Both nrf54l15pdk/cpuflpr and nrf54l15pdk/cpuflpr_xip have
watchdog on the list of supported periperals.
As a result, Twister tries to build samples/drivers/watchdog
for these two targets.
Since overlays are missing, build is failing.
Add missing overlay files.
Signed-off-by: Sebastian Głąb <sebastian.glab@nordicsemi.no>
RW612 has one FLEXSPI controller, which is capable of supporting
multiple external devices on one board. However, care must be taken when
configuring the FLEXSPI to use multiple devices, as if the FLEXSPI is
configured incorrectly in XIP mode it will fail to read from the
external flash, and the chip will crash.
Make the following changes to the RW configuration for the MEMC sample,
in order to support executing from flash while accessing PSRAM:
- initialize the FLEXSPI MEMC driver first, before the flash or PSRAM
drivers are initialized
- force the FLEXSPI MEMC driver to reconfigure the FLEXSPI at boot, so
we can configure the DQS sampling mode for the PSRAM on port B
- only configure the PSRAM pins during FLEXSPI init, so XIP is not
disrupted
- configure the flash device at boot. This is required so that the MEMC
driver will not replace the LUTs programmed in the FLEXSPI by the
bootrom, as it would otherwise not be aware of their existence.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The chain-length DTS property is now mandatory, so remove the
optional Kconfig for setting the length
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Adds chain length and colour mapping properties to LED strip devices
on boards where these parameters are now required
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Since the RW612 BGA board's FlexSPI configuration prevents the board
from executing from flash while the PSRAM is configured (unless both are
configured by a bootloader prior to XIP), run the MEMC sample from
internal code SRAM, and write data to the external PSRAM block via the
FlexSPI.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert the ht16k33 to use the input subsystem. This can still be used
with the kscan API with the zephyr,kscan-input driver, or use the
input-keymap one to generate input codes instead.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
VTILED displays with a height other than x8 fail to draw bottom-row
tiles. This is because it extends beyond the display area.
I fixed the drawing area to be cropped to fit within the display.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
The overlay for the mimxrt1062 boards gnss alias is pointing
to the uart node rather than the gnss node. Adjust gnss alias
and node naming.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
1) Replace master/slave in API for new terms in eSPI spec 1.5
2) Reflect eSPI VW change and macro changes across eSPI drivers
3) Update terms in eSPI driver sample and eSPI test driver
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add simple sample for the i2c target driver interface using the
i2c-target-eeprom as a target device.
Signed-off-by: Bram Vlerick <bram.vlerick@openpixelsystems.org>
Report more information and do not use `dev->name` so that what the
sample prints looks less similar to the GNSS dump logs.
Signed-off-by: Tomi Fontanilles <tomi.fontanilles@nordicsemi.no>
The adc sample was in the root directory of the adc samples.
Move all the files to a subdirectory adc_dt.
Signed-off-by: Paulo Santos <pauloroberto.santos@edge.ufal.br>
There are several esp32-based boards that its conf and overlay
files are missing proper renaming to match cpu cluster.
This also removes all _SOC_ name from files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
FTM internal counter can be clocked by one of three clock sources
independent of the module bus clock. This patch introduces a DT property
to perform the clock selection from DT.
DT sources are updated to keep the current clock selection for all boards,
with exception of ucans32k1sic board which is migrated to use system
clock by default, as this seems to be a better choice for most cases.
Some PWM LED samples require slower clock so overlays are added for
those cases.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add the overlay for the esp-wrover-kit, to drive a character display
based on HD44780 chipset using the I2C bus gpio controller PCF8574.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Enabled nxp lpadc driver acquisition time feature, the overlay file
can express acquisition time in microseconds, nanosecond and ADC
ticks.
The purpose of updating these overlay files is not only for local
testing, but also to remind users that they can use this feature.
Signed-off-by: Zhaoxiang Jin <Zhaoxiang.Jin_1@nxp.com>
After erasing the sector, compare dat read with expected 0xFF pattern
to decide if erasing is successful instead of relying on the
returned code of the flash_erase function
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The commit adds dependency on Kconfig FLASH_PAGE_LAYOUT to subsystems
that really require it:
FCB, NVS, LittleFS
and removes direct selection from '*.conf' files where no longer
needed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Adjustments of overlay and conf files to adjust for the MERGE removal.
The revert of MERGE requires specific overlay and conf files for boards
which relied on the MERGE feature.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Create regulator on GPIO for microphone supply
Set pdm data and clk pins in pinctrl
Add xiao_ble_sense overlay for dmic sample support
Signed-off-by: Zak Portnoy <zakportnoy@gmail.com>
Enable DMIC on RW612 BGA board. The DMIC is enabled for both onboard
MEMS microphones for this board, and the board is enabled with the DMIC
sample and test
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The sample wants to print the memory controller base address. However,
MEMC_BASE is used as argument in printf which is defined as long long
int. Use the memc pointer instead to print the base address.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The output example has not the correct indentation for the code-block
directive and therefore adds this output as normal text.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
During a memory mismatch, the sample only prints an error message.
Also print the read and write buffer to see the actual difference.
Moreover, add a print for each compare step to see the sample is still
running.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
MODEM_UBX: Adds Support for UBX Messages in Modem Subsystem.
GNSS API Supported: get_supported_systems, set_fix_rate, get_fix_rate,
set_enabled_systems, get_enabled_systems, set_navigation_mode,
get_navigation_mode.
Boards Tested: MIMXRT1062_FMURT6, VMU_RT1170.
Note: Partial support for U-BLOX Messages is provided as of now.
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
Signed-off-by: Mayank Mahajan <mayankmahajan.x@nxp.com>
Simplify this sample's recently updated configuration, and ensure that
the file suffix feature works in sysbuild.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
After https://github.com/zephyrproject-rtos/zephyr/pull/70438
got merged simultaneously with
https://github.com/zephyrproject-rtos/zephyr/pull/70564
all these tests stopped building properly due to the
change of avaliable variables in Kconfig & cmake.
Let's fix them.
As a bonus, as for kconfig the BOARD_TARGET_STRING is the
same for the hwmv1 backwards compatible name, let's
just remove the check for the old names.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Followup: #69905
Adopting new board terminology for CMake, python, and Kconfig code to
use qualifiers instead of identifiers.
Also adjusted to board target where applicable.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Replace all instances of
nrf5340bsim_nrf5340_cpunet & nrf5340bsim_nrf5340_cpuapp
with
nrf5340bsim/nrf5340/cpunet & nrf5340bsim/nrf5340/cpuapp
In these samples/tests twister yamls definitions.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
