages.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
IT8XXX2 uses shared ns16550.c driver which does not provide a power
management callback(pm_action_cb), so create driver to handle
IT8XXX2 specific UART features.
note: pm_action_cb(old name: pm_control_fn)
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
In order to have Espressif SoCs working with
the same uart drivers, all low level functions
are now replaced to hal_espressif HAL calls.
This also changes pinmux, gpio and uart
init order to meet its dependencies.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add hidden Kconfig option to Kconfig.cdc and allow
to configure CDC ACM UART device from devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Microchip XEC has been using the standard NS16550 driver.
Using the standard NS16550 driver requires extra HW programming
for XEC UART in board level and did not support XEC GIRQ interrupt
programming. We add an XEC specific driver and remove UART specific
register programming from the board level and implement interrupt
support. Also, by implementing a SoC specific driver we can add
driver PM in the future.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
based on uart rom functions, also enable console driver
on top of this driver, which enables logging
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This is a follow-up to commit 3656ba5ae9.
Do not enforce pull-up resistors to be enabled on RXD and CTS pins
in nRF UART drivers, as in certain hardware designs this may be
undesirable or may even make certain hardware not working.
Instead, provide devicetree properties that allow enabling of those
resistors when it is actually needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
