Set an overlay to build tests/drivers/flash/common/
drivers.flash.common.disable_spi_nor when the SPI NOR exists
but test does not use it
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add rtc tag to the siwg917_rb4338a board to activate testing on the
board.
Also add an overlay for the board in order to run the test correctly.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Enabled CONFIG_ALARM and CONFIG_UPDATE to enable these tests on intel
platforms.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Radio Board 4342A is really similar to the 4338A. There are a few
difference on the pinmux, but most of the peripherals and the SoC are
the same.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
The reference manual and the schematics of the reference designs
numbers the pins from 0 to 57. So let's also apply this scheme to the
pinctrl.
Note while PIN are numbered between 0 and 64, the GPIOs are represented
with 4 block of 16 GPIOs. This is the way the GPIOs are documented in
the reference manual, so we don't change that (In addition,
gpio_port_pins_t is a uint32_t, so it won't be possible to represent 64
GPIOs in one gpio_port_pins_t anyway).
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
"UNLICENSED" is not a valid SPDX License Identifier. Remove it from the
list and just keep "Apache-2.0".
Fixes: #89413
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add CS GPIO to nrf54h20dk/nrf54h20/cpuapp which is connected to
PORT which is in the "fast domain". The fast domain needs to be
resumed from thread context given it requires IPC communication.
This thus ensures that GPIO can be used with and without
PM_DEVICE_RUNTIME enabled.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Implement pm_device_runtime support to spi_loopback test suite.
Specifically:
- call pm_device_runtime_get() on SPI bus before using SPI bus
- call pm_device_runtime_put() once SPI bus is no longer needed.
This is after transceive has been performed, or after calling
spi_release_dt() after a transceive has been performed.
This addition has no affect if PM_DEVICE_RUNTIME is not enabled
on a board/test case basis.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
Add a testcase for building the stm32 dcmi driver on all
currently supported platforms / shields.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Fix bug introduced in 46a262ffe6 where the
fie.index field was expected to be incremented by the driver, while it
is the responsibility of the caller to increment it.
Fixes#89663
Signed-off-by: Josuah Demangeon <me@josuah.net>
New test case enables low-power standby mode, but disables testing
the lpc_rtc_highres driver, since it is used to wake the device from
standby mode.
Signed-off-by: Derek Snell <derek.snell@nxp.com>
The Microchip CAP12xx series has a configurable sensitivity and
can drive an optional guard signal to reduce noise sensitivity.
Signed-off-by: Jeremy Dick <jdick@pivotint.com>
This change plays with situation in nRF54L devices where XOTUNE make
LF clock calibration process starts a bit longer. Now HF clock
is configured to be ready right before LF calibration test.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Add the MSPI controller support for apollo5x.
Add the MSPI controller to mspi API test.
Updated west.yml for hal updates.
Signed-off-by: Swift Tian <swift.tian@ambiq.com>
Adds the device tree, Kconfig, and documentation files.
The following features have been confirmed working on hardware:
* LED
* Button
* UART
Signed-off-by: Charles Dias <charlesdias.cd@outlook.com>
Add a special testcase to test any stm32 target
The expected flash size is given by the config FLASH_SIZE (in bytes)
and stm32 flash driver API function should return the same value
Do not run on the stm32wb55 nucleo as 216K are reserved among the 1MB
(only 808K declared but mcu has 1MB)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Since the test is hardcoded to prioritize testing a spi nor flash if
there is one, add a twister case for disabling that config in case if a
platform should also test some other flash which is present, such as
internal SOC flash. I.e, relevant platforms would be those which have
both internal and spi nor flash enabled in DT.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
deleting two test-cases from drv8424 test-suite since these test-cases
are now present in stepper-api since #88835
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Add memc driver for the MAX32 HyperBus peripheral, supporting HyperRAM
and Xccela PSRAM memory devices.
Signed-off-by: Pete Johanson <pete.johanson@analog.com>
The PAN B511 evaluation board is a development tool for the
nRF54L15 from Nordic Semiconductor. Updates are based on latest
changes for nrf54l15dk.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Add test which is using two independent UART devices. Validate behavior of
asynchronous API.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
