Since fc007eeef5 TLS sockets support
timeout based on CONFIG_NET_SOCKETS_CONNECT_TIMEOUT value. The TLS test
suite reduced this config value to speed up the tests, however it turns
out the 100ms timeout is too low to finalize the handshake on slower
platforms (nrf52840 specifically). Therefore increase the timeout value
to 200ms to prevent test failures on those.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
As confirmable requests will stay allocated for (3 * ACK_TIMEOUT), we
need to adjust the timings so all requests are unallocated by the end
of the test.
Signed-off-by: Francois Gervais <francoisgervais@gmail.com>
Evaluate CONFIG_LINKER_ITERABLE_SUBALIGN in CMake instead of in the
linker script.
It cannot be assumed that a linker generator implementation is
pre-processed and therefore Kconfig settings cannot be used in those
but must be evaluated in CMake.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Since the same test might be run in parallel on different platforms,
the one that it's started later will fail due to port re-use for
the OpenSSL server.
Since it's not really required to run the tests on native_sim and
native_sim/native/64, the latter is removed in order to solve this
problem.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
native_posix is now deprecated.
Building these tests in both native_sim and native_posix does not
improve coverage for the tests or subsystem but doubles CI time.
As anyhow native_posix will be removed all together in
2 releases, let's remove it already for these.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Make sure it's possible to register IPv4/6 addresses on an offloaded
interface. Add an extra build configuration to make sure it's also
possible when native IP stack is disabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add test cases for dynamic GET/POST, where the payload is transferred
across more than one call to the dynamic resource callback.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
After introduction of struct http_response_ctx, the dynamic resource
data buffer is no longer needed for transferring data between the
application callback and the server. It is therefore removed to avoid
unnecessary copying of data.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
Add tests covering new method of providing a response for dynamic
resources.
Tests cover the application sending response codes and headers,
overriding "default" headers, and sending various combinations of
headers and body data. Each case is tested for HTTP1 & HTTP2, both POST
and GET methods.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
Allow the application to send headers and response codes from a dynamic
resource callback by filling out a response context structure.
This also allows simple requests to be completed in a single execution
of the callback, by setting the final_chunk flag.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
Ethernet board variant was missed in commit 138e9591f8 (tests: net:
wifi: exclude RW612 based boards), but is the sole variant that actually
was running this test. Exclude this variant only, since it cannot build
this test due to requiring binary blobs.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds a test to showcase how to configure TLS 1.2 and 1.3
socket connections against an OpenSSL server. Only a limited number
of combinations are available for now:
- TLS 1.2
- RSA certificate and key exchange.
- ECDSA certificate and ECDHE key exchange.
- TLS 1.3 only supports ephemeral (ECDHE) key exchange with/without
session tickets.
Since the goal is to test TLS connection and not low level ethernet
functionalities or similar, the only supported platform is "native_sim"
where Linux sockets are used to connect to the OpenSSL server locally.
The idea is that the Zephyr application acts a client and tries to connect
to the OpenSSL server running on the same PC. For sake of simplificity a
bash script is provided to start the OpenSSL server properly.
For completeness a bash script is also provided to re-generate
certificates and keys.
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This was seen in CI
START - test_cycle_ready_CC
Assertion failed at ...tests/net/conn_mgr_monitor/src/main.c:262:
cycle_ready_ifaces: (stats.conn_count_gen not equal to 1)
NET_EVENT_L4_CONNECTED should be fired when connectivity is gained.
FAIL - test_cycle_ready_CC in 0.015 seconds
As the event wait timeout is very short (1ms) by default, increase
it to 10ms so that we will not miss the event.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Move the network buffer tests to tests/lib/net_buf as their implementation
now lives outside of the networking subsystem.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Move the network buffer header file from zephyr/net/buf.h to
zephyr/net_buf.h as the implementation now lives outside of the networking
subsystem.
Add (deprecated) zephyr/net/buf.h header to maintain compatibility with old
file path.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Move the net_buf implementation from the networking subsystem to a library
as they have no dependency on the networking subsystem.
Network buffers are used in subsystems outside of networking
(e.g. Bluetooth, USB).
Fixes: #36374
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Allow application to register certain HTTP request headers to be stored
by the server. These stored headers can then be accessed from a dynamic
resource callback.
Signed-off-by: Matt Rodgers <mrodgers@witekio.com>
Exclude RW612 based boards from the WiFi testsuite, as these boards
require binary blobs be downloaded in order to build as expected
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Currently, the test doesn't clear the control data buffer before
calling recvmsg. This leads to recvmsg being unable to add the new
control data, which corresponds to the current received data.
This commit aims to clear the control data buffer to match most use
cases, when the control data buffer is empty before calling recvmsg.
Signed-off-by: Axel Le Bourhis <axel.lebourhis@nxp.com>
Add missing braces to comply with MISRA C:2012 Rule 15.6 and
also following Zephyr's style guideline.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
native_posix is deprecated, let's switch the
description & comments to refer to native_sim instead.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Convert users of net_buf_put() and net_buf_get() functions to use
non-wrapped putters and getters k_fifo_put() and k_fifo_get().
Special handling of net_bufs in k_fifos is no longer needed after commit
3d306c181f, since these actions are now
atomic regardless of any net_buf fragments.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The nrf7002dk board's wifi chip requires blobs to build wifi driver.
Therefore it can not be built by CI. Exclude the board and its
variants from the wifi test suite.
Signed-off-by: Bjarki Arge Andreasen <bjarki.andreasen@nordicsemi.no>
The MQTT publisher/subscriber/pubsub tests suites are currently
depending on an external MQTT broker being available. In result, the
test suites cannot be executed in twister and need to be run manually,
which makes them kind of pointless from the CI perspective.
This commit reworks the tests, so that they no longer rely on an
external broker being available, but rather implement minimalistic
broker functionality for test purposes only. This will make the tests
self contained, and thus executable in the CI.
Since it makes not point to duplicate the effort between the test
suites, the test suites have been merged into a single mqtt_client test
suite.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Currently existing tests suites verify MQTT 3.1.1 functionality,
therefore group them together under "mqtt/v3_1_1" directory, so
that the test base can be extended easily in the future with MQTT 5.0
tests without collision.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Fixes: #73831
find_package(Zephyr) should be called before first project() call.
Zephyr package will test and force-set the correct toolchain, especially
the C compiler.
The project() will also set the C compiler, if not set already.
If project() is called first, then conflict arises on the C compiler
selection and thus the following message is seen:
> You have changed variables that require your cache to be deleted.
> Configure will be re-run and you may have to reset some variables.
> The following variables have changed:
> CMAKE_C_COMPILER= /usr/bin/gcc
This cache deletion results in other errors, such as a missing BOARD
setting.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Tweak some Kconfig variables to reduce the overall memory footprint of
the test application. For some reason x86 MMu throws errors when
accessing iterable section entries when the image size is too large.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Beacon frames can be received with association permit bit set or not,
but the correct information should be in the data given to the
application.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
When trying to implement a testcase for the previous commit, an error
occoured, that stopped the test from executing.
As the tests require a full IPv6 stack, the usual router solicitation
(RS) messages will be scheduled by the net stack. To avoid conflict
with RS messages the active scan test must be kept shorter than one
second, otherwise a race condition with additional packages being
reported by the fake driver might occur.
Signed-off-by: Fabian Pflug <fabian.pflug@grandcentrix.net>
The HTTP server tests are self-contained, they do not require network
environment to execute, hence should not specify "harness: net".
The consequence of specifying the harness was that HTTP server tests in
the CI were only built, and not executed, which doesn't make much sense.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add test cases verifying that request containing header frame with
priority flag set is processed properly.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add tests cases covering interaction with dynamic resources with
POST/GET requests.
Simplify HTTP2 request generation to facilitate adding more tests.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add test case verifying that the server keeps the connection open if no
Connection: close header is present in the request.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Remove pointless helper functions, the test code can simply be included
in the test case w/o code duplication.
Clarify the naming of existing test cases. Backward compatibility simply
tests HTTP1. The upgrade test wasn't really testing HTTP upgrade, so
rename the test case too. Add a new test case actually verifying HTTP
upgrade.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Do some cleanup regarding naming used in the test suite to prepare it
for adding more test cases.
Extract common setup/teardown into respective before and after ztest
functions to simplify test code. Proper before and after functions also
ensure that individual test case failure does not disrupt other tests
operation.
Split the tests into two separate test suites, one for those which
require pre-setup and second for those which don't.
Finally, enable receive timeout on the client socket to ensure tests
won't stall in case of errors.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
"prototype" is ambiguous in this regard, as it doesn't really tell what
the test suite is testing. As tests in this test suite verify core HTTP
server functionality, rename it to "core".
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The test case for SO_BINDTODEVICE socket option was flaky, the client
socket always sent the datagram to the IP address of the second
interface, so in theory every packet should end up on that interface.
In practice though, due to imperfect loopback packet handling, the test
worked as the packet ended up on the interface it was sent from.
The test should send datagrams to the IP addresses of the interface 1
and 2 alternatively. The server socket binds to ANY address, so w/o
interface binding it should receive all datagrams, so it allows to
verify if SO_BINDTODEVICE filtering works fine.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
