Rename the NXP LPCXpresso55S16 board definition from
lpcxpresso55s16_ns (non-secure) to lpcxpresso55s16 and remove TF-M
configuration options.
While the LPC55S16 does have Arm TrustZone support, there is no TF-M
support available upstream yet.
Fixes#35100
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Converts the bmg160 sample application to check the sensor device at
build time instead of runtime. This fixes a Coverity issue for logically
dead code introduced in commit 5832e588e3.
Fixes#35118
Coverity-CID: 235919
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the adxl372 sample application to check the sensor device at
build time instead of runtime. This fixes a Coverity issue for logically
dead code introduced in commit 72795c3e6c.
Fixes#35119
Coverity-CID: 235932
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If we don't get a dev pointer from device_get_binding() we should
not dereference it. Just drop the name from the printk message
as in the future this is likely to use DEVICE_DT_GET().
Fixes#35112
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Looks like I forgot to finish a sentence. There's nothing really
special besides the top level requirement for an enabled node which is
mentioned at the top of the page. Add a reference to the bindings
index while we're here to make it clearer what such nodes contain.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add a real README, convert the device getter to DEVICE_DT_GET_ANY,
and enable assertions to make debugging easier on new users.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The MAX17262 is an ultra-low power fuel-gauge IC which implements the
Maxim ModelGauge m5 algorithm. The IC monitors a single-cell battery
pack and supports internal current sensing for up to 3.1A pulse
current. The IC provides best performance for batteries with 100mAhr
to 6Ahr capacity.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
Switch to using I2C0 as this I2C controller on the FRDM-K64F is actually
configured (pinmux) for use and is available on an arduino header if
someone would wire up an adxl372 to it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctrl-0 properties for configuration of UART, I2C, SPI, FTM,
DAC, ADC, ACMP, and PWT peripherals. These settings are based on what
is defined in the board/pinmux.c file.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
These changes turn out to have been incompatible with the way pinctrl
drivers are going to work, so we need to go back to what we had before
until we can agree on a better approach.
Squash of the following reverts:
Revert "boards: nrf: fix deprecated I2C properties"
This reverts commit 2a4ac9ac02.
Revert "samples: switch nrf overlays to sda-gpios, scl-gpios"
This reverts commit 01bb08e7d8.
Revert "boards: nrf: switch to sda-gpios, scl-gpios"
This reverts commit 17a66304c4.
Revert "i2c: nordic: switch to phandle arrays for pinmux"
This reverts commit 821c03a14a.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add simple application to demonstrate quadrature decoder sensor.
Tested on Atmel SMART SAM E70 Xplained board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This sample application periodically reads raw data from the FDC2X1X
sensor in polling mode or optionally with data ready trigger.
It is able to read the 12-Bit and 28-Bit, as well as the 2-Channel
and 4-Channel versions (FDC2112, FDC2114, FDC2212, FDC2214).
The 4-channel versions are chosen through devicetree properties.
The default is FDC2112.
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
Set integration_platforms on these samples to just frdm_k64f.
This should be sufficient to make sure these tests build.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I only see one sample with an overlay using the now legacy sda-pin and
scl-pin properties. Move it to the new style.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Adjust the documentation and devicetree overlays so the sample can be
built for any board with an Arduino I2C and SPI pinout, defaulting I2C
and SPI to y to make it easier to switch between the two without
requiring a pristine build.
The user has to choose an appropriate overlay or have a sensor built
in to the board.
Use the newly introduced DEVICE_DT_GET_ANY() in main.c to ask for a
bosch,bme280 without worrying over the details or exposing
DT_DRV_COMPAT-based functionality that is really meant for drivers.
Remove the no-longer-needed board specific overlay for nRF52840 DK;
this is covered by the generic Arduino overlays now.
Fix the datasheet link while we're here.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add a sample application to test MAX6675 cold-junction-compensated
K-thermocouple to digital converter.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Introduce a dts board overlay on the nucleo_l053r8 board as this
board was used for testing addition of resolution setting on the
mcp9808 sensor driver.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
Add sample code which demostrates the use of the offset
register offered in the TMP117.
Also add information about tmp117 in README.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Add a sample for demonstrating the usage of the NXP MCUX Analog
Comparator (ACMP) sensor driver. The sample currently only supports the
NXP TWR-KE18F development board.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
some tests configured with CONFIG_NEWLIB_LIBC=y,
it's better to add a filter filter: TOOLCHAIN_HAS_NEWLIB == 1
in those tests yaml file.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add sample application for sensor lsm6dso. This sample has been
tested on stm32l562e_dk board, where lsm6dso is connect to I2C bus.
Signed-off-by: Yestin Sun <sunyi0804@gmail.com>
Enables the magnetic vector magnitude function in the fxos8700 sensor
sample application to ensure it builds in CI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts fxos8700 power mode options (normal, low noise low power, high
resolution, low power) from Kconfigs to an optional device tree
property.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
