Remove hard-coded clock values from device tree nodes,
instead read the clock values from the clock controller
during run time.
Signed-off-by: Girisha Dengi <girisha.dengi@intel.com>
The actual clock speed of the bus is partially determined by the
rising/falling edges of the SCL. These settings allow applications
to tune the clock based on board characteristics.
Signed-off-by: Corey Wharton <xodus7@cwharton.com>
Add a clk48Mhz node to the stm32f412 serie.
This clock is sourced by PLL_Q (default) or PLLI2S_Q
That 48MHz clock is used by the USB /SDMMC/RNG peripherals.
The sdmmc/SDIO clock is sourced by this CK48 (default)
or by the SYSCLOCK.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add power domains for EDMA0's channels 6, 7, 14, and 15.
For QM these are identified as IMX_SC_R_DMA_2_*, while
for QXP thy are identified as IMX_SC_R_DMA_0_*.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
This has no address space and doesn't belong between peripheral
nodes. Move it up the DTSI for better visibility. No functional
change.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
imx8qm and imx8qxp have a couple of differences regarding
the peripheral address spaces and how the DT nodes are
configured, which is why using a generic DTSI (nxp_imx8.dtsi)
for the both of them is not right.
One of the differences between the two, which affects Zephyr
is the fact that irqstr's address space is different. Up until
now this has been dealt with at the board level (i.e:
imx8qxp_mek_mimx8qx6_adsp.dts), which is not right as this is not
board-specific, but rather soc-specific. Additionally, this
causes the following warning during compilation:
"unit address and first address in 'reg' (0x51080000) don't
match for /interrupt-controller@510a0000"
To fix this, add two new DTSIs: nxp_imx8qm and nxp_imx8qxp.
Each board (i.e: imx8qm_mek and imx8qxp_mek) will have to include
the DTSI for their soc instead of the generic DTSI (i.e: nxp_imx8).
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
The Microchip CAP12xx series are available in 3, 6 or 8 channel versions.
Co-authored-by: Benjamin Cabé <kartben@gmail.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
The reg address was not equal to the one in the node name, producing
a build warning.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Set AMP dts nodes (ipm, mbox, ...) to use fixed locations in reserved
memory areas. Those areas memories are delimited in the `memory.h`.
Size of the occupied areas can be calculated but the dts nodes addresses
needs to be set manually in every case.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
This is the initial commit to support UART driver for Renesas RZ/G3S.
The driver only implements polling API for minimal support.
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Signed-off-by: Binh Nguyen <binh.nguyen.xw@renesas.com>
This is the initial commit to support pinctrl driver for Renesas RZ/G3S
Signed-off-by: Quang Le <quang.le.eb@bp.renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
This adds minimal support for a new SoC Renesas RZ/G3S
Signed-off-by: Tien Nguyen <tien.nguyen.zg@renesas.com>
Signed-off-by: Nhut Nguyen <nhut.nguyen.kc@renesas.com>
Signed-off-by: Binh Nguyen <binh.nguyen.xw@renesas.com>
This commit adds the main DTS configurations required
to enable I3C support on STM32.
Signed-off-by: Mohammad Badawi <zephyr@exalt.ps>
Signed-off-by: Sara Touqan <zephyr@exalt.ps>
LJ packages have 16 ADC channels vs 8 for SZ packages. Enhance
devicetree to account for this as well as conditional defines/code.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Due to Apollo3's internal bootloader, zephyr build is not able
to create correct flash address on linker.cmd while using
mcuboot. The PR configures flash-controller start address
to solve this problem.
Test board: rakwireless/rak11720
Test project: samples/subsys/mgmt/mcumgr/smp_svr
Signed-off-by: Sercan Erat <sercanerat@gmail.com>
This patch refactors the power management initialization for the SSP
driver across ACE15, ACE20, and ACE30 generations to align with the
recommended practices outlined in the documentation. The changes
include:
1. Replacing the conditional initialization of power management state
with a call to `pm_device_driver_init` in the `ssp_init` function.
2. Adding the `zephyr,pm-device-runtime-auto` property to the SSP nodes
in the device tree files for ACE15, ACE20, and ACE30.
3. Moving the power domain assignment for the SSP device in the device
tree. The previous configuration resulted in the device not being under
any power domain and being initialized as always ON.
These changes ensure that the SSP driver is initialized with the
appropriate power management state and that runtime power management is
automatically enabled based on the device tree configuration. The
functionality of the power management state remains unchanged, ensuring
consistent behavior.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This patch refactors the power management initialization for the DMIC
driver across ACE15, ACE20, and ACE30 generations to align with the
recommended practices outlined in the documentation. The changes
include:
1. Replacing the conditional initialization of power management state
with a call to `pm_device_driver_init` in the
`dai_dmic_initialize_device` function.
2. Adding the `zephyr,pm-device-runtime-auto` property to the DMIC nodes
in the device tree files for ACE15, ACE20, and ACE30.
These changes ensure that the DMIC driver is initialized with the
appropriate power management state and that runtime power management is
automatically enabled based on the device tree configuration. The
functionality of the power management state remains unchanged, ensuring
consistent behavior.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This patch addresses several issues with the Intel ADSP HDA DMA driver:
1. Refactors the HDA DMA power management initialization. The previous
use of `pm_device_runtime_enable` was incorrect. The updated approach
relies on enabling runtime power management through the device tree
using the `zephyr,pm-device-runtime-auto` property. Additionally, the
patch removes redundant device initialization steps as these are already
handled by `pm_device_driver_init` when the device is under a power
domain.
2. Corrects the power domain assignment for the HDA link. The HDA link
was previously assigned to the io0 power domain based on a
misinterpretation of the documentation. The correct power domain
assignment is now based on updated documentation for LNL, ensuring that
the HDA link is associated with the appropriate power domain.
These changes ensure that the HDA DMA driver properly manages power
states, reducing power consumption and improving system stability, while
ensuring the correct power domains are used.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
This patch addresses the following issues with the Intel HDA DAI driver:
1. Adds power management support for the HDA DAI driver by implementing
the `hda_pm_action` function and integrating it with the Zephyr power
management framework.
2. Ensures balanced calls to `pm_device_runtime_get` and
`pm_device_runtime_put` by modifying the `probe` and `remove`
functions to use these power management calls.
3. Ensures that the io0 power domain is active when the HD Audio is in
use by assigning the correct power domain to the HDA DAI devices in
the device tree files for various Intel ADSP platforms (ace15_mtpm,
ace20_lnl, ace30, ace30_ptl).
4. Enables runtime power management for the HDA DAI devices by adding
the `zephyr,pm-device-runtime-auto` property in the device tree.
These changes ensure that the HDA DAI driver properly manages power
states, reducing power consumption and improving system stability, while
ensuring the io0 power domain is active when required.
Signed-off-by: Tomasz Leman <tomasz.m.leman@intel.com>
Many MIPI DBI displays support a "tearing effect" signal, which can be
configured to signal each v-sync or h-sync interval. This signal can be
used by the MIPI DBI controller to synchronize writes with the
controller, and avoid tearing effects on the screen (which occur when
the write pointer from the MCU overlaps with the panel's read pointer in
the display controller's graphics RAM).
Add the `mipi_dbi_configure_te` API, which allows display controllers to
configure MIPI DBI controller to wait for a TE edge before streaming
display data. Allow the tearing enable parameters to be configured via
devicetree settings, since these will vary based on the MIPI DBI
controller and display controller in use.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename "nxp,kinetis-lpuart" compatible to "nxp,lpuart" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Introduce new binding "st,stm32u5-otghs-phy" for OTG_HS PHY. This allows to
configure clock source and handle STM32U5 specific OTG_HS PHY behavior in
driver implementation in a more readable way.
Move OTG_HS PHY clock selection (previously <&rcc STM32_SRC_HSI48
ICKLK_SEL(0)>) from OTG_HS node to OTG_HS PHY node.
Rename USBPHYC_SEL -> OTGHS_SEL which matches the definition in the stm32u5
CCIPR2 register (RM0456 Rev 5, Section 11.8.47).
Support enabling OTG_HS PHY clock, which is bit 15 (OTGHSPHYEN) in
RCC_AHB2ENR1. Change OTG_HS clock to be bit 14 (OTGEN).
Calculate in runtime OTG_HS PHY clock source frequency. Try to match that
to supported (16, 19.2, 20, 24, 26, 32 MHz) frequencies and select proper
option with HAL_SYSCFG_SetOTGPHYReferenceClockSelection() API (instead of
hardcoded 16 MHz selection).
Co-authored-by: Adrian Chadd <adrian.chadd@meta.com>
Signed-off-by: Adrian Chadd <adrian.chadd@meta.com>
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Support specifying divided clock buses by introduction of
STM32_CLOCK_DIV(div) macro. This macro can be used in devicetree to define
clock source of peripherals.
HSE is selected in devicetree using:
<&rcc STM32_SRC_HSE ...>;
HSE/2 can now be selected with:
<&rcc (STM32_SRC_HSE | STM32_CLOCK_DIV(2)) ...>;
This allows to use clock_control_get_rate() API in peripherals in order to
get desired clock rate.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Catch the DTS warning by copying the SDRAM node in description:
unit address and first address in 'reg' (0xc000000) don't match for
/sdram@c0000000
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
for the brevity renaming direction_gpios to dir_gpios since STEP/DIR
interface is quite an established term in context of stepper controllers.
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Additional bindings to configure SPI support.
Added new DTS option for data/IRQ sharing
Clarify default in driver DTS binding
Signed-off-by: Steve Boylan <stephen.boylan@beechwoods.com>
