add driver for Monolithic Power Systems MPM54304 with basic
functionality to enable/disable the buck regulators
Signed-off-by: Elias Speinle <e.speinle@vogl-electronic.com>
Adds support for the CP9314 switched capacitor converter. The
CP9314 is a multi-level DC/DC converter capable of operating in
2:1 and 3:1 modes.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
This add regulator driver for Smartbond DA1469X SOC.
Driver can control VDD, V14, V18, V18P, V30 rails,
full voltage range supported by SOC is covered.
For VDD, V14, V18, V18P DCDC can be configured.
Special VDD_CLAMP (always on) and VDD_SLEPP are added
to allow configuration of VDD in sleep modes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Do not enable subsystem/driver shell modules by default and stop abusing
CONFIG_SHELL_MINIMAL, which is internal to the shell subsystem, to decide
when to enable a driver shell.
The list of shell modules has grown considerably through the
years. Enabling CONFIG_SHELL for doing e.g. an interactive debug session
leads to a large number of shell modules also being enabled unless
explicitly disabled, which again leads to non-negligible increases in
RAM/ROM usage.
This commit attempts to establish a policy of subsystem/driver shell
modules being disabled by default, requiring the user/application to
explicitly enable only those needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add binding, include header, and driver for NXP VREF IP block.
NXP VREF is an internal voltage reference generator on some SOCs
that fits well with the regulator API in zephyr.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add basic support of 'regulator-gpio'. For now, it is support
only controling voltage and driver presents only six functions:
* enable and disable the regulator;
* set and get voltage;
* count and list of voltage(s).
Signed-off-by: Mykola Kvach <mykola_kvach@epam.com>
AXP192 is a small and simple power management IC featuring different
LDOs, DCDCs, AINs and also GPIOs. It also offers functionaltiy for
battery management.
This change includes the basic regulator driver functionaltiy for
LDO2-3 and DCDC1-3 as well as the mfd driver layer. Further drivers
for GPIO and ADC will follow.
Drivers have been developed and tested on M5StackCore2, an ESP32-based
board. Support for M5StackCore2 is still in progress.
Signed-off-by: Martin Kiepfer <mrmarteng@teleschirm.org>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In some cases, it may be desirable to not have thread-safe reference
counting. For example, when CONFIG_MULTITHREADING=n.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
While nPM1100 is to be operated in fixed configuration for some
applications, it has some degree of configuration via GPIOs. For
example, mode (auto/PWM) can be configured via MODE pin. VBUS current
can also be adjusted using ISET pin, even though there is no API yet to
limit the PMIC input current.
This patch adds a new regulator class driver for nPM1100 PMIC, so that
it can be used with the standard regulator API when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add FFF-based fake regulator driver. This driver can be used as a stub
or mock in testing.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The "pmic" driver was in reality a driver for NXP PCA9420 PMIC. There's
no "universal PMIC". While the driver may work for other NXP PMICs, it
is clearly not generic for other vendors PMIC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add shell for interacting with regulator devices, to enable
users to test power management settings quickly and verify that their
regulator is functioning as expected. Also allows users to interact with
regulator PMIC devices
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds a generic i2c regulator driver, and enables the NXP
PCA9420 PMIC IC using this driver. The regulator driver also exposes an
additional API in include/drivers/regulator/consumer.h, which allows
drivers to implement support for adjusting voltage levels and current
limits, if their device supports it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add regulator compatibility string to Kconfig.fixed file
and allow fixed regulator driver to be enabled when compatible
node is defined. However, remove this option from common Kconfig
as it is legitimate to enable/disable regulator support.
Change menuconfig REGULATOR_FIXED to config since this
menu nesting is not necessary.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This provides structure for the regulator device hierarchy and a
driver for GPIO-controlled regulators along with its binding.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
