Add an input driver for the modulino buttons module. This is a pluggable
I2C board implementing three buttons and three LEDs, the I2C protocol is
implemented on a microcontroller on the modulino board itself, the
firmware for that is open source and can be updated using an Arduino
sketch:
Link: https://github.com/arduino/node_modulino_firmware
Link: https://github.com/arduino-libraries/Modulino
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The VS1838B is one of the most found infrared receiver
found in electronic kits and is easy to setup with only
a single GPIO used for signal transmission (apart from
VCC and GND).
This new driver let applications use the VS1838B as an
input with events relayed as 0x0000<address><command>.
Only the NEC protocol is supported in this version but
more can be added later.
Link: https://github-wiki-see.page/m/CoreELEC/remotes/wiki/08.-NEC-IR-Protocol-Datasheet
This has been tested using the input_dump sample.
Signed-off-by: Bastien JAUNY <bastien.jauny@smile.fr>
Add a driver for the Nintendo Nunchuk, accessed through the I2C bus.
This driver only supports the joystick and the buttons, not the
accelerometer.
Signed-off-by: Miguel Gazquez <miguel.gazquez@bootlin.com>
Adds a way of reporting touchscreen events
taking common properties into account.
Signed-off-by: Dominik Lau <dlau@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The initial version of an input driver for Cirque Pinnacle ASIC supports:
* Setting sensitivity
* Choosing between relative and absolute modes
* Relative mode
* Primary tap
* Swapping X and Y
* Absolute mode
* Setting number of idle packets
* Clipping coordinates outside of active range
* Scaling coordinates
* Inverting X and Y coordinates
Signed-off-by: Ilia Kharin <akscram@gmail.com>
Convert the XEC keyboard scanning driver from kscan to input, add the
corresponding kscan compatibility node to the current board, build test
only.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add an initial input driver for the PixArt PAT9125EL, just core
functionalities for now, will add more configuration properties at a
later stage.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This commit introduces a driver for ADC keys, a common circuit design where
keys are connected to an ADC input via a resistor ladder.
Signed-off-by: Chen Xingyu <hi@xingrz.me>
Add an input driver to read data from an analog device, such as a
thumbstick, connected to an ADC channel, and report it as an input
device.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a device driver to read events from a Linux evdev device node and
inject them back as Zephyr input events.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the ITE keyboard scanning driver from kscan to input, add the
corresponding kscan compatibility node to the current board, build test
only.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
We currently have three keyboard scanning drivers in the code base
(npcx, it8xxx2 and mchp_xec, last two yet to be converted to input).
These have been largely copy pasted from each other and share a lot of
the same structure and code.
This PR lays a foundation to start decoupling feature from those drivers
into a common code base, and it is heavily inspired by the current
regulator common data/config one.
Feature wise this only moves the thread struct, stack and initialization
to the common code and declares the thread callback as the only API, but
the intent is to move as much code as possible in there an only abstract
device specific callbacks in the api structures.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the GT911 driver to the input subsystem, fix the existing boards
to work in the default config.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the XPT2046 driver to the input subsystem, change the api,
remove the callback and enable logic.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a GPIO based quadrature decoder driver that reports relative axes
movements using the input subsystem.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the NPCX keyboard scan driver to the input subsystem and add the
input to kscan compatibility driver to maintain functionality with the
current API.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the SDL driver to use the input subsystem. This is specifically
meant to emulate touchscreen drivers, so it's setup to send triplet of
x, y, touch for touch-on events and just touch off on touch off events.
Renamed the driver to input-sdl-touch since now we can also develop an
sdl driver for simulating key events.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the ft5336 to the input subsystem, fix all the config in the
repository and add the Kscan compatibility driver to the current dts
driver instances.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Port the gpio_keys_zephyr driver from the gpio subsystem with a
dedicated API to the input subsystem reporting input events.
Move the test as well, simplify the cases a bit since the API is simpler
now.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
