zephyr

History

Torsten Rasmussen 407b49b35c cmake: use find_package to locate Zephyr Using find_package to locate Zephyr. Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate code. Whenever an automatic run of CMake happend by the build system / IDE then it was required that ZEPHYR_BASE was defined. Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to cache the base variable and thus allowing subsequent invocation even if ZEPHYR_BASE is not set in the environment. It also removes the risk of strange build results if a user switchs between different Zephyr based project folders and forgetting to reset ZEPHYR_BASE before running ninja / make. Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>		2020-03-27 16:23:46 +01:00
..
src	coccinelle: standardize k_sleep calls with integer timeouts	2019-10-09 08:38:10 -04:00
CMakeLists.txt	cmake: use find_package to locate Zephyr	2020-03-27 16:23:46 +01:00
nrf52840dk_nrf52840.overlay	boards: nrf52840_pca10056: Rename board to nrf52840dk_nrf52840	2020-03-27 09:14:08 +01:00
prj.conf
README.rst	boards: nrf52840_pca10056: Rename board to nrf52840dk_nrf52840	2020-03-27 09:14:08 +01:00
sample.yaml	boards: nrf52840_pca10056: Rename board to nrf52840dk_nrf52840	2020-03-27 09:14:08 +01:00

README.rst

.. _bme680:

BME680: Integrated environmental sensor
#####################################################

Description
***********

This sample application periodically (every 3s) measures the ambient temperature
in degrees Celsius, atmospheric pressure in kilopascal, relative humidity in percentage,
and gas sensor resistance in ohms. The result is written to the console.

References
**********

 - BME680: https://www.bosch-sensortec.com/bst/products/all_products/bme680

Wiring
*******

This sample uses the BME680 sensor controlled using the I2C interface.
Connect Supply: **VDD**, **VDDIO**, **GND** and Interface: **SDA**, **SCL**.
The supply voltage can be in the 1.8V to 3.6V range.
Depending on the baseboard used, the **SDA** and **SCL** lines require Pull-Up
resistors.

Building and Running
********************

This project outputs sensor data to the console. It requires a BME680
sensor. It should work with any platform featuring a I2C peripheral interface.
It does not work on QEMU.
In this example below the :ref:`nrf52840dk_nrf52840` board is used.


.. zephyr-app-commands::
   :zephyr-app: samples/sensor/bme680
   :board: nrf52840dk_nrf52840
   :goals: build flash

Sample Output
=============

.. code-block:: console

   Device 0x20002b74 name is BME680
   T: 23.988877; P: 97.648568; H: 53.689533; G: 1035.211466
   T: 24.168500; P: 97.648866; H: 53.565966; G: 1046.677896
   T: 24.336533; P: 97.648596; H: 53.353663; G: 1058.656533
   T: 24.589696; P: 97.648366; H: 53.958864; G: 1072.155863
   T: 24.856631; P: 97.648322; H: 53.553669; G: 1096.448788

   <repeats endlessly>