Added support for fxas21002 sensor over SPI and I2C.
Made the fxas driver APIs generic for I2C and SPI.
Tested with fxas21002 sensor on RDDRONE.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Sumit Batra <sumit.batra@nxp.com>
Added support for fxos8700 sensor over SPI and I2C.
Made the fxos driver APIs generic for I2C and SPI.
Tested with fxos8700 sensor on RDDRONE.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Sumit Batra <sumit.batra@nxp.com>
The sensor uses the ALERT terminology (pin can be configured to trigger
on certain events such as conversion ready or overvoltage alerts). The
"IRQ" name is not clear.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the units of the current LSB in microamperes, so that we can
measure low maximum currents. Right now it was specified in
milliamperes, but ignored and always hardcoded to 1mA in the driver.
This makes the driver pretty much useless when the maximum current to be
measured is in a range of e.g. 20-50mA.
This patch also removes some unnecessary ifdeffery: since we write the
calibration register, we can always provice measurements with the right
units. It is also wrong to provide sensor readings that do not match
with the units specified by the channel. After this change voltage is
always reported in V, current in A and power in W.
Note that power measurement had the current LSB hardcoded in the
calculation (assuming 1mA/LSB), this has been fixed as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Following dtschema practices, add phyisical units to the shunt resistor
value: milliohms.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
With the recent introduction of DT_HAS* Kconfig helpers, such build
asserts are highly unlikely, so just remove them.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Driver had Doxygen stubs for sensor interface calls. First, most were
incomplete, outdated or just wrong. Second, implementations just need to
make sure to adhere to the error codes documented in the public
interface (sensor API in this case).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Add many missing includes so that headers are self-contained
- Sort includes properly (locals first, stdc, zephyr, etc.)
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Channel SENSOR_CHAN_GAUGE_FULL_CHARGE_CAPACITY was returned in place of
SENSOR_CHAN_GAUGE_FULL_AVAIL_CAPACITY, due to their matching names.
Ensuring that the channel names are unique fixes the issue.
Signed-off-by: Marco Argiolas <marco.argiolas@ftpsolutions.com.au>
Call lis2dw12_data_ready_mode_set() API in order to properly
set CLTR7.drdy_pulsed bit.
(Fix#51488)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Brackets were originally used in the sensor info shell command output to
make it obvious when a field is a null string, however they incorrectly
suggest that a field is an array. Remove the brackets and conditionally
print "(null)" instead.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Adds a new conditional shell command to the sensor shell to get data
from the sensor info iterable section, such as vendor and model name,
for all sensors.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Adds an iterable section in ROM to hold constant information, such as
vendor and model name, for all enabled sensor driver instances. This
will be used by the future sensor subsystem to enumerate all available
sensors in the system.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Refactors all sensor drivers to use SENSOR_DEVICE_DT_INST_DEFINE, which
is a sensor-specific variant of DEVICE_DT_INST_DEFINE that provides a
common place to instantiate additional data structures for the future
sensor subsystem and/or sensor driver stats.
This approach was inspired by I2C_DEVICE_DT_INST_DEFINE to streamline
adding I2C stats support across all I2C drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Without this define, the structure iis2dh_device_config
is defined incorrectly.
The structure is defined in iis2dh.h file as follows:
struct iis2dh_device_config {
struct spi_dt_spec spi;
struct i2c_dt_spec i2c;
uint8_t pm;
struct gpio_dt_spec int_gpio;
};
without the macro
the structure is defined as
struct iis2dh_device_config {
uint8_t pm;
struct gpio_dt_spec int_gpio;
};
which results in accessing the wrong data when
calling iis2dh_init_interrupt
function (or any other functions in this file)
Signed-off-by: Mehdi Zemzem <mehdi.zemzem2@gmail.com>
ADC comparator driver submits notifications into system work queue, this
change will make driver to use dedicated work queue instead by using
`CONFIG_ADC_CMP_NPCX_WORKQUEUE`.
Dedicated work queue and priority are configurable as well.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
The inactivity time registers identified by `ADXL362_REG_TIME_INACT_L`
and `ADXL362_REG_TIME_INACT_H` accepts a 16-bit value. (8 in each).
Without this change the last 5 bits of the register value
will be cleared.
Clearing the last bits of the register value greatly reduces the maximum
inactivity time that can be set.
Signed-off-by: Simen S. Røstad <simen.rostad@nordicsemi.no>
Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The build of this driver fails when `CONFIG_NO_OPTIMIZATIONS=y` is set:
error: expression in static assertion is not constant
98 | BUILD_ASSERT(steps > 0, "only positive number valid");
error: expression in static assertion is not constant
99 | BUILD_ASSERT(steps <= 2048, "overflow possible");
Fix this by using a simple macro to avoid the compiler from getting
confused.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added support for the AMS AS621x series of temperature sensors as a
variant of the TI TMP108 temperature sensor.
Signed-off-by: Jared Baumann <jared.baumann8@t-mobile.com>
Signed-off-by: James Johnson <james.johnson672@t-mobile.com>
Add 2 properties to configure the "any movement" event.
* Ability to disable the interrupt latch
* Select movement mode
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
On power on reset, after disable advanced power safe mode,
you need to wait a delay before write again in the device.
The missing wait produce random initialization failure.
See §4.4 of the datasheet "bst-bmi270-ds000.pdf"
Signed-off-by: William MARTIN <william.martin@power-lan.com>
As of today <zephyr/zephyr.h> is 100% equivalent to <zephyr/kernel.h>.
This patch proposes to then include <zephyr/kernel.h> instead of
<zephyr/zephyr.h> since it is more clear that you are including the
Kernel APIs and (probably) nothing else. <zephyr/zephyr.h> sounds like a
catch-all header that may be confusing. Most applications need to
include a bunch of other things to compile, e.g. driver headers or
subsystem headers like BT, logging, etc.
The idea of a catch-all header in Zephyr is probably not feasible
anyway. Reason is that Zephyr is not a library, like it could be for
example `libpython`. Zephyr provides many utilities nowadays: a kernel,
drivers, subsystems, etc and things will likely grow. A catch-all header
would be massive, difficult to keep up-to-date. It is also likely that
an application will only build a small subset. Note that subsystem-level
headers may use a catch-all approach to make things easier, though.
NOTE: This patch is **NOT** removing the header, just removing its usage
in-tree. I'd advocate for its deprecation (add a #warning on it), but I
understand many people will have concerns.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
To reduce energy consumption for accel and gyro frequencies 52 Hz and
lower, disable high performance mode by default.
It doesn't affect for higher frequencies.
Signed-off-by: Adrian Wojak <adrian.wojak@grinn-global.com>
1. Use #ifdef around CONFIG_HTS221_TRIGGER instead of #if
2. According to binding (which is in line with datasheet), name of the pin
used for trigger mode should be drdy, not irq.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adjust the names of the operating modes to match them
with the datasheet and INA230 pattern. While at it add
the missing INA237_OPER_MODE_TEMP_TRIG mode.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
hts221_trigger.c is pulled in by the CMakeLists.txt file when
CONFIG_HTS221_TRIGGER is defined. Therefore make the source in hts221.c use
the some define.
This removes also the (wrong) warning
<inf> HTS221: Cannot enable trigger without drdy-gpios
even when "drdy-gpios" is defined in the device-tree.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Add missing support for the triggered mode using GPIO
interrupt alert pin. It uses mode detection at runtime
which allows working multiple sensors with different
modes simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix a call that writes Register 29 - Accelerometer Configuration 2.
Due to an obvious copy-paste mistake in the code, this register was
written with a DLPF setting from devicetree intended for gyroscope,
not for accelerometer (and the latter was effectively ignored).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
According to the BME680 datasheet, only the spi_mem_page bit can be
changed in its 8-bit register. Therefore we shouldn't just write 0s
to the remaining bits, but update the register content in read-modify-write
fashion instead.
Rework the bme680_set_mem_page(), bme680_init() and register-access
macros.
Signed-off-by: Jan Kuliga <jtkuliga@gmail.com>
Add support for reading the VFOCV register, which contains the model
estimated open circuit voltage for the cell.
Link: https://pdfserv.maximintegrated.com/en/an/AN6358.pdf
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fixes a bus fault observed in samples/boards/reel_board/mesh_badge
caused by dereferencing an uninitialized device pointer in the apds9960
sensor driver. The device pointer needs to be initialized regardless of
how CONFIG_APDS9960_TRIGGER is configured.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
The adxl372 device does not select the correct bus that it is on, which
causes undefined operation (usually a fault). This driver should not be
using Kconfig to determine which bus to use, that should be done by
dts, however this works as a quick fix in the interim until the driver
can be fixed properly.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Sensor value unit is [m/s^2].
Currently calcs as [g/1000] unit.
Correcting calculation to convert [m/s^2].
Store the integer part to val1, and the fractional part to val2.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
The def command Indicates that a comment block contains documentation
for a #define macro. This is useful if the comment block documents a
macro not adjacent to it, e.g.
```c
/**
* @def MAX(x,y)
* @brief Computes the maximum of @a x and @a y.
*/
#ifdef XXX
#define MAX(x,y) ...
#endif
```
However, it is not necessary if the comment is adjacent to the
definition, e.g.
```c
/**
* @brief Computes the maximum of @a x and @a y.
*/
#define MAX(x,y) ...
```
This patch removes all unnecessary def entries in-tree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
