`spi_is_ready` function is being deprecated in favor of
`spi_is_ready_dt` so let's replace the old usage in the tree.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Refactors all sensor drivers to use SENSOR_DEVICE_DT_INST_DEFINE, which
is a sensor-specific variant of DEVICE_DT_INST_DEFINE that provides a
common place to instantiate additional data structures for the future
sensor subsystem and/or sensor driver stats.
This approach was inspired by I2C_DEVICE_DT_INST_DEFINE to streamline
adding I2C stats support across all I2C drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
On power on reset, after disable advanced power safe mode,
you need to wait a delay before write again in the device.
The missing wait produce random initialization failure.
See §4.4 of the datasheet "bst-bmi270-ds000.pdf"
Signed-off-by: William MARTIN <william.martin@power-lan.com>
This change in pattern is meant to address a misconfiguration issue
that can occur for sensors that support being on multiple busses
like I2C & SPI.
For example, you can have a configuration in which such a sensor is
on the I2C bus in the devicetree and the sensor is enabled. However
the application configuration enables CONFIG_SPI=y and CONFIG_I2C=n
and this will cause the sensor driver to be built by default, however
since we don't have the I2C bus enabled the driver will not compile
correctly.
Previously we had been adding to board Kconfig.defconfig something
like:
config I2C
default y if SENSOR
This pattern doesn't scale well and may differ from what an application
specific need/use is.
So instead move to a pattern in which we leave the default enablement
up to the devicetree "status" property for the sensor. We then have
the Kconfig move from 'depends on <BUS>' to 'select <BUS>' and in
the case of drivers that support multiple busses we have the Kconfig
be: 'select <BUS> if $(dt_compat_on_bus,$(<DT_COMPAT>),<BUS>) for
each bus type the sensor supports.
This removes the need to add Kconfig logic to each board and enables
the bus subsystem and bus controller driver if the sensor requires
it by default in the build system.
Fixes: #48518
Signed-off-by: Kumar Gala <galak@kernel.org>
Update sensor drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
- Per datasheet (Rev 1.0, Page 29): When enabling adv_power_save, there
needs to be a 1ms inter-write registers delay. With this addition, the
driver will work at SCLK frequencies faster than 100kHz.
- Added helper function reg_write_with_delay() to factor these writes.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
In drivers/sensor/CMakeLists.txt, we have various lines like this:
add_subdirectory_ifdef(CONFIG_FOO foo)
Then drivers/sensor/foo/CMakeLists.txt says:
zephyr_library()
zephyr_library_sources_ifdef(CONFIG_FOO foo.c)
This is redundant; the foo/CMakeLists.txt won't be added to the build
system unless CONFIG_FOO=y in the first place, so there's no need for
extra boilerplate testing it again.
Remove all these unnecessary instances in each sensor driver's
CMakeLists.txt using this pattern:
zephyr_library()
zephyr_library_sources(foo.c)
In a couple of places, the '.c' extension is missing. Add them in for
consistency when that happens.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
