This change in pattern is meant to address a misconfiguration issue
that can occur for sensors that support being on multiple busses
like I2C & SPI.
For example, you can have a configuration in which such a sensor is
on the I2C bus in the devicetree and the sensor is enabled. However
the application configuration enables CONFIG_SPI=y and CONFIG_I2C=n
and this will cause the sensor driver to be built by default, however
since we don't have the I2C bus enabled the driver will not compile
correctly.
Previously we had been adding to board Kconfig.defconfig something
like:
config I2C
default y if SENSOR
This pattern doesn't scale well and may differ from what an application
specific need/use is.
So instead move to a pattern in which we leave the default enablement
up to the devicetree "status" property for the sensor. We then have
the Kconfig move from 'depends on <BUS>' to 'select <BUS>' and in
the case of drivers that support multiple busses we have the Kconfig
be: 'select <BUS> if $(dt_compat_on_bus,$(<DT_COMPAT>),<BUS>) for
each bus type the sensor supports.
This removes the need to add Kconfig logic to each board and enables
the bus subsystem and bus controller driver if the sensor requires
it by default in the build system.
Fixes: #48518
Signed-off-by: Kumar Gala <galak@kernel.org>
Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to align with macros used to obtain a device reference (e.g.
DEVICE_DT_GET), align the PM macros to use "GET" instead of "REF". This
change should have low impact since no official release has gone out yet
with the "REF" macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem _depends_ on device, not vice-versa. Devices
only hold a reference to struct pm_device now, and initialize this
reference with the value provided in Z_DEVICE_DEFINE. This requirement
can be solved with a forward struct declaration, meaning there is no
need to include device PM headers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Port some drivers to the recently introduced macros to showcase its
usage and be able to do some initial testing (nRF52840).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The result of temperature and relative humidity ticks ranges from 0 to
65535 which is the range of a uint16_t variable. Intermediate tmp
variable type has also been adjusted.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This fixes/improves the rounding errors that are introduced
through the truncation of integer division.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Fix the formula used to compute RH/ticks formula according to the Table
9 of the datasheet.
This patch also fixes coverity issue 238360.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix the formula that computes T/ticks according to the details found on
Table 9 of the datasheet.
This patch fixes coverity issue 238343.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of passing target states, use actions for device PM control.
Actions represent better the meaning of the callback argument.
Furthermore, they are more future proof as they can be suitable for
other PM actions that have no direct mapping to a state. If we compare
with Linux, we could have a multi-stage suspend/resume. Such scenario
would not have a good mapping when using target states.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Return -ENOTSUP if the requested state is not supported
- Remove redundant "noop style" functions.
- Use switch everywhere to handle requested state (not necessary in all
drivers, but better take off with consistency in place after current
changes).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The verb tense for the suspended state was not consistent with other
states. The likely reason: state was being used as a command/action.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM control function will only be called if the requested
state is different from the current one. A significant amount of drivers
were checking for state changes, now unnecessary. This patch removes all
this redundant logic.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Since the state is no longer modified by the device PM callback, just
use the state value.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The callback is now invoked to set the device PM state in all cases, so
the usage of ctrl_command is redundant.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The device PM subsystem already holds the device state, so there is no
need to keep duplicates inside the device. The pm_device_state_get has
been refactored to just return the device state. Note that this is still
not safe, but the same applied to the previous implementation. This
problem will be addressed later.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
