19dee0e937
add test for reconfigure, release, suspend, abort and disconnect. app_config_req and app_reconfig_req always accept the req, so don't need to handle reject case. Signed-off-by: Mark Wang <yichang.wang@nxp.com>
103 lines
4.7 KiB
ReStructuredText
103 lines
4.7 KiB
ReStructuredText
Bluetooth: A2DP Shell
|
|
#####################
|
|
|
|
The :code:`a2dp` command exposes parts of the A2DP API.
|
|
|
|
The following examples assume that you have two devices already connected.
|
|
|
|
Here is a example connecting two devices:
|
|
* Source and Sink sides register a2dp callbacks. using :code:`a2dp register_cb`.
|
|
* Source and Sink sides register stream endpoints. using :code:`a2dp register_ep source sbc` and :code:`a2dp register_ep sink sbc`.
|
|
* Source establish A2dp connection. It will create the AVDTP Signaling and Media L2CAP channels. using :code:`a2dp connect`.
|
|
* Source and Sink side can discover remote device's stream endpoints. using :code:`a2dp discover_peer_eps`
|
|
* Source or Sink configure the stream to create the stream after discover remote's endpoints. using :code:`a2dp configure`.
|
|
* Source or Sink establish the stream. using :code:`a2dp establish`.
|
|
* Source or Sink start the media. using :code:`a2dp start`.
|
|
* Source test the media sending. using :code:`a2dp send_media` to send one test packet data.
|
|
* Source or Sink suspend the media. using :code:`a2dp suspend`.
|
|
* Source or Sink release the media. using :code:`a2dp release`.
|
|
|
|
.. tabs::
|
|
|
|
.. group-tab:: Device A (Audio Source Side)
|
|
|
|
.. code-block:: console
|
|
|
|
uart:~$ a2dp register_cb
|
|
success
|
|
uart:~$ a2dp register_ep source sbc
|
|
SBC source endpoint is registered
|
|
uart:~$ a2dp connect
|
|
Bonded with XX:XX:XX:XX:XX:XX
|
|
Security changed: XX:XX:XX:XX:XX:XX level 2
|
|
a2dp connected
|
|
uart:~$ a2dp discover_peer_eps
|
|
endpoint id: 1, (sink), (idle):
|
|
codec type: SBC
|
|
sample frequency:
|
|
44100
|
|
48000
|
|
channel mode:
|
|
Mono
|
|
Stereo
|
|
Joint-Stereo
|
|
Block Length:
|
|
16
|
|
Subbands:
|
|
8
|
|
Allocation Method:
|
|
Loudness
|
|
Bitpool Range: 18 - 35
|
|
uart:~$ a2dp configure
|
|
success to configure
|
|
stream configured
|
|
uart:~$ a2dp establish
|
|
success to establish
|
|
stream established
|
|
uart:~$ a2dp start
|
|
success to start
|
|
stream started
|
|
uart:~$ a2dp send_media
|
|
frames num: 1, data length: 160
|
|
data: 1, 2, 3, 4, 5, 6 ......
|
|
uart:~$ a2dp suspend
|
|
success to suspend
|
|
stream suspended
|
|
uart:~$ a2dp release
|
|
success to release
|
|
stream released
|
|
|
|
.. group-tab:: Device B (Audio Sink Side)
|
|
|
|
.. code-block:: console
|
|
|
|
uart:~$ a2dp register_cb
|
|
success
|
|
uart:~$ a2dp register_ep sink sbc
|
|
SBC sink endpoint is registered
|
|
<after a2dp connect>
|
|
Connected: XX:XX:XX:XX:XX:XX
|
|
Bonded with XX:XX:XX:XX:XX:XX
|
|
Security changed: XX:XX:XX:XX:XX:XX level 2
|
|
a2dp connected
|
|
<after a2dp configure of source side>
|
|
receive requesting config and accept
|
|
sample rate 44100Hz
|
|
stream configured
|
|
<after a2dp establish of source side>
|
|
receive requesting establishment and accept
|
|
stream established
|
|
<after a2dp start of source side>
|
|
receive requesting start and accept
|
|
stream started
|
|
<after a2dp send_media of source side>
|
|
received, num of frames: 1, data length: 160
|
|
data: 1, 2, 3, 4, 5, 6 ......
|
|
<after a2dp suspend of source side>
|
|
receive requesting suspend and accept
|
|
stream suspended
|
|
<after a2dp release of source side>
|
|
receive requesting release and accept
|
|
stream released
|
|
...
|