Cloned from counter_basic_api with modifications based on DS3231
limitations:
* Only one device tested per board;
* Counter cannot be stopped or started;
* Alarms are serviced by worker thread, so are not invoked from ISR
and require that test thread yield to allow processing (no
k_busy_wait());
* Multiple Alarms test is disabled as documented in test.
Additional tests were added for DS3231-specific API.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the SPI testing support with an internal MOSI to MISO
loopback for the Atmel SAM R21 Xplained Pro board.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the SPI testing support with an internal MOSI to MISO
loopback for the Atmel SAM E54 Xplained Pro board.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
A number of uart drivers may not implement the uart_configure and
uart_config_get APIs, if we get -ENOTSUP treat that as a skip.
Fixes#24355
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32 and CC13xx/CC26xx SPI drivers don't utilize the Kconfig
symbols for per instance SPI anymore so we don't need to set them on the
conf files for this test.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The STM32 I2C drivers don't utilize the Kconfig symbols for per
instance I2C anymore so we don't need to set them in the
conf files for this test.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
harness being set without actual use of harness (via harness_config)
makes the test behave differently.
Fixes#24661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_RTC_0_NAME to DT_LABEL() references based on the compat being
defined in the build.
Introduce a set of macros that will generate a list of labels based on
compatible matches.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This configures the nucleo_f411re board for testing the SPI loopback
with DMA V1 transfer. DMA instance 2 is used.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg boardtest dma_V1
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This configures the nucleo_l476rg board for testing the SPI loopback
when with DMA transfer.
It requires pin MOSI to be connected to pin MISO of the SPI1
SPI tx/rx are assigned to the request ID 1 of dma1 channels 3 and 2
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a new testcase in the spi_loopback test application
to use several buffers for the DMA transfer.
It requires the MOSI to be connected to the MISO of the SPI1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This changes the spi_loopback test application to use the DMA transfer.
In case of DMA, some testcases are useless.
It requires the MOSI to be connected to the MISO of the SPI1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert DT_UART_{0,1}_NAME to DT_NODELABEL() references as the cases are
board specific and this allows us to remove DT_UART_{0,1}_NAME defines
in dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for running the DAC loopback test case on the NXP
FRDM-K64F development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for running the DAC loopback test case on the NXP
TWR-KE18F development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The hwinfo driver test currently filters for `CONFIG_HWINFO`, but this
symbol is set to `y` by the `prj.conf` and therefore will always be
selected.
This commit removes the unnecessary `CONFIG_HWINFO` filter.
Note that the hwinfo driver test `ifdef`s `CONFIG_HWINFO_HAS_DRIVER`,
and having an actual hwinfo driver implementation is not a requirement
(if no hwinfo driver is available, the test validates that -ENOTSUP is
returned by `hwinfo_get_device_id`).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Test is checking if alarm handler is executed at request time or later.
However, validation did not take into account wrapping of the counter.
Fixed by taking into account case where counter wraps.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Fixes test which did not take into account that counter may
wrap (nrf51 has 16bit timers) and was setting alarm to wrong
value. Error was not seen on platforms with higher top value.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds the asynchronous UART API testing support on the SAM
D21 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
No in-tree boards support the NINT signal on an SX1509B IO extender,
so test using custom overlays/configurations for the Particle Xenon
board using an SX1509B breakout board.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Changes to Kconfig vs devicetree resulted in uart1 being enabled,
which steals the test pins away from the test.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Move to the new devicetree API and stop using DT_WDT_0_NAME fixup
macros. All existing in-tree SoCs with fixup names are still supported
here via compatible. The watchdog0 alias is also still supported.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The board rename was missed. That's the only remaining case of a
missed rename I could find in tree, but I may have missed something.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
