All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add configuration for SPI connected ADXL345 accelarator sensor
as adi,adxl345-spi.yaml.
Rename original adi,adxl345.yaml that configured for I2C
rename to adi,adxl345-i2c.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Remove the support for enabling passthrough mode support for MPU9150
on the AK8975. We don't have a proper MPU9150 driver and the MPU9150
has been EOL. So its highly unlikely this code is being used.
Additonally we remove the device tree binding for the MPU9150 since
we don't have a proper driver for it.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds support for the ds18b20 1-wire temperature sensor.
The sampling resolution of the sensor can be set in DT.
In case only a single device is on the bus, the driver issues
skip_rom commands. However, in case DT defines several devices,
the driver will use match_rom commands and therefore it is necessary
to set the rom_id of the device via the sensor attribute interface before
being able to sample sensor values.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
According to the formulas found in the reference manuals of the SoC
families using the "st,stm32-temp-cal" version of the temperature sensor
(i.e. G0, G4, H7, L0, L1, L4, L5, U5, WB, WL), the temperature is
computed with the following formula:
T = ((TS_CAL2_TEMP - TS_CAL1_TEMP) / (TS_CAL2 - TS_CAL1))
* (TS_DATA - TS_CAL1) + TS_CAL1_TEMP
What is called ts-cal-offset in the stm32_temp driver is therefore the
same value as TS_CAL1_TEMP1. Use it directly instead of defining another
property.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The stm32_temp driver defines the ts-voltage-mv property to determine
the reference voltage of the ADC in the temperature computation. However
this information is already available in the device tree at the ADC
level (even with the same default value). Use it through the ADC API
instead of duplicating the information.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This new DTS Node is defining a ratio for Vbat internal
bridge of monitoring sensor connected
to a ADC internal channel. The voltage reference value
is given by the ADC of the stm32.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This patch adds DTS properties for using wake-up mode
and the autosleep function to the ADXL362 driver.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
This sensor is virtually identical to the lsm6dso. The only difference
is the accelerometer ranges are double those of the lsm6dso.
Use the same driver. The difference is detected by using "st,lsm6dso32"
as the first compatible entry, followed by "st,lsm6dso".
An bit flag in the existing accel_range config field is used to check if
the chip is the doubled range or not.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
Comparator will monitor signal though ADC channel, based on
user configuration, callback will be triggered.
This will enable comparator functionality for nuvoton MCU utilizing its
ADC threshold detection feature. Implementation is exported through
sensor trigger API. Use of CONFIG_ADC_CMP_NPCX is required.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
This is a follow-up to commit 1a01ca2adf.
Since support for pinctrl has been added to the qdec_nrfx driver,
the related binding can no longer require the `a-pin` and `b-pin`
properties to be defined.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add DT option to configure the data ready interrupt mode.
Latched is the default; pulsed can be enabled through
the drdy-pulsed DT, if desired.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add FDS (Filtered Data Type Selection) + High-Pass reference mode support
(FDS in CTRL6, HP_REF_MODE in CTRL7)
Values are configurable through DT per instance.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
the icm42670 from Invensense/TDK is a 6-axis accelerometer with
gyroscope and temperature sensing capabilities.
this initial driver does not support the devices 2K FIFO or many of the
other advanced features. Instead, only basic features are implemented.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
This update Atmel sam qdec sensor driver to use pinctrl driver and API.
It update board and sample with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add support for the new pinctrl API to the nRF QDEC driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Allow movement detection to be used on hardware
that only has one interrupt line connected.
Change hardware configuration to a bitmask.
Signed-off-by: Andrew Hedin <andrew.hedin@lairdconnect.com>
This commit implements the temperature sensor interface for
the Maxim MAX31875Low-Power I2C Temperature Sensor.
Signed-off-by: Pete Dietl <petedietl@gmail.com>
This PR adds the different handling of temperature sensor for the
STM32L5 soc. In this soc, there are some calibration settings which
need to be applied for temperature conversion.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
The dts binding general rules document states that the property
description should explain why the default value was selected
(e.g. "default is the value at power-on").
See comment in #41143
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move odr and range properties for both accelerometer and gyro
from Kconfigs to Device Tree.
Fixes#41117
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Fix the yaml dts multi-line property description in the following
(expected) way:
description: |
PUT_TEXT_HERE
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adding support for the TI TMP108 temperature sensor. This includes
over/under temp interrupt support as well as one shot, continuous
conversion and power down modes.
Signed-off-by: Jimmy Johnson <catch22@fastmail.net>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lps22hh driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move odr options from Kconfigs to Device Tree. Moreover add
in DT a power-mode option to select among 4 possible values
(PD, LP, HR, HF). The power mode cannot be currently set from
sensor APIs.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all DT
bindings (as i2c and spi) handled by lis2ds12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Implements a shim layer driver using st hal for
I3G4250D gyro, mounted for example on stm32f3_disco_E.
No support for triggers included yet.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
This adds basic support for the Silabs Si7210 hall effect magnetic
position and temperature sensor. It is able to get magnetic field and
temperature in the default scale of the sensor (depending on the
variant). It also supports going into sleep mode without measurements
through the device power management infrastructure.
It is most notably missing support for scale change, measurement
averaging and filtering, and alert pin configuration (threshold,
hysteris, tamper).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This adds support for the TI INA219 Zero-Drift, Bidirectional
Current/Power Monitor with I2C Interface
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
