Use NRF_DT_GPIOS_TO_PSEL() in calls to nRF GPIO HAL functions as they
need a psel value, a pin number combined with the corresponding GPIO
port number, not only the pin number as provided by DT_GPIO_PIN().
This way buttons connected to pins in the P1 port can also be handled
properly.
Replace also DT_NODELABEL(button0) with DT_ALIAS(sw0) for consistency
with other samples that use the standard button.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To give control over GPIO pins for Direction Finding Extension of
Radio peripheral when build for nRF53 network core, the application
core has to assign those pins to network core.
There is a mechanism that uses a device tree overlay to get
information about GPIO pins to be assigned to network core.
The commit adds overlays with appropriate configuration
to assign GPIO pins in all DF related samples.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
As the receive window is now decreased at the TCP module level, other
direct net_context users are also responsible for acknowledging the
received data with net_context_update_recv_wnd() - otherwise, the
communication will stall.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The capabilities callback did not provide information about
the type of the endpoint being configured, making it
impossible for the application to determine if it is a
sink or source endpoint.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Audio streams as defined by the BAP spec does not
support bidirectional audio streams. This commit
updates the API and implementation to match that.
The use a bidirectional CIS with 2 audio stream will
be added in a future commit.
This removes the _IN_ and _OUT_ and _INOUT_ QOS
values, as well as the direction of the codec QOS
struct.
To keep direction for internal use, the direction
has been added to the endpoint struct.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Make it consistent for audio.h and capabilities.h that the
array size parameter appear after the array parameter.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This enables CONFIG_LOG_BACKEND_UART_OUTPUT_DICTIONARY so that
the UART backend is in dictionary logging mode.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Reserve the upper 8 bits of gpio_dt_flags_t for SoC specific flags and
move the non-standard, hardware-specific GPIO devicetree flags (IO
voltage level, drive strength, debounce filter) from the generic
dt-bindings/gpio/gpio.h header to SoC specific dt-bindings headers.
Some of the SoC specific dt-bindings flags take up more bits than
necessary in order to retain backwards compatibility with the deprecated
GPIO flags. The width of these fields can be reduced/optimized once the
deprecated flags are removed.
Remove hardcoded use of GPIO_INT_DEBOUNCE in GPIO client drivers. This
flag can now be set in the devicetree for boards/SoCs with debounce
filter support. The SoC specific debounce flags have had the _INT part
of their name removed since these flag must be passed to
gpio_pin_configure(), not gpio_pin_interrupt_configure().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The overlay are defined to run the samples application with PWM
feature on the nucleo_l073rz,nucleo_f091rc, nucleo_g474re
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The metairq sample sometimes failed due to stuck because it has a
potential race when recording the latencies. The previous solution
checks whether the stats.mirq greater than MAX_EVENT. But stats.mirq
might also have a race here. So we change to check the msg sequence,
its correctness ensured by the kernel's message queue.
And also remove the spinlock in previous fix because tests only use
1 CPU, no need to add this. It also improves the fix for #40889,
to prevent test failed sporadically on acrn_ehl_crb and ehl_crb.
Fix#42874.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
According to Kconfig guidelines, boolean prompts must not start with
"Enable...". The following command has been used to automate the changes
in this patch:
sed -i "s/bool \"[Ee]nables\? \(\w\)/bool \"\U\1/g" **/Kconfig*
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add build assertions that will ensure that every peripheral for
which a driver instance is created has some pins assigned to it.
Neither pinctrl-0 nor *-pin properties can be currently marked as
required in devicetree, so these assertions will help users avoid
invalid configurations where it could be hard to figure out why
the UART is not working.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Pinnacle 100 DVK uses QSPI to store slot1 partition.
Add board config overlay to ensure QSPI is enabled
so slot1 can be read/written.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
This sample application uses the STM32 USB TCPC Driver to create a USBC
Sink Application for the STM32G081b_eval board.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
the icm42605 defaults to a global thread for trigger processing,
the CONFIG_ICM42605_TRIGGER_OWN_THREAD is deprecated.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Add the support of a rpmsg tty channel that responds to the generic
Linux rpmsg_tty driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Restructure to separate the management of the rpmsg stack
add the rpmsg client into 2 threads.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
The Bluetooth HCI driver based on the RPMsg transport now uses the IPC
service module. The compatible Bluetooth sample - HCI RPMsg - has also
been migrated to the new IPC solution.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Kconfig options now belong to the Kconfig domain, therefore, the
:kconfig:option: role needs to be used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This file defines the crypto driver API, cipher is supposed to be just
one type of capability (other can be hash) of these drivers, just
change the file name to be consistent with it.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Differentiate integration)platforms list per each sample test.
Removed sample.mcumg.smp_svr.bt_tiny as it can not fit in
nr51422 flash anymore, even with configuration tweeks.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The sample cannot spin in an infinity loop because the idle thread will
not run and consequently the forced state will not be used.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
By default, the Connection Parameters control feature is enabled for the
SMP Server sample with the Bluetooth transport.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
The callbacks were implemented to notify the application
about the state of the ISO. However, since then, callbacks
such as `started` and `stopped` have been implemented,
and as such the `connected` and `disconnected` callbacks
no longer server any purpose.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add a new board to support Intel Tiger Lake H PCH variant of cAVS2.5.
Move common Kconfig options for cavs25 to soc level. No need to
replicate these for every board.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
sensor_value_from_double had a early overflow when converting the
fractional part (val2). This occured when input was more then
2147.493647 (inp >= INT32_MAX/1000000.0 + 0.01).
return value -ERANGE as this is what errno is set to by `strtod` and
similar posix functions.
fixes issue #39176
Signed-off-by: Simon Frank <simon.frank@lohmega.com>
Add a couple of extra shield configurations to catch regressions with
the st7735r, gd7965 and ls0xx drivers.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
- Filter out the remaining CAN tests if no zephyr,canbus chosen node is
enabled in the devicetree.
- Rename the tests to shorten the name a bit.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
