The current atmel sam flash driver was develop based on the cortex-m7
version of smart arm microcontroller. The driver support write
protection and cache functions which is not supported by other cortex-m
variants. This fixes current driver implementation and devicetree
entries for all sam variants.
Notes:
* The cortex-m3 doesn't have support erase pages flash command and
because of that the driver still not not compatible. Keep it disabled
until a patch be send. The hwinfo driver is not affected by this
restriction.
* The sam4l variation requires a specific driver because uses another
flash controller (flashcalw). Added another compatible to
differentiate and keeped node disabled until a driver be available.
Fixes#48516
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds `four-byte-opcodes` property. When set, then used write and read
opcodes will be converted to 4-Byte opcode.
Doesn't convert erase opcodes yet.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds write opcode (`writeoc`) property. That allows to provide
custom write opcode in the DTS.
Doesn't support OPI mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This includes DTS bindings for the Texas Instruments CC13xx/CC26xx flash
controller driver and adds support for it in CC1352R and CC2652R SoCs
DTS files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add the DTS binding for OCTOSPI interface for the stm32 devices
from STMicroelectronics.
This corresponds to a NOR octo SPI flash.
In this config, there is only on NOR-flash device.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add boolean properties to the binding for the nRF RADIO peripheral
to indicate whether the following features are supported:
- IEEE 802.15.4 mode
- 2 Mbps BLE mode
- coded BLE PHY
- high TX power settings
Set these properties appropriately in devicetree radio nodes for all
nRF SoCs.
Add also such properties and set them in appropriate nodes for nRF
flash controllers to indicate whether they support partial erase.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QSPI NOR flash driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The spi-bus-width property provides information if the target system
has all SIO[0123] pins connected to NOR flash memory.
It must be equal to 4 to enable QSPI 4 IO operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Some flash memories connected to QUADSPI IP block on stm32[fh]7 devices
require proper reset pulse before configuration.
This patch adds two new properties - the 'reset-gpios' phandle,
which allows specifying GPIO pin for RESETn pulse and
'reset-gpios-duration', which provides the time (in ms) for reset
duration.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
There is currently no information available about the XIP
addresses for the nRF52840 and nRF5340.
Add this via a new 'reg' block in the relevant QSPI nodes, along with
names for the register blocks so they are easier to retrieve.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add some details to help new users learn how to manage the nodes
for compatibles corresponding to IP blocks on Nordic SoCs.
The focus is on IP blocks where the pinmux is configured in
devicetree. These typically have individual properties for each pin,
like a SCK pin on a SPI peripheral, which correspond directly to a
PSEL register value. These violate the usual devicetree convention of
using a 'foo-gpios <&gpioX ...>' phandle property and work in ways
that only make sense if you understand the underlying register map, so
it's worth explaining them a bit more carefully.
Skip these two bindings, which have no drivers: nordic,nrf-i2s.yaml,
nordic,nrf-pdm.yaml.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit is about it8xxx2 platform device tree.
Add driver's binding files, and one device tree as sample.
Signed-off-by: Cheryl Su <cheryl.su@ite.com.tw>
With addition of flash_get_parameters API call, it is needed to provide
support for the API to flash drivers.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The st,stm32l0-flash-controller did not have a binding, add one for it.
Also made a comment in stm32l0.dtsi that the driver doesn't currently
support this controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most JEDEC NOR flash devices uses not only typical SPI mode
(MISO,MOSI,SCK and CS), but also QSPI mode (IO0,IO1,IO2,IO3,SCK and CS).
QSPI mode uses more data lines and as a result provide higher
throughput. If this were not enough, Nordic chips provide
hardware acceleration for read/write/erase functions, what
gives significant performance boost.
It does a lot of things "behind the scene", i.e when user has written
some data to the flash and would like to read them back, it has to wait
until the flash is ready by reading WIP bit in Status Register.
This driver does it automatically.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
Merge all the information into 'description:' and remove 'title:'.
Gets rid of a deprecation warning.
See commit 2934ee2cda ("dts: bindings: Remove 'title:' and put all info.
into 'description:'").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The amount of lock regions differs between different sam0 MCUs.
saml10: 2
saml11: 4
samd2x: 16
saml2x: 16
samd5x: 32
ASF does not provide a definition for this, so create a new one
in dts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit eba81c6e54 ("yaml: Remove redundant document
separators"), for some newly added stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add flash support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
