This commit resolves an internal dependecy between GET_DIRECTION and
GET_CONFIG configuration. GET_CONFIG api is internally needed by
GET_DIRECTION api.
Signed-off-by: Martin Kiepfer <m.kiepfer@teleschirm.org>
The Nuvoton NCT38xx is a multi-function device providing a TCPC
controller and a I/O expander (GPIO driver). Add a multi-function
driver to manage exclusive access to the device.
Tested with "twister -T tests/drivers/build_all/gpio".
Signed-off-by: Keith Short <keithshort@google.com>
the sam xdmac driver does not yet implement the
get_status() function. with this commit the function
will be implemented. Fixes#62003
Signed-off-by: Sven Ginka <sven.ginka@gmail.com>
Seems like the SSD1306 controller needs a bit of time after power up
before it can take i2c commands. This causes problems with
microcontrollers that have no other delays in the startup sequence, like
rpi_pico.
There's currently no good way of modeling this in Zephyr right now, and
there's also no clear indication of how much time the device needs in
the datasheet that I could find, but it seems like 10ms is enough for
that to start reliably so add a delay in the ssd1306 init function to
ensure that at least that time has passed from system power up.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Remove `threshold-reg-offset` DT property and implement them with static
inline functions in `reg_def.h`
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add `thr-sel` prop. to select the relevant threshold register for adc
comparator since there're two adc modules in npcx4 series.
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add multi-device support in npcx adc driver since there is more than one
adc module in npcx4 series. And each adc's reference voltage might be
different, this CL introduces the `vref-mv` prop. to select its own
reference voltage.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Only provide implementations for optional operations if needed. This
patch deletes quite a few dummy `pin_interrupt_configure` ops (now
optional), and adjusts ifdeffery on some drivers so that optional ops
are only provided if they implement real functionality.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This change allows to have GPIO interrupts configured
that will work while chip enters low power modes where
PD_COM is turned off.
PDC controller can wake up system on GPIO changes even when
PD_COM is off.
This is done by adding PDC entries that will wakeup Cortex-M33
at the same time when WAKEUP controller is programmed to
handle GPIO state changes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Hardware supports only one edge for GPIO interrupt.
This adds software implementation that hides hardware restriction.
With this change user code can use GPIO_INT_TRIG_BOTH and does not
have to do it in application code.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Init level for GPIO drivers is set PRE_KERNEL_1.
Smartbond(tm) driver had it set to POST_KERNEL by accident.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Fix the whole v_empty setting code, this was using a wrong scaling
factor, but also incorrectly clearing the recovery voltage part of the
register.
Change the code to read the previous value and mask out the bits not
used by VE.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Introduce I2C target transfer using the PIO mode. Add an option
"target-pio-mode" in the yaml file, determined by the DTS, to dictate
whether I2C target transfer uses the PIO mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Disable the timeout setting when both the clock and data are
in a low state. This allows for I2C host clock stretching
without a timeout limit.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
IT8XXX2_I2C_STR is a register of read-only, non-writable to clear.
Here we can set hardware reset bit in the IT8XXX2_I2C_CTR register
to clear the status of IT8XXX2_I2C_STR.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The old acpi implimentation is replaced with acpica interface
and updated x86 arch porting with the new interface.
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
Previously the pwm capture only support capturing on channel 1
and 2, because the slave mode controller was used, which uses
the signal TIxFP which is not available for channel 3 and 4.
This commit adds optional support for four channel capturing by
changing the method of capturing PWM signals to not use the
slave mode controller to reset the counter register. Instead the
counter is reset in the ISR. This will result in a slight loss
of accuracy but is still within an acceptable range.
Co-authored-by: Jeroen van Dooren <jeroen.van.dooren@nobleo.nl>
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
This commit adds option to dump i2c messages of only specified
devices. It makes it easier to debug communication of specific
i2c device instead of logging all i2c communication.
The filter of devices is specifiec in device-tree using the
node with "zephyr,i2c-dump-filter" compatible string.
Example of device-tree node:
i2c-dump-filter {
compatible = "zephyr,i2c-dump-filter";
devices = < &display0 >, < &sensor3 >;
};
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit changes the format of printed messages to align the
following strings and make it more readable.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit changes the parameter of i2c_dump_msgs function from
string name to pointer to the device structure.
It allows for comparison of device pointers and allow to use
the printed device name in i2c shell commands.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
LOG_LEVEL > LOG_LEVEL_OFF guards were protecting a couple of function
declarations. These functions were being used without taking this fact
into consideration. These guards are now applied around the stack_stats()
function only.
Signed-off-by: Diogo Correia <diogo.correia@fraunhofer.pt>
This introduces PWM driver with supporting PWM output
APIs based on NXP S32 EMIOS peripheral. This supports
three mode: OPWFMB, OPWMCB and OPWMB.
OPWFMB uses internal counter, the new period and duty
cycle takes effect immediately.
OPWMCB and OPWMB use external counter as timebase, changing
PWM period at runtime will impact to all channels share the
same timebase. Also the new period and duty cycle take effect
in next period boundary of the timebase
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This PR adds a misc driver for NXP S32 eMIOS peripheral.
eMIOS provides multiple unified channels (UCs), there are
several channels can be used as reference timebase
(master bus) for other channels. At this time, the
driver does initialize global configuration for eMIOS
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
This commit improves the usage of the bus pipe (connected
to UART) to only open it when the modem is actually
powered and ready, not when leaving the idle state. This
ensures the pipe is flushed before sending the init script,
and re-enables the UART driver if it is disabled due to
errors.
While building a test platform based on the nRF9160 and a
Quectel BG95, it was discovered that the nRF9160 correctly
throws UART errors if the RX is enabled while the UART RX
line is low (which was due to the modem being powered
down).
The improvements should also help help remove the
"<wrn> modem_chat: receive buffer overrun" warning which
would occur during startup as the pipe was opened, but
nothing was receiving the data, causing the buffer to
overflow.
Signed-off-by: Bjarki Arge Andreasen <bjarkix123@gmail.com>
Add support for device power management. When the sensor
is not powered, the fetch function will fail. When the
sensor is not connected to a power domain, it will behave
as usual.
Signed-off-by: Albert Jakieła <aja@semihalf.com>
`CONFIG_BT_L2CAP_TX_MTU` drives the maximum supported MTU on a Bluetooth
connection, but the SPI backend also imposes its own hidden limits.
Display a warning if a value is chosen that can result in failures to
send. This is done here instead of as a range on `BT_L2CAP_TX_MTU` as
ranges on that symbol are already defined in terms of software features,
which would conflict with this check.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
The eswifi spi driver sets up spi buffer length as number of frames,
but the length shall be number of bytes. Because eswifi use 16 bit as
frame size, so this turns out reading and writing half of data and
fails to sending any at command request and getting any responds from
eswifi module.
Fix it by setting up length as number of bytes.
Fixes#62056
Signed-off-by: Chien Hung Lin <chienhung.lin.tw@gmail.com>
Fix a shadow variable build error:
dmic_nhlt.c: In function 'dai_dmic_write_coeff':
dmic_nhlt.c:57:78: error: declaration of 'base' shadows a global
declaration [-Werror=shadow]
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Created set of new functions for configure fir coefficients with support
for packed format. This allowed to make the dai_dmic_set_config_nhlt
function simpler.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Added reading of a necessary register values in
dai_nhlt_dmic_dai_params_get function to simplify its parameter list. The
code that calculates dai_params has been moved to it to simplify the
dai_dmic_set_config_nhlt function.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
More verbose variable pdm_idx was used instead of n. The series of
references to the array of pdm base addresses has been replaced with
a pdm_base variable.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
All fir filters have an identical set of registers so their definitions
were combined to simplify the code. From the dai_dmic_set_config_nhlt
function, a duplicate piece of code responsible for configuring fir was
separated into a new function.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Created dai_dmic_start_fifo_packers function corresponding to an already
existing dai_dmic_stop_fifo_packers.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
The while loop in the code fragments waiting for a bit to be cleared has
been replaced with the WAIT_FOR macro call. Added a warning in the case of
timeout.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Added reading of a necessary register values in
dai_nhlt_dmic_dai_params_get function to simplify its parameter list. The
code that calculates dai_params has been moved to it to simplify the
dai_dmic_set_config_nhlt function.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
All PDM controllers have the same set of registers. Their definitions have
been merged to simplify the code.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Moved code fragments responsible for logging and verification of the
configuration register values from the dai_dmic_set_config_nhlt function to
a separate functions. Behavior of the code verifying the correctness of
register values has been changed so that it only displays warnings.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Definitions of a configuration blob structures were separated from the main
drivers header file and moved to a dedicated file to improve code
readability. Removed unnecessary nhlt_pdm_fir_coeffs structure.
The nhlt_pdm_ctrl_cfg structure was extended with nhlt_pdm_ctrl_fir_cfg
and fir coefficients.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
