1. kenistis dspi does support rx and tx with different size,
so skip the tx_bigger test.
2. dspi dma need internal alignment and 8192 bytes are too
many for k64, so reduce to 1440 bytes
fixing: #77010
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
The native_sim has already been added to the test cases of
`drivers.ieee802154.build.external` is not being appropriately
processed because there is no corresponding overlay.
Create an overlay as an alias of native_posix.overlay.
Also, add the native_sim/native/64 platforms in the same way.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Use `test_adc` in io-channels to be consistent in whole
tests/drivers/build_all/sensor/adc.dtsi file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Fix warnings caught by running west build. Another fix will have to go
in to see why twister was missing these.
#78348
Signed-off-by: Yuval Peress <peress@google.com>
-add nucleo_u083rc and stm32u083c_dk boards for testbench purpose.
- add min_ram property to skip test on boards with little ram size.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
The test_target_position test used a stack allocated `poll_signal` which is
kept as a refrence inside the gpio driver. Since the time for polling the
signal was chosen pretty narrow, the function exited with the driver still
trying to signal the stack allocated value upon movement completion.
Fix by adding the structs to the test fixture and increase the timeout.
Resolves#78466.
Signed-off-by: Fabian Blatz <fabianblatz@gmail.com>
Allow IRQs to work on every hart regardless of the mapping
of the contexts.
Add a test to validate the hart-context mapping.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Verify NRF GPIO driver with NRFX interrupts disabled.
Verify that driver handles properly 'get' and 'set' api methods.
When calling interrupt enable driver should report
'function not implemented' error.
Signed-off-by: Bartosz Miller <bartosz.miller@nordicsemi.no>
Install the second instance to 0x8(uei), because MSI is installed
to 0x3(msi) when SMP is enabled.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
using arduino header to simplify test settings.
arduino_header D2 and D3 can be used by default.
alt: 118 platforms are enabled for this test.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
- add overlays and kconfigs files for nucleo_u083rc and
stm32u083c_dk boards.
- update testcase.yaml for CI
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
This allows to run the test 'chan_blen_transfer' and 'loop_transfer' on
the sim3u1xx_dk board.
The functionality tested in `chan_link_transfer` and `scatter_gather` is
not (yet) supported by the Si32 DMA driver, and those tests therefore
not enabled.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Fix flexspi xip configuration issue regarding code relocation
due to the order of kconfig defaults being sourced
The flexspi setup was not being relocated to an on chip location
Also remove rt1060 conf file in flash common test which changes the
code relocation location to RAM, just keep as ITCM for all M7 which
as of now all have ITCM from NXP with flexspi.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add support for flashing the Adafruit Feather nrf52840 Express
using UF2 over USB.
Also standardise on using the UF2 variant, so add a non UF2 variant
of the Sense board, so it can be flashed using the SWD headers.
Created flash dtsi files for both SWD and UF2. These are actually identical
for many other boards and should probably be moved to common in future.
Signed-off-by: Jacob Winther <jacob@9.nz>
Update both versions of adafruit feather nrf52840 to be variants rather
than separate boards. The aim is to provide a more consistent approach
and to remove some unnecessary Kconfig redundancy.
Signed-off-by: Jacob Winther <jacob@9.nz>
Define DMA channels for MAX32 boards and add a new test case so that
DMA-based SPI transfers are tested.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Add all the necessary files to add apds9253 Avago sensor driver.
Sensor available at https://docs.broadcom.com/doc/APDS-9253-001-DS
Signed-off-by: Margherita Milani <margherita.milani@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
- Update `MAX_IRQ_PER_AGGREGATOR` to 1024 to match with the
devicetree
- Update `2ND_LEVEL_INTERRUPT_BITS` to 11 bits to
be able to encode the L2 IRQs.
- Update `NUM_IRQS` to 1036 (L1 has 12, L2 has 1024)
Update the `MAX_IRQ_PER_AGGREGATOR` config in testcase
accordingly, so that it won't overflow the configured bits.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Signed-off-by: Yong Cong Sin <yongcong.sin@gmail.com>
Add test which validates behavior of the UART driver when there
are errors on the receiver line.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
This commit removes the `hifive1` board from the `platform_exclude` list
for the `drivers.gpio.1pin` pin.
The root cause for why this platform was disabled was fixed in the recent
Renode version upgrade in the CI image.
Fixes#69350.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The linear battery charger will charge the connected battery up
to a specific voltage. This is different depending on the chemistry
of the battery. Most LiPo Batteries have a nominal voltage of 4.2V,
which is why the default voltage of the bq25180 is 4.2V.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
Use the RTIO work queue to fake the i2c submit calls for drivers which
haven't yet implemented the API. Applications can change the size of
the work queue pool depending on how much traffic they have on the buses.
Signed-off-by: Yuval Peress <peress@google.com>
