8c294995e0
This sample is often the first one used as reference for Bluetooth Mesh, so it should have a good configuration as a starting point. Comment out the LPN options to eliminate Kconfig warnings, since the LOW_POWER option they depend on is not enabled. Also disable INIT_STACKS since that's only needed for fine-tuning the app configuration, and otherwise only causes unnecessary spam in the console. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
73 lines
1.6 KiB
Plaintext
73 lines
1.6 KiB
Plaintext
#CONFIG_INIT_STACKS=y
|
|
CONFIG_MAIN_STACK_SIZE=512
|
|
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048
|
|
|
|
CONFIG_BT_SETTINGS=y
|
|
CONFIG_FLASH=y
|
|
CONFIG_FLASH_PAGE_LAYOUT=y
|
|
CONFIG_FLASH_MAP=y
|
|
CONFIG_FCB=y
|
|
CONFIG_SETTINGS=y
|
|
CONFIG_SETTINGS_FCB=y
|
|
|
|
CONFIG_BT_OBSERVER=y
|
|
CONFIG_BT_BROADCASTER=y
|
|
CONFIG_BT_CTLR_DUP_FILTER_LEN=0
|
|
CONFIG_BT_CTLR_LE_ENC=n
|
|
CONFIG_BT_CTLR_LE_PING=n
|
|
CONFIG_BT_DATA_LEN_UPDATE=n
|
|
CONFIG_BT_PHY_UPDATE=n
|
|
CONFIG_BT_CTLR_CHAN_SEL_2=n
|
|
CONFIG_BT_CTLR_MIN_USED_CHAN=n
|
|
CONFIG_BT_CTLR_ADV_EXT=n
|
|
CONFIG_BT_CTLR_PRIVACY=n
|
|
|
|
CONFIG_BT_PERIPHERAL=y
|
|
|
|
CONFIG_BT=y
|
|
CONFIG_BT_TINYCRYPT_ECC=y
|
|
CONFIG_BT_RX_BUF_COUNT=30
|
|
CONFIG_BT_L2CAP_RX_MTU=69
|
|
CONFIG_BT_L2CAP_TX_MTU=69
|
|
CONFIG_BT_L2CAP_TX_BUF_COUNT=5
|
|
|
|
CONFIG_BT_MESH=y
|
|
CONFIG_BT_MESH_RELAY=y
|
|
CONFIG_BT_MESH_LOW_POWER=n
|
|
CONFIG_BT_MESH_FRIEND=y
|
|
CONFIG_BT_MESH_FRIEND_QUEUE_SIZE=16
|
|
|
|
CONFIG_BT_MESH_PB_GATT=y
|
|
CONFIG_BT_MESH_PB_ADV=y
|
|
CONFIG_BT_MESH_GATT_PROXY=y
|
|
|
|
#CONFIG_BT_MESH_LPN_SCAN_LATENCY=30
|
|
#CONFIG_BT_MESH_LPN_RECV_DELAY=40
|
|
#CONFIG_BT_MESH_LPN_POLL_TIMEOUT=300
|
|
|
|
CONFIG_BT_MESH_SUBNET_COUNT=2
|
|
CONFIG_BT_MESH_APP_KEY_COUNT=2
|
|
CONFIG_BT_MESH_MODEL_GROUP_COUNT=2
|
|
CONFIG_BT_MESH_LABEL_COUNT=3
|
|
|
|
#CONFIG_BT_MESH_IV_UPDATE_TEST=y
|
|
|
|
#CONFIG_UART_CONSOLE=n
|
|
#CONFIG_BT_DEBUG_MONITOR=y
|
|
CONFIG_BT_DEBUG_LOG=y
|
|
|
|
CONFIG_BT_MESH_DEBUG=y
|
|
#CONFIG_BT_MESH_DEBUG_PROV=y
|
|
#CONFIG_BT_MESH_DEBUG_PROXY=y
|
|
#CONFIG_BT_MESH_DEBUG_BEACON=y
|
|
CONFIG_BT_MESH_DEBUG_NET=y
|
|
CONFIG_BT_MESH_DEBUG_TRANS=y
|
|
CONFIG_BT_MESH_DEBUG_SETTINGS=y
|
|
#CONFIG_BT_MESH_DEBUG_LOW_POWER=y
|
|
CONFIG_BT_MESH_DEBUG_FRIEND=y
|
|
#CONFIG_BT_MESH_DEBUG_MODEL=y
|
|
#CONFIG_BT_MESH_DEBUG_ACCESS=y
|
|
#CONFIG_BT_MESH_DEBUG_CRYPTO=y
|
|
#CONFIG_BT_MESH_DEBUG_ADV=y
|
|
#CONFIG_BT_MESH_SELF_TEST=y
|