It becomes the new default when the secure_storage_its_partition
devicetree chosen property is defined as it is a preferred alternative.
See the help message of the
`CONFIG_SECURE_STORAGE_ITS_STORE_IMPLEMENTATION_ZMS` Kconfig option
for more information.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
There are currently four types of roaming, 11r roaming, 11v roaming, 11k
roaming and legacy roaming, The priority of the roaming mode is
11r-->11v-->11k-->legacy roaming. If the ap does not support 11r/11v/11k
roaming, we will use legacy roaming. legecy roaming needs to do
full channel scan, which is the same as the general scan connection
process, so the legacy roaming time will be longer.
Signed-off-by: Gaofeng Zhang <gaofeng.zhang@nxp.com>
This fixes an issue where wrong values were checked against block device
defaults. Kconfig values are used when no filesystem config values are
provided, and the buffers are sized according to the Kconfig values,
but the checks were only performed against filesystem config variables.
Signed-off-by: Djordje Nedic <nedic.djordje2@gmail.com>
Some ARC processor configurations have separate memory for code (ICCM)
and for data (DCCM). Such configurations are unsuitable for LLEXT,
except for some quite special cases. For now, disable LLEXT and its
tests for these devices completely.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
The default exponent is 0, will cause twt setup quick failed,
set exponent value derived from twt interval to fix it.
Signed-off-by: Rex Chen <rex.chen_1@nxp.com>
In the case of IPV6 not enabled, when NET_SOCKETS_PACKET is enabled,
the sizeof(struct sockarr) will change to 20, the value of
MCUMGR_TRANSPORT_NETBUF_MIN_USER_DATA_SIZE is 8, which is not able
to pass the compilation, so I change its default value to 20.
Fixes#82757
Signed-off-by: Hongquan Li <hongquan.prog@gmail.com>
Add WIFI_SAP_IFACE_NO_IR state to keep same as hostapd_iface_state,
which is updated as the hostap upmerge.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
For CMD 'wifi ap status', removing HAPD related definition to make it
more commonly used for non-supplicant case.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
Don't check 'HEAP_MEM_POOL_SIZE != 0', as HEAP_MEM_POOL_SIZE might be 0,
but HEAP_MEM_POOL_ADD_SIZE_xxx is defined, which means the actual heap
size is not zero. So check KERNEL_MEM_POOL instead.
Signed-off-by: Maochen Wang <maochen.wang@nxp.com>
The user data size of the RFCOMM tx pool is zero. There is not enough
space to put the tx_meta data. Use CONFIG_BT_CONN_TX_USER_DATA_SIZE to
set the data size for the RFCOMM tx pool.
Signed-off-by: Make Shi <make.shi@nxp.com>
Most users won't be interested in the per-channel rules but only in the
country code, so, add a verbose option to hiden per-channel rules which
are too verbose.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
In order to prepare for extending the options, convert to getopt long
for easier parsing of options.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
This commit includes cleanups to `kernel_service`:
- `shell_tdata_dump()`:
Adjust formatting to align with `.clang-format`.
- `shell_stack_dump()`:
Update to pass `sh` directly instead of `user_data` since
it is already assigned.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Switch from using direct `strtoul` calls to `shell_strtoul`.
This change leverages the extensive error handling provided
by `shell_strtoul`.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
As `strtoul`, `strtoll`, and `strtol` guarantee to set `endptr`,
the initial `NULL` can be omitted.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Simplify `uart_cb_handler` by directly using `dev` instead of `cfg->dev`,
as both hold the same value.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
In case the peer device has NO SDP record, the result is valid,
but the result->resp_buf is NULL, it would introduce a hardfault.
Therefore, also add a NULL pointer check for result->resp_buf.
Signed-off-by: Make Shi <make.shi@nxp.com>
Increase the maximum value of LOG_BUFFER_SIZE from 64 KB to 1 MB
to accommodate varying device requirements.
Signed-off-by: Jungo Lin <jungolin.tw@gmail.com>
IAD must be before the interfaces it associates and therefore there is
no need for the class to be in charge of updating the bFirstInterface.
Update IAD in common initialization code and remove the updates from
classes.
This fixes UAC2 instances where the IAD bFirstInterface is not 0, e.g.
when HID was used together with UAC2.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Currently, there are build warnings that are triggered when building
for BT central and legacy OOB pairing only:
CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY=y
CONFIG_BT_CENTRAL=y
There was a PR that handled this issue in the past https://github.com/zephyrproject-rtos/zephyr/pull/74400.
Unfortunately, this PR even though it fixed the warnings it also
broke the BT peripheral and legacy OOB pairing only build:
CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY=y
CONFIG_BT_PERIPHERAL=y
https://github.com/zephyrproject-rtos/zephyr/pull/82552 was merged in
order to fix the issue with the peripheral build configuration.
Unfortunately, this PR reintroduced the warnings for BT central and
legacy OOB pairing.
This commit brings changes to make sure that both the BT central and
peripheral builds with OOB legacy pairing are buildable and
warnings free.
Also in this commit, a new build test case is added for the BT central
and legacy OOB pairing along the existing BT peripheral test case
Signed-off-by: Sebastian Panceac <sebastian.panceac@ext.grandcentrix.net>
This removes the deprecated CONFIG_NET_PKT_BUF_DATA_POOL_SIZE.
User should either use CONFIG_NET_PKT_BUF_RX_DATA_POOL_SIZE or
CONFIG_NET_PKT_BUF_TX_DATA_POOL_SIZE depending of net packet type.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Use CONFIG_NET_TCP_INIT_RETRANSMISSION_TIMEOUT and
CONFIG_NET_TCP_RETRY_COUNT to control the total timeout at the TCP
level.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
RTT backend can only be called from thread context and immediate
logging might lead to interrupt context use. Previously this limitation
was implied in different way and commit (c88a9ef27) got reverted.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add a separate test for public key validity. This needs to be done
synchronously so that we can respond with an early failure message to the
peer device.
Fixes#80218
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
If a shell command does not have a sub command, then the 3rd parameter
to SHELL_SUBCMD_ADD() macro should be set to NULL so that the help
will only print information specific to that command and not all
wifi commands.
Fixes#82633
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
When calling wifi_ap_disable() API specific WiFi driver implementation was
checked whether 'ap_enable' was provided, instead of 'ap_disable'. Fix
that copy-paste error.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Re-ran `clang-format` for consistent styling, simplified
multi-line statements, and consolidated string concatenations
where applicable.
This is a non-functional change focused on code formatting.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Added shell_device_get_binding() that wraps device_get_binding() plus
device_get_by_dt_nodelabel() so that a shell can easily get a device by
its full name or label.
Signed-off-by: Yishai Jaffe <yishai1999@gmail.com>
The weak syscall symbols generated by gen_syscalls.py are currently
compiled in the LLEXT subsystem library, which is then linked among all
other Zephyr libraries in an unspecified order. This can cause the weak
symbols to override the actual syscall implementations, leading to
undefined behaviour.
To fix this, the currently generated file is split in two elements:
- syscall_exports_llext.c contains the EXPORT_SYMBOL directives for all
syscalls. This part can be compiled with the LLEXT library and linked
among all other Zephyr libraries, and ensures all syscalls symbols
are preserved by the linker.
- syscall_weakdefs_llext.c contains the weak definitions for all syscalls.
This file is compiled in a separate library that is linked last, so
that the weak symbols are only used if no other implementation is
available.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
In current implementation, the SDP response packet will be ignored if
the operation code is `BT_SDP_ERROR_RSP`. And the SDP transaction
request is done, but the application is not notified. And the pending
SDP transaction cannot be processed.
Notify application with empty buffer if the operation code is
`BT_SDP_ERROR_RSP`. And process the pending SDP transaction.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
The discovered SDP record of service attribute transaction response
cannot notified correctly. There is an error returned from function
`get_record_len()`.
For service attribute transaction response, only one attribute list
is returned. So the total record length is the buffer length. Return
buffer length directly from `get_record_len()` to fix the issue.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
This commit replaces the assignment of IS_ENABLED(x) macros to
various variables with direct condition checking. This should fix the
coverity issue and also promotes more uniformity in code.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
