Add uart configuration for UART driver, add frdm_ke17z512_uart.overlay
and update testcase.yml to support UART testing.
There are LPUART and UART IPs in frdm_ke17z512 platforms, so add
additional shell tests as UART, the shell instructions can be entered
on the UART console window.
Signed-off-by: Anke Xiao <anke.xiao@nxp.com>
Fix failed test for platforms with flash program size > 128 bytes.
Update supported program size to 512 bytes, the highest supported
program size by Zephyr platforms.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Adafruit feather is a generic name that could match many
boards. Renamed to reflect actual board name:
- Adafruit Feather nrf52840 Express
There are two boards based on the nrf52840, so keeping directory
generic to support additional board defs with mostly shared dts.
Signed-off-by: Jacob Winther <jacob@9.nz>
Add a void *user_data pointer to the input callback structure. This is
useful for driver to get back the driver data structure and avoid
defining wrapper functions.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add frdm_ke17z_fgpio.overlay to add fgpio configuration, and
add update testcase.yml to add FGPIO driver test for frdm_ke17z
and frdm_ke17z512 platforms.
Updated ke17z512 gpio test pins to avoid conflicts with I2C pin.
Signed-off-by: Anke Xiao <anke.xiao@nxp.com>
Add an emulated UART device test case. Demonstrate using the
zephyr,uart-emul bus for passing data to an emulated implementation for a
UART device driver.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
The LSM9DS1 is a system-in-package featuring
a 3D digital linear acceleration sensor, a 3D digital angular rate
sensor and a 3D digital magnetic sensor.
This driver implements only the linear acceleration sensor and the
angular rate sensor, on the I2C bus.
This driver is without trigger support.
The driver is based on the stmemsc HAL.
link: https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Signed-off-by: Miguel Gazquez <miguel.gazquez@bootlin.com>
There is problem with running this test in validation,
because of DBGR mode watchdog can't reset board by itself,
and it needs cold reset. This proves that test is not automated,
and should be exluded on this board.
Signed-off-by: Patryk Kuniecki <patryk.kuniecki@intel.com>
The driver right now only allows inverting the input value, which can be
useful for differential channels but is quite confusing for single ended
ones. Implement a simple output inversion flag instead to make up for
that.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add more memory to dma region for cpurad as otherwise it fails
during initialization due to not enough memory for dmm heap.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
find_package() already deals with finding ZEPHYR_BASE, so do not rely on
it being set in ENV, use the variable directly adter find_package() was
called.
Fixes#75387
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These properties are not used by the driver at all, but are
inconveniently marked as required. Lets just remove them.
Signed-off-by: Brett Witherspoon <brett@witherspoon.engineering>
Rework configuration so that it does not require special treatment
in testcase.yaml.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Rework configuration so that it does not require special treatment
in testcase.yaml.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Remove an overlay with a wrong name not being picked up,
and change the "A" revision overlay to be used by all revisions.
Also fix the "clocks" property in the overlay causing a fault with sai4.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This commit changes the adc_api test to use the proper printf
format specifier when printing the ADC samplings. This ensures
that all values are printed on 16-bit. Without this specifier,
negative values are sign-extended and printed on full integer
size (e.g., 0x8000 -> "0xFFFF8000").
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
In order to support back-to-back readings, it's required that the
RTIO workq threads priority is higher than the caller issuing the
back-to-back requests, otherwise the requests will fail as P4WQ won't
have the opportunity to clear the is_done semaphore, and the subsequent
request will be rejected.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
The rtc test suite uses timegm to convert a unix
timestamp to datetime, specifically struct tm which has no
nsec field, so the nsec field is not initialized properly.
Update tests to init nsec and isdst members of struct rtc_time.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Disable the pll2 when clearing the clock config prior to
testing the clock_control driver for the stm32h7
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fix build error due to cmake requiring a separate
overlay for each of this target's SOCs.
Error being fixed:
```
-- Board: sam_v71_xult, qualifiers: samv71q21
CMake Error at cmake/modules/extensions.cmake:2742 (message):
Board sam_v71_xult defines multiple SoCs.
Shortened file name (sam_v71_xult.overlay) not allowed, use
'<board>_<soc>.overlay' naming
```
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This commit removes the const qualifier from TX (source) buffer
of the chan_blen_transfer DMA test to ensure it gets placed in
RAM rather than flash. This ensures the test can pass on hardware
where the DMA controller is unable to access flash.
Fixes#75125.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
Boards that use 1024 byte EEPROM buffers need 16-bit address widths
otherwise eeprom_target driver will cause build failure.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
Existing tests fail when 16-bit address width is used. Adjust the code
to support 16-bit addresses as well.
Signed-off-by: Tahsin Mutlugun <Tahsin.Mutlugun@analog.com>
The current version of scipts do not consider OOT boards use cases and
the tests with robot now are strict to only one robot file, which is
not realistic for real environment. This address those issues and allow
multiple testsuits at command line and lists at tests entries. It add
another test parameter to allow configure robotframework options.
Fixes: #74563
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Add missing pull-up for RX pin in nrf54h20dk dual uart configuration.
Lack of pull-up was causing test failures.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
RTCs support a variety of combinations of alarm time fields, set
by the alarm time mask. Until now, alarm tests have selected
only the minute and hour fields, as these are always supported,
but some RTCs require setting every supported field when setting
the alarm time, while other RTCs don't support setting every field.
To support all RTCs in the test suite, a configuration has been
added which makes the alarm time mask configurable. Boards can now
define the specific alarm time mask they want to test within
their boards .conf files.
Additionally, the alarm tests have been refactored to not depend
on the time.h library to determine the struct rtc_time times to
set as these are constant, so they are now provided as const
structs instead.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
nRF54H20 USB device controller cannot be enabled without VBUS, but the
device should not be connected to the host during testing. Add it to
build_only section.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Do not halt control endpoint, control endpoint may not be enabled when
there no host is connected. Yield after buffer is queued to allow the
driver to work.
Tweak pool size and number of buffers to pass the test with high-speed
drivers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Restore the default CAN bitrates after having tested setting bitrate and
timing. This ensures the arbitration phase bitrate is proportional to the
data phase bitrate, allowing CAN FD transmission tests to complete.
Fixes: #73723
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This nucleo board inherit from the root `h5` dts some special nodes:
- `vbat` on adc1 channel 2
- `vref` on adc1 channel 17
- `die_temp` on adc1 channel 16
The issue is discussed here:
https://github.com/zephyrproject-rtos/zephyr/issues/72914
Signed-off-by: Alex Fabre <alex.fabre@rtone.fr>
Optee driver should handle GET_THREAD_COUNT call. This limitation is
set in Optee-OS during build and limits number of symultanious calls
to optee. Add sym to handle this limitation.
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
Capabilities should be set correctly or optee will show error message:
[00:00:00.000,000] <err> optee: OPTEE does not support dynamic shared
memory
Test suite should set optee UID or the following error message should
be displayed:
[00:00:00.000,000] <err> optee: OPTEE API UID mismatch
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
During SMC_RPC_FUNC_ALLOC call optee driver puts new shm object to a4
and a5 variables and then expects this object to be in a1 and a2 from
OP-TEE OS. Fixed behaviour so normal_call callback will act the same
way as OP-TEE OS
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
This should test OP-TEE driver basic functionality without
communication with real OPTEE OS.
Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
The board didn't have a proper overlay for the test and failed to build
the test case causing CI failures.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Fix the devicetree bindings to actually be used as the default
configuration, following the example set by various ST sensor devices.
This requires sadly dropping enums and using #defines for various
options as well as repeating many numbers, but presumably is the way to
do it given the precedent set by ST with sensors like the lsm6dso.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
